LegalizeCommission Implementing Regulation (EU) 2018/1853 of 27 November 2018 granting a Union authorisation for the biocidal product family Teat disinfectants biocidal product family of CVAS (Text with EEA relevance.)
This is the act as published. Later amendments are not folded into the text below: each one is a separate act in this repository and an entry in this law's history.
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product and insert a suction tube of the robotic milking device. Avoid discharge of surplus fluids.
The teats are cleaned by robot with automatic brushes.
After robotic milking, the disinfectant is sprayed automatically onto teats from a cluster arm.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
Rinsing of the sprayer is automatic.
4.5.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE 8 OF THE META SPC 5
5.1. Instructions for use
See use specific instructions for use.
5.2. Risk mitigation measures
See use specific risk mitigation measures.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
Mentioned in the MSDS
Description of first aid measures
After inhalation: Supply fresh air; consult doctor in case of symptoms.
After skin contact: Instantly wash with water and soap and rinse thoroughly.
After eye contact: Rinse opened eye for several minutes under running water (at least 15 minutes).
After swallowing: Rinse out mouth and then drink plenty of water. Instantly call for doctor.
If medical advice is needed, have product container or label at hand.
Stability and reactivity
Reactivity: No dangerous reactions known.
Chemical stability: The product is chemically stable under normal surroundings terms (ambient temperature).
Possibility of hazardous reactions: By designated use no dangerous reactions are to be expected.
Conditions to avoid: Not determined.
Incompatible materials: Not determined.
Hazardous decomposition products: No dangerous decomposition products known.
Accidental release measures
Personal precautions, protective equipment and emergency procedures: Wear protective clothing.
Ensure adequate ventilation.
Keep ignition sources away — Do not smoke.
Environmental precautions: Do not allow to enter drainage system, surface or ground water.
Methods and material for containment and cleaning up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose of the material collected according to regulations.
5.4. Instructions for safe disposal of the product and its packaging
Mentioned in the MSDS
Waste treatment methods: Hazardous waste (AVV). Must not be disposed of together with household garbage. Do not allow product to reach sewage system. Must be specially treated under adherence to official regulations.
At the end of the treatment, dispose unused product and the packaging in accordance with local requirements. Used product can be flushed to the municipal sewer or disposed to the manure deposit depending on local requirements. Avoid release to an individual waste water treatment plant.
Recommended cleaning agent: Water, if needed detergent.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Shelf-life: 18 months
Products need to be protected from frost, stored at temperatures not exceeding 30 °C and away from direct sunlight.
6. OTHER INFORMATION
—
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 5
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Dip es SF Dip es SF 3.0 Iod Dip S 30 P Dip es SF 1.4 Iod-Dip S 14 P EUTADIPP | Dip es SF Dip es SF 3.0 Iod Dip S 30 P Dip es SF 1.4 Iod-Dip S 14 P EUTADIPP | Dip es SF Dip es SF 3.0 Iod Dip S 30 P Dip es SF 1.4 Iod-Dip S 14 P EUTADIPP | Dip es SF Dip es SF 3.0 Iod Dip S 30 P Dip es SF 1.4 Iod-Dip S 14 P EUTADIPP | Dip es SF Dip es SF 3.0 Iod Dip S 30 P Dip es SF 1.4 Iod-Dip S 14 P EUTADIPP |
| Authorisation number | EU-0018724-0006 1-5 | EU-0018724-0006 1-5 | EU-0018724-0006 1-5 | EU-0018724-0006 1-5 | EU-0018724-0006 1-5 |
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 1,16 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0 |
META SPC 6
1. META SPC 6 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 6 identifier
| Identifier | meta SPC 6 |
1.2. Suffix to the authorisation number
| Number | 1-6 |
1.3. Product type(s)
| Product type(s) | PT03 — Veterinary hygiene (Disinfectants) |
|---|---|
2. META SPC 6 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 6
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) | Content (%) |
|---|---|---|---|---|---|---|
| Common name | IUPAC name | Function | CAS number | EC number | Min | Max |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0 | 0 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 1,16 | 1,16 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0 | 0 |
2.2. Type(s) of formulation of the meta SPC 6
| Formulation | AL — Any other liquid |
|---|---|
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 6
| Hazard statements | |
| Precautionary statements | If medical advice is needed, have product container or label at hand. Keep out of reach of children. |
4. AUTHORISED USE(S) OF THE META SPC 6
4.1. Use description
Table 17. Use # 1 — Teat disinfection of milkable animals: Pre-milking teat disinfection by manual foaming
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use before milking |
| Application method(s) | Manual foaming using a foam cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Pre-milking application: 2-3×/day (before each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.1.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the foam cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth before pre-milking disinfection.
Before milking, squeeze the reservoir and put the foam cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Leave the product on the teats for at least 60 seconds.
Refill the cup of the foaming unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After disinfection, empty the reservoir and clean reservoir and foam cup by rinsing with water.
4.1.2. Use-specific risk mitigation measures
This product can be used for pre- and post-milking disinfection in combination. However, it should not be used in combination with a different iodine-based product
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 18. Use # 2 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual foaming
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual foaming using a foam cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2 - 3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.2.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the foam cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After milking, squeeze the reservoir and put the foam cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Refill the cup of the foaming unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and foam cup by rinsing with water.
4.2.2. Use-specific risk mitigation measures
This product can be used for pre- and post-milking disinfection in combination. However, it should not be used in combination with a different iodine-based product
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 19. Use # 3 — Teat disinfection of milkable animals: Post-milking teat disinfection by automated foaming
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria- Yeasts- |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Automated foaming |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2 - 3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.3.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product and insert a suction tube of the automated foaming-system. Avoid discharge of surplus fluids.
After milking, the vacuum is shut off and the teat disinfectant is injected into a manifold on the clawpiece. The teats are coated with ca. 5 mL of foam when the teat foam cup is withdrawn by the Automatic Cluster Removal (ACR). After the removal of the ACR, every liner of the automated foaming-system is thoroughly rinsed with water and blown out with compressed air.
In a final cleaning step after each milking session of the herd, the liners are disinfected (e.g. with a chlorine-based product) and blown out again with compressed air.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
Afterwards, the milking system is ready for the next milking event.
The whole process is automated.
4.3.2. Use-specific risk mitigation measures
This product can be used for pre- and post-milking disinfection in combination. However, it should not be used in combination with a different iodine-based product
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 20. Use # 4 — Teat disinfection of milkable animals: Pre- and post-milking teat disinfection by manual foaming
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use before and after milking |
| Application method(s) | Manual foaming using a foam cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Pre- and post-milking application: 4-6 times per day (before and after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.4.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the foam cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth before pre-milking disinfection.
Before milking, squeeze the reservoir and put the foam cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Leave the product on the teats for at least 60 seconds.
Clean the teats carefully by wiping with a cloth immediately before milking. After milking, repeat the disinfection by foaming as described above.
Refill the cup of the foaming unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and foam cup by rinsing with water.
4.4.2. Use-specific risk mitigation measures
This product can be used for pre- and post-milking disinfection in combination. However, it should not be used in combination with a different iodine-based product
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE 9 OF THE META SPC 6
5.1. Instructions for use
See use specific instructions for use.
5.2. Risk mitigation measures
See use specific risk mitigation measures.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
Mentioned in the MSDS
Description of first aid measures
After inhalation: Supply fresh air; consult doctor in case of symptoms.
After skin contact: Instantly wash with water and soap and rinse thoroughly.
After eye contact: Rinse opened eye for several minutes under running water (at least 15 minutes).
After swallowing: Rinse out mouth and then drink plenty of water. Instantly call for doctor.
If medical advice is needed, have product container or label at hand.
Stability and reactivity
Reactivity: No dangerous reactions known.
Chemical stability: The product is chemically stable under normal surroundings terms (ambient temperature).
Possibility of hazardous reactions: By designated use no dangerous reactions are to be expected.
Conditions to avoid: Not determined.
Incompatible materials: Not determined.
Hazardous decomposition products: No dangerous decomposition products known.
Accidental release measures
Personal precautions, protective equipment and emergency procedures:
Wear protective clothing.
Ensure adequate ventilation.
Keep ignition sources away — Do not smoke.
Environmental precautions: Do not allow to enter drainage system, surface or ground water.
Methods and material for containment and cleaning up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose of the material collected according to regulations.
5.4. Instructions for safe disposal of the product and its packaging
Mentioned in the MSDS
Waste treatment methods: Hazardous waste (AVV). Must not be disposed of together with household garbage. Do not allow product to reach sewage system. Must be specially treated under adherence to official regulations.
At the end of the treatment, dispose unused product and the packaging in accordance with local requirements. Used product can be flushed to the municipal sewer or disposed to the manure deposit depending on local requirements. Avoid release to an individual waste water treatment plant.
Recommended cleaning agent: Water, if needed detergent.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Shelf-life: 18 months
Products need to be protected from frost, stored at temperatures not exceeding 30 °C and away from direct sunlight.
6. OTHER INFORMATION
—
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 6
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | Dip es Io-foam Dip es Io-foam 1.4 Iod-Dip Io-foam BaktoStop foam | Dip es Io-foam Dip es Io-foam 1.4 Iod-Dip Io-foam BaktoStop foam | Dip es Io-foam Dip es Io-foam 1.4 Iod-Dip Io-foam BaktoStop foam | Dip es Io-foam Dip es Io-foam 1.4 Iod-Dip Io-foam BaktoStop foam | Dip es Io-foam Dip es Io-foam 1.4 Iod-Dip Io-foam BaktoStop foam |
| Authorisation number | EU-0018724-0007 1-6 | EU-0018724-0007 1-6 | EU-0018724-0007 1-6 | EU-0018724-0007 1-6 | EU-0018724-0007 1-6 |
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 1,16 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0 |
META SPC 7
1. META SPC 7 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 7 identifier
| Identifier | meta SPC 7 |
1.2. Suffix to the authorisation number
| Number | 1-7 |
1.3. Product type(s)
| Product type(s) | PT03 — Veterinary hygiene (Disinfectants) |
|---|---|
2. META SPC 7 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 7
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) | Content (%) |
|---|---|---|---|---|---|---|
| Common name | IUPAC name | Function | CAS number | EC number | Min | Max |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0,14 | 0,14 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 0 | 0 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0,11 | 0,33 |
2.2. Type(s) of formulation of the meta SPC 7
| Formulation | AL — Any other liquid |
|---|---|
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 7
| Hazard statements | Harmful to aquatic life with long lasting effects. |
| Precautionary statements | Avoid release to the environment. Dispose of contents to local/regional/national/international regulation. Dispose of container to local/regional/national/international regulation. |
4. AUTHORISED USE(S) OF THE META SPC 7
4.1. Use description
Table 21. Use # 1 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual dipping
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual dipping using a dip cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.1.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the dip cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After milking, squeeze the reservoir and put the dip cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Refill the cup of the dipping unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and dip cup by rinsing with water.
4.1.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 22. Use # 2 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual foaming
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual foaming using a foam cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.2.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the foam cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After milking, squeeze the reservoir and put the foam cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Refill the cup of the foaming unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and foam cup by rinsing with water.
4.2.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 23. Use # 3 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual spraying using a trigger sprayer
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual spraying using a trigger sprayer |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.3.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the top of the trigger sprayer on it. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After milking, spray the disinfectant on the teats using the trigger sprayer making sure that about 3 cm of the teat around the streak canal are covered with the disinfectant.
Refill the reservoir of the trigger sprayer with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and trigger sprayer by rinsing with water.
4.3.2. Use-specific risk mitigation measures
Use chemical resistant gloves (glove material to be specified by the authorisation holder within the product information) during postmilking teat disinfection by manual spraying using a trigger sprayer.
Avoid working in spray mist.
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 24. Use # 4 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual spraying using an electronic sprayer
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual spraying using an electronic sprayer |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.4.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product assuming 5 mL product per cow and insert a sucking lance of the electronic sprayer. Avoid discharge of surplus fluids.
Clean carefully the teats by wiping with a single service paper towel/cloth before milking.
After milking, spray the disinfectant on the teats using the electronic sprayer making sure that about 3 cm of the teat around the streak canal are covered with the disinfectant.
Replace the empty can by a new can containing the RTU product as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, put the sucking lance system into a bucket of water and rinse the sprayer by pumping the water through the sprayer.
4.4.2. Use-specific risk mitigation measures
Use chemical resistant gloves (glove material to be specified by the authorisation holder within the product information) during post/milking teat disinfection by manual spraying using an electronic sprayer.
Avoid working in spray mist.
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.5. Use description
Table 25. Use # 5 — Teat disinfection of milkable animals: Post-milking teat disinfection by automated dipping
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Automated dipping |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.5.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product and insert a suction tube of the automated dipping-system. Avoid discharge of surplus fluids.
After milking, the vacuum is shut off and the teat dip is injected into a manifold on the clawpiece. The teats are coated with ca. 5 mL of dip when the teat cup is withdrawn by the Automatic Cluster Removal (ACR). After the removal of the ACR, every liner of the automated dipping-system is thoroughly rinsed with water and blown out with compressed air.
In a final cleaning step after each milking session of the herd, the liners are disinfected (e.g. with a chlorine-based product) and blown out again with compressed air.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
Afterwards, the milking system is ready for the next milking event.
The whole process is automated.
4.5.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.6. Use description
Table 26. Use # 6 — Teat disinfection of milkable animals: Post-milking teat disinfection by automated foaming
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Automated foaming |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.6.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product and insert a suction tube of the automated foaming-system. Avoid discharge of surplus fluids.
After milking, the vacuum is shut off and the teat disinfectant is injected into a manifold on the clawpiece. The teats are coated with ca. 5 mL of foam when the teat foam cup is withdrawn by the Automatic Cluster Removal (ACR). After the removal of the ACR, every liner of the automated foaming-system is thoroughly rinsed with water and blown out with compressed air.
In a final cleaning step after each milking session of the herd, the liners are disinfected (e.g. with a chlorine-based product) and blown out again with compressed air.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
Afterwards, the milking system is ready for the next milking event.
The whole process is automated.
4.6.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.6.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.6.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.6.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.7. Use description
Table 27. Use # 7 — Teat disinfection of milkable animals: Post-milking teat disinfection by automated spraying by robot
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Automated spraying by robot |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.7.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product and insert a suction tube of the robotic milking device. Avoid discharge of surplus fluids.
The teats are cleaned by robot with automatic brushes.
After robotic milking, the disinfectant is sprayed automatically onto teats from a cluster arm.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
Rinsing of the sprayer is automatic.
4.7.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.7.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.7.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.7.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE 10 OF THE META SPC 7
5.1. Instructions for use
See use specific instructions for use.
5.2. Risk mitigation measures
See use specific risk mitigation measures.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
Mentioned in the MSDS
Description of first aid measures
After inhalation: Supply fresh air; consult doctor in case of symptoms.
After skin contact: Wash with water and soap.
After eye contact: Rinse opened eye for several minutes under running water. Then consult doctor.
After swallowing: Rinse out mouth and then drink plenty of water. Seek immediate medical advice.
Stability and reactivity
Possibility of hazardous reactions: Reaction with oxidant- and reducing agent.
Conditions to avoid: No further relevant information available.
Incompatible materials: No further relevant information available.
Hazardous decomposition products: iodine (when warming up).
Accidental release measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Environmental precautions: Do not allow product to reach sewage systems or water bodies in great quantities.
Methods and material for containment and cleaning up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose of the material collected according to regulations.
5.4. Instructions for safe disposal of the product and its packaging
Mentioned in the MSDS
Waste treatment methods
Recommendation: Must be specially treated with regard to official regulations.
Waste disposal key number: Corresponding to the regulation of the European Waste catalogue the relation of the waste key numbers has to be made specific to industry and process.
European waste catalogue: Corresponding to the regulation of the EWC the relation of the waste key numbers has to be made specific to industry and process.
At the end of the treatment, dispose unused product and the packaging in accordance with local requirements. Used product can be flushed to the municipal sewer or disposed to the manure deposit depending on local requirements. Avoid release to an individual waste water treatment plant.
Recommended cleaning agent: Water, if necessary with cleaning agent.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Shelf-life: 24 months
Products need to be protected from frost, stored at temperatures not exceeding 30 °C and away from direct sunlight.
6. OTHER INFORMATION
—
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 7
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | calgodip D 1200 Jod-Dip S 12 Dip es SF 1200 | calgodip D 1200 Jod-Dip S 12 Dip es SF 1200 | calgodip D 1200 Jod-Dip S 12 Dip es SF 1200 | calgodip D 1200 Jod-Dip S 12 Dip es SF 1200 | calgodip D 1200 Jod-Dip S 12 Dip es SF 1200 |
| Authorisation number | EU-0018724-0008 1-7 | EU-0018724-0008 1-7 | EU-0018724-0008 1-7 | EU-0018724-0008 1-7 | EU-0018724-0008 1-7 |
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0,14 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 0 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0,15 |
META SPC 8
1. META SPC 8 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 8 identifier
| Identifier | meta SPC 8 |
1.2. Suffix to the authorisation number
| Number | 1-8 |
1.3. Product type(s)
| Product type(s) | PT03 — Veterinary hygiene (Disinfectants) |
|---|---|
2. META SPC 8 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 8
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) | Content (%) |
|---|---|---|---|---|---|---|
| Common name | IUPAC name | Function | CAS number | EC number | Min | Max |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0,14 | 0,54 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 0 | 0 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0,11 | 0,33 |
2.2. Type(s) of formulation of the meta SPC 8
| Formulation | AL — Any other liquid |
|---|---|
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 8
| Hazard statements | Harmful to aquatic life with long lasting effects. |
| Precautionary statements | Avoid release to the environment. Dispose of contents to local/regional/national/international regulation. Dispose of container to local/regional/national/international regulation. |
4. AUTHORISED USE(S) OF THE META SPC 8
4.1. Use description
Table 28. Use # 1 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual dipping
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual dipping using a dip cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.1.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the dip cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After milking, squeeze the reservoir and put the dip cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Refill the cup of the dipping unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and dip cup by rinsing with water.
4.1.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 29. Use # 2 — Teat disinfection of milkable animals: Post-milking teat disinfection by automated dipping
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Automated dipping |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.2.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product and insert a suction tube of the automated dipping-system. Avoid discharge of surplus fluids.
After milking, the vacuum is shut off and the teat dip is injected into a manifold on the clawpiece. The teats are coated with ca. 5 mL of dip when the teat cup is withdrawn by the Automatic Cluster Removal (ACR). After the removal of the ACR, every liner of the automated dipping-system is thoroughly rinsed with water and blown out with compressed air.
In a final cleaning step after each milking session of the herd, the liners are disinfected (e.g. with a chlorine-based product) and blown out again with compressed air.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
Afterwards, the milking system is ready for the next milking event.
The whole process is automated.
4.2.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
5. GENERAL DIRECTIONS FOR USE 11 OF THE META SPC 8
5.1. Instructions for use
See use specific instructions for use.
5.2. Risk mitigation measures
See use specific risk mitigation measures.
5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
Mentioned in the MSDS
Description of first aid measures
After inhalation: Supply fresh air; consult doctor in case of symptoms.
After skin contact: Wash with water and soap. If skin irritation continues, consult a doctor.
After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult doctor.
After swallowing: Rinse out mouth and then drink plenty of water. Seek medical treatment.
Stability and reactivity
Reactivity: No further relevant information available.
Chemical stability/thermal decomposition/conditions to be avoided: No decomposition if used according to specifications.
Possibility of hazardous reactions: No dangerous reactions known.
Conditions to avoid: No further relevant information available.
Incompatible materials: No further relevant information available.
Hazardous decomposition products: iodine (when warming up).
Accidental release measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Environmental precautions: Do not allow product to reach sewage systems or water bodies in great quantities.
Methods and material for containment and cleaning up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binder). Do not use combustible material like sawdust. Dispose of the material collected according to regulations.
5.4. Instructions for safe disposal of the product and its packaging
Mentioned in the MSDS
Waste treatment methods
Recommendation: Must be specially treated with regard to official regulations.
Waste disposal key number: Corresponding to the regulation of the European Waste catalogue the relation of the waste key numbers has to be made specific to industry and process.
European waste catalogue: Corresponding to the regulation of the EWC the relation of the waste key numbers has to be made specific to industry and process.
At the end of the treatment, dispose unused product and the packaging in accordance with local requirements. Used product can be flushed to the municipal sewer or disposed to the manure deposit depending on local requirements. Avoid release to an individual waste water treatment plant.
5.5. Conditions of storage and shelf-life of the product under normal conditions of storage
Shelf-life: 24 months
Products need to be protected from frost, stored at temperatures not exceeding 30 °C and away from direct sunlight.
6. OTHER INFORMATION
—
7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 8
7.1. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | calgodip D 3000 Film Jod-Dip F 30 Jod Dipp 30 Film (Technolit) Jod 30 Film (Iwetec) Dip es barriere 3000 Lerapur Dip Jod 30 BaktoStop barrier color 3.0 | calgodip D 3000 Film Jod-Dip F 30 Jod Dipp 30 Film (Technolit) Jod 30 Film (Iwetec) Dip es barriere 3000 Lerapur Dip Jod 30 BaktoStop barrier color 3.0 | calgodip D 3000 Film Jod-Dip F 30 Jod Dipp 30 Film (Technolit) Jod 30 Film (Iwetec) Dip es barriere 3000 Lerapur Dip Jod 30 BaktoStop barrier color 3.0 | calgodip D 3000 Film Jod-Dip F 30 Jod Dipp 30 Film (Technolit) Jod 30 Film (Iwetec) Dip es barriere 3000 Lerapur Dip Jod 30 BaktoStop barrier color 3.0 | calgodip D 3000 Film Jod-Dip F 30 Jod Dipp 30 Film (Technolit) Jod 30 Film (Iwetec) Dip es barriere 3000 Lerapur Dip Jod 30 BaktoStop barrier color 3.0 |
| Authorisation number | EU-0018724-0009 1-8 | EU-0018724-0009 1-8 | EU-0018724-0009 1-8 | EU-0018724-0009 1-8 | EU-0018724-0009 1-8 |
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0,34 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 0 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0,26 |
7.2. Trade name(s), authorisation number and specific composition of each individual product
| Trade name(s) | calgodip D 5000 Jod Dip F 50 Jod Dipp 50 (Iwetec) Jod-Dipp 50 (Technolit) Dip es barriere 5000 BaktoStop barrier 5.0 | calgodip D 5000 Jod Dip F 50 Jod Dipp 50 (Iwetec) Jod-Dipp 50 (Technolit) Dip es barriere 5000 BaktoStop barrier 5.0 | calgodip D 5000 Jod Dip F 50 Jod Dipp 50 (Iwetec) Jod-Dipp 50 (Technolit) Dip es barriere 5000 BaktoStop barrier 5.0 | calgodip D 5000 Jod Dip F 50 Jod Dipp 50 (Iwetec) Jod-Dipp 50 (Technolit) Dip es barriere 5000 BaktoStop barrier 5.0 | calgodip D 5000 Jod Dip F 50 Jod Dipp 50 (Iwetec) Jod-Dipp 50 (Technolit) Dip es barriere 5000 BaktoStop barrier 5.0 |
| Authorisation number | EU-0018724-0010 1-8 | EU-0018724-0010 1-8 | EU-0018724-0010 1-8 | EU-0018724-0010 1-8 | EU-0018724-0010 1-8 |
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0,54 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 0 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0,26 |
META SPC 9
1. META SPC 9 ADMINISTRATIVE INFORMATION
1.1. Meta SPC 9 identifier
| Identifier | meta SPC 9 |
1.2. Suffix to the authorisation number
| Number | 1-9 |
1.3. Product type(s)
| Product type(s) | PT03 — Veterinary hygiene (Disinfectants) |
|---|---|
2. META SPC 9 COMPOSITION
2.1. Qualitative and quantitative information on the composition of the meta SPC 9
| Common name | IUPAC name | Function | CAS number | EC number | Content (%) | Content (%) |
|---|---|---|---|---|---|---|
| Common name | IUPAC name | Function | CAS number | EC number | Min | Max |
| Iodine | Active Substance | 7553-56-2 | 231-442-4 | 0,34 | 0,34 | |
| Polyvinylpyrrolidone iodine | Active Substance | 25655-41-8 | 0 | 0 | ||
| Acetic acid | Acetic acid | Non active substance | 64-19-7 | 200-580-7 | 0,11 | 0,33 |
2.2. Type(s) of formulation of the meta SPC 9
| Formulation | AL — Any other liquid |
|---|---|
3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 9
| Hazard statements | Harmful to aquatic life with long lasting effects. |
| Precautionary statements | Avoid release to the environment. Dispose of contents to local/regional/national/international regulation. Dispose of container to local/regional/national/international regulation. |
4. AUTHORISED USE(S) OF THE META SPC 9
4.1. Use description
Table 30. Use # 1 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual dipping
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual dipping using a dip cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.1.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the dip cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking. After milking, squeeze the reservoir and put the dip cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Refill the cup of the dipping unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and dip cup by rinsing with water.
4.1.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.2. Use description
Table 31. Use # 2 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual foaming
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual foaming using a foam cup |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.2.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the foam cup on top. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After milking, squeeze the reservoir and put the foam cup over each teat from below making sure that about 3 cm of the teat are immersed into the disinfectant.
Refill the cup of the foaming unit with fresh disinfectant by squeezing the reservoir as needed. Refill the reservoir with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and foam cup by rinsing with water.
4.2.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.3. Use description
Table 32. Use # 3 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual spraying using a trigger sprayer
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual spraying using a trigger sprayer |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.3.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
The use of a dosing pump for filling the product into the application equipment is recommended.
Fill the reservoir with the RTU product assuming 5 mL product per cow and screw the top of the trigger sprayer on it. Avoid discharge of surplus fluids.
Clean the teats carefully by wiping with a single service paper towel/cloth immediately before milking.
After milking, spray the disinfectant on the teats using the trigger sprayer making sure that about 3 cm of the teat around the streak canal are covered with the disinfectant.
Refill the reservoir of the trigger sprayer with fresh disinfectant as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, empty the reservoir and clean reservoir and trigger sprayer by rinsing with water.
4.3.2. Use-specific risk mitigation measures
Use chemical resistant gloves (glove material to be specified by the authorisation holder within the product information), coverall and chemical resistant boots during post-milking teat disinfection by manual spraying using a trigger sprayer.
Avoid working in spray mist.
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.4. Use description
Table 33. Use # 4 — Teat disinfection of milkable animals: Post-milking teat disinfection by manual spraying using an electronic sprayer
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Manual spraying using an electronic sprayer |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.4.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product assuming 5 mL product per cow and insert a sucking lance of the electronic sprayer. Avoid discharge of surplus fluids.
Clean carefully the teats by wiping with a single service paper towel/cloth before milking.
After milking, spray the disinfectant on the teats using the electronic sprayer making sure that about 3 cm of the teat around the streak canal are covered with the disinfectant.
Replace the empty can by a new can containing the RTU product as needed.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
After disinfection, put the sucking lance system into a bucket of water and rinse the sprayer by pumping the water through the sprayer.
4.4.2. Use-specific risk mitigation measures
Use chemical resistant gloves (glove material to be specified by the authorisation holder within the product information) during post-milking teat disinfection by manual spraying using an electronic sprayer.
Avoid working in spray mist.
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.5. Use description
Table 34. Use # 5 — Teat disinfection of milkable animals: Post-milking teat disinfection by automated dipping
| Product Type | PT03 — Veterinary hygiene (Disinfectants) |
| Where relevant, an exact description of the authorised use | — |
| Target organism(s) (including development stage) | Bacteria Yeasts |
| Field(s) of use | Indoor Teat disinfection for milkable animals (dairy cows) for use after milking |
| Application method(s) | Automated dipping |
| Application rate(s) and frequency | Cows: 5 mL per treatment Post-milking application: 2-3×/day (after each milking) |
| Category(ies) of users | Professional |
| Pack sizes and packaging material | Jerrycan (HDPE): 5 – 60 kg Drum (HDPE): 60 – 200 kg IBC (HDPE): 600 – 1 000 kg |
4.5.1. Use-specific instructions for use
The product must be brought to a temperature above 20 °C before use.
Open a can containing the RTU product and insert a suction tube of the automated dipping-system. Avoid discharge of surplus fluids.
After milking, the vacuum is shut off and the teat dip is injected into a manifold on the clawpiece. The teats are coated with ca. 5 mL of dip when the teat cup is withdrawn by the Automatic Cluster Removal (ACR). After the removal of the ACR, every liner of the automated dipping-system is thoroughly rinsed with water and blown out with compressed air.
In a final cleaning step after each milking session of the herd, the liners are disinfected (e.g. with a chlorine-based product) and blown out again with compressed air.
Leave the product on the teats until next milking. Keep the animals standing for at least 5 minutes after treatment.
Afterwards, the milking system is ready for the next milking event.
The whole process is automated.
4.5.2. Use-specific risk mitigation measures
In case a combination of pre- and post-milking disinfection is necessary, using another product not containing iodine has to be considered for pre-milking disinfection.
4.5.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment
See general directions for use.
4.5.4. Where specific to the use, the instructions for safe disposal of the product and its packaging
See general directions for use.
4.5.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage
See general directions for use.
4.6. Use description
Table 35. Use # 6 — Teat disinfection of milkable animals: Post-milking teat disinfection by automated foaming
Reading this document does not replace reading the official text published in the Official Journal of the European Union. We assume no responsibility for any inaccuracies arising from the conversion of the original to this format.
This text is published under EUR-Lex's own terms of reuse, not a Legalize or public-domain licence.
EUR-Lex
Creative Commons Attribution 4.0 International (CC BY 4.0)
© European Union, https://eur-lex.europa.eu — Source: EUR-Lex (Publications Office of the European Union). Reused under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Only EU legislation published in the printed Official Journal of the European Union is deemed authentic; consolidated texts are reproduced here for documentation purposes and have been reformatted to Markdown.