Legalize / European Union / Implementing Regulation

Commission Implementing Regulation (EU) No 1124/2012 of 26 November 2012 concerning the classification of certain goods in the Combined Nomenclature

Type Implementing Regulation

Publication 2012-12-01

State In force

Text As published

Department European Commission

Source EUR-Lex

articles 3

This is the act as published. Later amendments are not folded into the text below: each one is a separate act in this repository and an entry in this law's history.

Reform history JSON API


1.12.2012	EN	Official Journal of the European Union	L 331/7

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Council Regulation (EEC) No 2658/87 of 23 July 1987 on the tariff and statistical nomenclature and on the Common Customs Tariff [^ntr1-L_2012331EN.01000701-E0001], and in particular Article 9(1)(a) thereof,

Whereas:

(1) In order to ensure uniform application of the Combined Nomenclature annexed to Regulation (EEC) No 2658/87, it is necessary to adopt measures concerning the classification of the goods referred to in the Annex to this Regulation.

(2) Regulation (EEC) No 2658/87 has laid down the general rules for the interpretation of the Combined Nomenclature. Those rules apply also to any other nomenclature which is wholly or partly based on it or which adds any additional subdivision to it and which is established by specific provisions of the Union, with a view to the application of tariff and other measures relating to trade in goods.

(3) Pursuant to those general rules, the goods described in column (1) of the table set out in the Annex should be classified under the CN code indicated in column (2), by virtue of the reasons set out in column (3) of that table.

(4) It is appropriate to provide that binding tariff information which has been issued by the customs authorities of Member States in respect of the classification of goods in the Combined Nomenclature but which is not in accordance with this Regulation can, for a period of three months, continue to be invoked by the holder, under Article 12(6) of Council Regulation (EEC) No 2913/92 of 12 October 1992 establishing the Community Customs Code [^ntr2-L_2012331EN.01000701-E0002].

(5) The measures provided for in this Regulation are in accordance with the opinion of the Customs Code Committee,

HAS ADOPTED THIS REGULATION:

Article 1

The goods described in column (1) of the table set out in the Annex shall be classified within the Combined Nomenclature under the CN code indicated in column (2) of that table.

Article 2

Binding tariff information issued by the customs authorities of Member States, which is not in accordance with this Regulation, can continue to be invoked for a period of three months under Article 12(6) of Regulation (EEC) No 2913/92.

Article 3

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 26 November 2012.

For the Commission, On behalf of the President,

Algirdas ŠEMETA

Member of the Commission

[^ntr1-L_2012331EN.01000701-E0001]: OJ L 256, 7.9.1987, p. 1.

[^ntr2-L_2012331EN.01000701-E0002]: OJ L 302, 19.10.1992, p. 1.

ANNEX

Description of the goods	Classification (CN code)	Reasons
(1)	(2)	(3)
A hermetically sealed weighing sensor (so-called "load cell") incorporating a strain gauge in the form of a bridge circuit with dimensions of approximately 13 × 3 × 3 cm. The load cell operates at the deflection of the strain gauge filament when it is subjected to a physical force. The physical force creates a change in resistance of the filament, thereby unbalancing the bridge circuit which in turn changes the voltage of the current passing through. The load cell converts the physical force acting on it into an electrical signal proportional to that force. The signal is read out, processed and shown by a device not included upon presentation. The load cell is designed to be used, for example, in floor scales, blenders, hoppers and tank scales.	9031 80 98	Classification is determined by General Rules 1, 2(a) and 6 for the interpretation of the Combined Nomenclature, Note 1(m) to Section XVI and by the wording of CN codes 9031 , 9031 80 and 9031 80 98 . The load cell is designed for converting physical force into an electrical signal for measuring purposes. As it does not itself show the result of the measurement, it is considered to be an incomplete measuring instrument not specified or included elsewhere in Chapter 90. Consequently, classification under heading 8423 as a part of weighing machinery is excluded (see also the HS Explanatory Notes to heading 9031 , (A), point (30)). The article is therefore to be classified under CN code 9031 80 98 as other instruments not specified or included elsewhere in Chapter 90.

Reading this document does not replace reading the official text published in the Official Journal of the European Union. We assume no responsibility for any inaccuracies arising from the conversion of the original to this format.

This text is published under EUR-Lex's own terms of reuse, not a Legalize or public-domain licence. EUR-Lex
Creative Commons Attribution 4.0 International (CC BY 4.0)
© European Union, https://eur-lex.europa.eu — Source: EUR-Lex (Publications Office of the European Union). Reused under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Only EU legislation published in the printed Official Journal of the European Union is deemed authentic; consolidated texts are reproduced here for documentation purposes and have been reformatted to Markdown.