The Ecodesign for Energy-Related Products and Energy Information (Amendment) Regulations 2021

Made: 27th September 2021

Coming into force in accordance with regulation 1

For the purposes of Article 11(1) of the Framework Regulation, the Secretary of State considers that the conditions set out in Article 11(1)(a) to (d) are satisfied. The Secretary of State has complied with Article 11(2) of that Regulation.

PART 1 — INTRODUCTION

Citation, commencement and extent

1

• (1) These Regulations may be cited as the Ecodesign for Energy-Related Products and Energy Information (Amendment) Regulations 2021.

• (2) Subject to paragraphs (3) and (4), these Regulations come into force on 1st October 2021.

• (3) Regulation 6(6)(a)(iv) comes into force on 1st March 2022 in so far as it inserts the row beginning “Light source parameters” and the two rows after it into Table 6 of Annex 5 to Commission Delegated Regulation (EU) 2019/2016.

• (4) Regulation 8(2)(b) comes into force on 1st January 2022 in so far as it amends the entry relating to a solid fuel local space heater in the table in paragraph 4 of Schedule 1 to the Ecodesign for Energy-Related Products Regulations 2010[^f00003].

• (5) These Regulations extend to England and Wales, and Scotland.

Interpretation

2

In regulations 1 and 6, “Commission Delegated Regulation (EU) 2019/2016” means Commission Delegated Regulation (EU) 2019/2016 of 11 March 2019 supplementing Regulation (EU) 2017/1369 of the European Parliament and of the Council with regard to energy labelling of refrigerating appliances and repealing Commission Delegated Regulation (EU) No 1060/2010[^f00004], as modified by Schedule 3 to the Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020[^f00005].

PART 2 — AMENDMENTS TO COMMISSION REGULATION (EU) 2019/424 RELATED TO ECODESIGN

Amendments to Commission Regulation (EU) 2019/424: servers and data storage products

3

• (1) Commission Regulation (EU) 2019/424 of 15 March 2019 laying down eco-design requirements for servers and data storage products pursuant to Directive 2009/125/EC of the European Parliament and of the Council and amending Commission Regulation (EU) No 617/2013[^f00006] is amended as follows.

• (2) In Article 4(2) (conformity assessment), for the words after “shall contain” substitute—

— (a) the information set out in point 3.4 of Annex 2; and (b) the details and results of the calculations carried out in accordance with— (i) where applicable, point 2 of Annex 2; and (ii) Annex 3 (measurements and calculations).

• (3) In Article 6 (circumvention)—

• (a) for “manufacturer or importer” substitute “manufacturer, importer or authorised representative[^f00007]”;

• (b) after “the parameters” omit “declared by the manufacturer or importer”.

• (4) After Article 7 (indicative benchmarks), insert—

(1) The Secretary of State must, before 25th December 2024— (a) evaluate this Regulation, taking into account the speed of technological progress; and (b) publish a report stating whether or not in their opinion this Regulation should be amended. (2) If the Secretary of State concludes under paragraph (1) that this Regulation should not be amended, the Secretary of State must review this conclusion from time to time and publish a new report under paragraph (1)(b) at intervals not exceeding 5 years.

• (5) In Annex 1 (definitions applicable to Annexes 2 to 5)—

• (a) in point (3) (definition of ‘motherboard’), for “the server” substitute “a server or a data storage product”;

• (b) in point (4) (definition of ‘processor’), after “a server” insert “or a data storage product”;

• (c) in point (5) (definition of ‘memory’), after “a server” insert “or a data storage product”;

• (d) after point (35) insert—

(36) ‘declared values’ means the values provided by the manufacturer, importer or authorised representative in the technical documentation in accordance with point 3.4 of Annex 2, for the verification of conformity by the market surveillance authority[^f00008].

• (6) In Annex 4 (verification procedure for market surveillance purposes)—

• (a) for the first paragraph substitute—

The verification tolerances set out in this Annex relate only to the verification by the market surveillance authority of the declared values. The manufacturer, importer or authorised representative of a product must not use the verification tolerances— (a) to establish the declared values; (b) to interpret the declared values; or (c) to communicate better performance.

• (b) in point 2—

• (i) in point (a), for “values given in the technical documentation pursuant to paragraph 1(2)(b) of Part 1 of Schedule 1A to the 2010 Regulations,” substitute “declared values”;

• (ii) after point (c) insert—

; and (d) the manufacturer, importer or authorised representative has complied with the information requirements in point 3.1 of Annex 2 (servers) or, as the case may be, point 3.2 of Annex 2 (data storage products); and (e) when the market surveillance authority checks the unit of the model, the unit complies with the resource efficiency requirements in point 3.3 of Annex 2.

• (c) in point 3, for “points 2(a) or 2(b)” substitute “point (2)(a), (b), (d) or (e)”;

• (d) in point 4(b), after “manufacturer” insert “, importer or authorised representative”;

• (e) in point 5, for “these three units” substitute “the units selected in accordance with point 4(b)”;

• (f) in point 6, for “point 4(b)” substitute “point 5”.

PART 3 — AMENDMENTS TO COMMISION DELEGATED REGULATIONS RELATED TO ENERGY LABELLING

Amendments to Commission Delegated Regulation (EU) 2019/2013: electronic displays

4

• (1) Commission Delegated Regulation (EU) 2019/2013 of 11 March 2019 supplementing Regulation (EU) 2017/1369 of the European Parliament and of the Council with regard to energy labelling of electronic displays and repealing Commission Delegated Regulation (EU) No 1062/2010[^f00009], as modified by Schedule 1 to the Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020, is amended as follows.

• (2) In Article 1(2) (subject matter and scope), in point (g), for “of products covered by implementing measures adopted under the Ecodesign for Energy-Related Products Regulations 2010” substitute “within the meaning given by regulation 2(1) of the Ecodesign for Energy-Related Products Regulations 2010”.

• (3) In Article 2 (definitions)—

• (a) in point (10), for “as defined in Article 1” substitute “and is to be construed in accordance with the definitions of ‘networked equipment with high network availability’ and ‘networked equipment with high network availability functionality’ in Article 2”;

• (b) omit point (17).

• (4) In Article 3(1) (obligations of suppliers), for point (b) substitute—

(b) the information set out in table 4 of Annex 5 (product information sheet) is made available on a publicly accessible website;

• (5) In Annex 1 (definitions for the purposes of the Annexes), after point (28) insert—

(29) ‘declared values’ means the values provided by the supplier in the technical documentation in accordance with point (4) of Annex 6 for the verification of conformity by the market surveillance authority; (30) ‘guarantee’ means any undertaking by the dealer or the supplier to the consumer that, if an electronic display does not meet the specifications set out in the guarantee statement or in any associated advertising— (a) the consumer will be reimbursed for the price paid for the electronic display; or (b) the electronic display will be repaired, replaced or handled in any way.

• (6) In Annex 2, in point B (energy efficiency index)—

• (a) after the formula, in the explanation of term “A” in the formula, for “viewing surface area” substitute “visible screen area”;

• (b) after the explanation of term “corr₁” in the formula, insert—

For the purposes of the EEI calculation, the declared values of the following technical parameters listed in Table 5 of Annex 6 (technical documentation) must be used— (a) on mode power demand (Pmeasured ); (b) visible screen area.

• (7) In Annex 3, in point 2 (label design)—

• (a) at the beginning of point (f) insert “Subject to point (g)”;

• (b) after point (f) insert—

(g) If the electronic display does not support HDR— (i) the following must not be displayed— (aa) the HDR pictogram; and (bb) the energy efficiency class; and (ii) the screen pictogram, indicating screen size and resolution, must be vertically centred in the area below the indication of the energy consumption.

• (8) In Annex 5 (product information sheet)—

• (a) number the first paragraph as paragraph 1;

• (b) number the second paragraph as paragraph 2;

• (c) for Table 4 substitute—

	Parameter	Parameter	Value	Value	Value	Unit	Notes
1.	Supplier’s name or trade mark	Supplier’s name or trade mark				TEXT
2.	Supplier’s address	Supplier’s address
3.	Model identifier	Model identifier				TEXT
4.	Energy efficiency class for standard Dynamic Range (SDR)	Energy efficiency class for standard Dynamic Range (SDR)	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
5.	On mode power demand in Standard Dynamic Range (SDR)	On mode power demand in Standard Dynamic Range (SDR)	X.X	X.X	X.X	W	Rounded to the nearest decimal place for power values below 100 W and rounded to the nearest integer for power values equal to or above 100 W.
6.	Energy Efficiency class (HRD)	Energy Efficiency class (HRD)	[A/B/C/D/E/F/G] or n.a.	[A/B/C/D/E/F/G] or n.a.	[A/B/C/D/E/F/G] or n.a.		Value must be ‘n.a.’ (not applicable) if HDR is not implemented.
7.	On mode power demand in High Dynamic Range (HDR)	On mode power demand in High Dynamic Range (HDR)	X.X	X.X	X.X	W	Rounded to the nearest decimal place for power values below 100 W and rounded to the nearest integer for power values equal to or above 100 W. Value is 0 (zero) if HRD is not implemented.
8.	Off mode, power demand, if applicable	Off mode, power demand, if applicable	X.X	X.X	X.X	W
9.	Standby mode power demand, if applicable	Standby mode power demand, if applicable	X.X	X.X	X.X	W
10.	Networked standby mode power demand, if applicable	Networked standby mode power demand, if applicable	X.X	X.X	X.X	W
11.	Electronic display category	Electronic display category	[television/monitor/ signage/other]	[television/monitor/ signage/other]	[television/monitor/ signage/other]		Select one.
12.	Size ratio	Size ratio	X	:	Y	integer	For example 16:9. 21:9, etc.
13.	Screen resolution	Screen resolution	X	×	Y	pixels	Horizontal and vertical pixels.
14.	Screen diagonal	Screen diagonal	X.X	X.X	X.X	cm	Rounded to one decimal place.
15.	Screen diagonal	Screen diagonal	X	X	X	inches	Optional, in inches rounded to the nearest integer.
16.	Visible screen area	Visible screen area	X.X	X.X	X.X	dm²	Rounded to one decimal place.
17.	Panel technology used	Panel technology used	TEXT	TEXT	TEXT		E.g. LCD/LED LCD/QLED LCD/OLED/MicroLED/ QDLED/SED/FED/EPD, etc.
18.	Availability of Automatic Brightness Control (ABC)	Availability of Automatic Brightness Control (ABC)	[YES/NO]	[YES/NO]	[YES/NO]
19.	Availability of voice recognition sensor	Availability of voice recognition sensor	[YES/NO]	[YES/NO]	[YES/NO]
20.	Availability of room presence sensor	Availability of room presence sensor	[YES/NO]	[YES/NO]	[YES/NO]
21.	Image refresh frequency rate (default)	Image refresh frequency rate (default)	X	X	X	Hz
22.	Minimum guaranteed availability of software and firmware updates	Minimum guaranteed availability of software and firmware updates	X	X	X	Years
23.	Minimum guaranteed availability of spare parts	Minimum guaranteed availability of spare parts	X	X	X	Years
24.	Minimum guaranteed product support	Minimum guaranteed product support	X	X	X	Years
25.	Minimum duration of the guarantee given by the supplier	Minimum duration of the guarantee given by the supplier	X	X	X	Years
26.	Power supply type	Power supply type	Internal / External / Standardised external	Internal / External / Standardised external	Internal / External / Standardised external		Select one.
27.	External power supply (non-standardized and included in the product box)	External power supply (non-standardized and included in the product box)	External power supply (non-standardized and included in the product box)	External power supply (non-standardized and included in the product box)	External power supply (non-standardized and included in the product box)	External power supply (non-standardized and included in the product box)	External power supply (non-standardized and included in the product box)
27.	i	Supported standard name or list	Supported standard name or list	Supported standard name or list	Supported standard name or list	TEXT	Description
27.	ii	Input voltage	X	X	X	V
27.	iii	Output voltage	X.X	X.X	X.X	V
28.	External standardised power supply (or suitable one if not included in the product box)	External standardised power supply (or suitable one if not included in the product box)	External standardised power supply (or suitable one if not included in the product box)	External standardised power supply (or suitable one if not included in the product box)	External standardised power supply (or suitable one if not included in the product box)	External standardised power supply (or suitable one if not included in the product box)	External standardised power supply (or suitable one if not included in the product box)
28.	i	Supported standard name or list	Supported standard name or list	Supported standard name or list	Supported standard name or list	TEXT
28.	ii	Required output voltage	X.X	X.X	X.X	V
28.	Iii	Required delivered current (minimum)	X.X	X.X	X.X	A
28.	iv	Required current frequency	X.X	X.X	X.X	Hz

• (d) after Table 4 insert—

(3) The following items in Table 4 are not relevant for the purposes of determining whether a model is an equivalent model under Article 2(6) of the Framework Regulation— (a) supplier’s name or trade mark; (b) supplier’s address; (c) model identifier; (d) minimum guaranteed availability of software and firmware updates; (e) minimum guaranteed availability of spare parts; (f) minimum guaranteed product support; (g) minimum duration of the guarantee given by the supplier.

• (9) In Annex 6 (technical documentation)—

• (a) for points (1) to (5) substitute—

(1) a general description of the model, sufficient for it to be unequivocally and easily identified; (2) references to the designated standards applied or other measurement standards used; (3) specific precautions that must be taken when the model is assembled, installed, maintained or tested; (4) the values of the technical parameters set out in Table 5; (5) the details and the results of the calculations performed in accordance with Annex 4; (5A) the conditions of testing that must be applied, if not fully described in the information provided under point (2); (5B) the identifier of all equivalent models already placed on the market;

• (b) for Table 5 substitute—

	Parameter	Value	Value	Value	Unit	Declared value
General	General	General	General	General	General	General
1	Supplier’s name or trade mark	TEXT	TEXT	TEXT
2	Model identifier	TEXT	TEXT	TEXT
3	On mode power demand, (Pmeasured)	XXX.X	XXX.X	XXX.X	W
4	Energy efficiency class for Standard Dynamic Range (SDR)	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
5	On mode power demand in Standard Dynamic Range (SDR)	XXX.X	XXX.X	XXX.X	W
6	Energy efficiency class for Dynamic Range (HDR)	[A/B/C/D/E/F/G] or n.a.	[A/B/C/D/E/F/G] or n.a.	[A/B/C/D/E/F/G] or n.a.
7	On mode power demand in High Dynamic Range (HDR)	XXX.X	XXX.X	XXX.X	W
8	Off mode, power demand	X.X	X.X	X.X	W
9	Standby mode power demand	X.X	X.X	X.X	W
10	Networked standby mode power demand	X.X	X.X	X.X	W
11	Electronic display category	[television / monitor / signage / other]	[television / monitor / signage / other]	[television / monitor / signage / other]	TEXT
12	Size ratio	XX	:	XX
13	Screen resolution (pixels)	X	×	X
14	Screen diagonal	XXX.X	XXX.X	XXX.X	cm
15	Screen diagonal	XX	XX	XX	inches
16	Visible screen area	XXX.X	XXX.X	XXX.X	dm²;
17	Panel technology used	TEXT	TEXT	TEXT
18	Availability of automatic Brightness Control (ABC)	[YES/NO]	[YES/NO]	[YES/NO]
19	Availability of voice recognition sensor	[YES/NO]	[YES/NO]	[YES/NO]
20	Availability of room presence sensor	[YES/NO]	[YES/NO]	[YES/NO]
21	Image refresh frequency rate (normal configuration)	XXX	XXX	XXX	HZ
22	Minimum guaranteed availability of software and firmware updates	XX	XX	XX	Years
23	Minimum guaranteed availability of spare parts	XX	XX	XX	Years
24	Minimum guaranteed product support	XX	XX	XX	Years
25	Minimum duration of the guarantee given by the supplier	XX	XX	XX	Years
For On-mode	For On-mode	For On-mode	For On-mode	For On-mode	For On-mode	For On-mode
26	Peak white luminance of the brightest on mode configuration	XXXX	XXXX	XXXX	cd/ m²
27	Peak white luminance of the normal configuration	XXXX	XXXX	XXXX	cd/ m²
28	Peak white luminance ratio (calculated as the value of ‘Peak white luminance of the normal configuration’ divided by the value of ‘Peak white luminance of the brightest on mode configuration’ multiplied by 100)	XX.X	XX.X	XX.X	%
For Auto Power Down (APD)	For Auto Power Down (APD)	For Auto Power Down (APD)	For Auto Power Down (APD)	For Auto Power Down (APD)	For Auto Power Down (APD)	For Auto Power Down (APD)
29	Length of time in on mode before the electronic display automatically switches to standby, off mode, or another condition which does not exceed the applicable power demand requirements for off mode or standby mode	XX:XX	XX:XX	XX:XX	mm:ss
30	For televisions: the length of time following the last user interaction before the television automatically switches to standby, off-mode or another condition which does not exceed the applicable power consumption requirements for off-mode or standby-mode	XX:XX	XX:XX	XX:XX	mm:ss
31	For televisions equipped with room presence sensor: the length of time after no presence is detected before the television automatically switches to standby, off-mode or another condition which does not exceed the applicable power demand requirements for off mode or standby mode	XX:XX	XX:XX	XX:XX	mm:ss
32	For electronic displays other than televisions and broadcast displays: the length of time after no input is detected before the electronic display automatically switches to standby, off-mode, or another condition which does not exceed the applicable power consumption requirements for off mode or standby mode	XX:XX	XX:XX	XX:XX	mm:ss
For ABC If available and activated by default	For ABC If available and activated by default	For ABC If available and activated by default	For ABC If available and activated by default	For ABC If available and activated by default	For ABC If available and activated by default	For ABC If available and activated by default
33	Percentage of power reduction due to ABC action between the 100 lux and 12 lux ambient light conditions	XX.X	XX.X	XX.X	%
34	On mode power at 100 lux ambient light at the ABC sensor	XXX.X	XXX.X	XXX.X	W
35	On mode power at 12 lux ambient light at the ABC sensor	XXX.X	XXX.X	XXX.X	W
36	Screen luminance at 100 lux ambient light at the ABC sensor	XXX	XXX	XXX	cd/ m²
37	Screen luminance at 60 lux ambient light at the ABC sensor	XXX	XXX	XXX	cd/ m²
38	Screen luminance at 35 lux ambient light at the ABC sensor	XXX	XXX	XXX	cd/ m²
39	Screen luminance at 12 lux ambient light at the ABC sensor	XXX	XXX	XXX	cd/ m²
For Power Supply	For Power Supply	For Power Supply	For Power Supply	For Power Supply	For Power Supply	For Power Supply
40	Power supply type	Internal/External	Internal/External	Internal/External
41	Standard references (if applicable)				TEXT
42	Input voltage	XXX.X	XXX.X	XXX.X	V
43	Output voltage	XXX.X	XXX.X	XXX.X	V
44	Input current (max)	XXX.X	XXX.X	XXX.X	A
45	Output current (min)	XXX.X	XXX.X	XXX.X	A

• (10) In Annex 9 (verification procedure for market surveillance purposes)—

• (a) for the first paragraph substitute—

The verification tolerances set out in this Annex relate only to the verification by the market surveillance authority of the declared values. The supplier of a product must not use the verification tolerances— (a) as allowed tolerances to establish the declared values; (b) to interpret the declared values; or (c) to communicate better performance. The values and classes published on the label or in the product information sheet must not be more favourable to the supplier than the declared values.

• (b) in point 2—

• (i) in point (a), for “values given in the technical documentation pursuant to point 3 of Article 3 of Regulation (EU) 2017/1369 (declared values)” substitute “declared values”;

• (ii) in point (c), for the words after “comply with” substitute—

(i) in the case of the determined values of the ABC luminance-related parameters (see rows 36 to 39 of Table 5 of Annex 6), the requirements in point (e) of point C of Annex 2; and (ii) otherwise, the respective verification tolerances set out in Table 6.

• (c) for point (3) substitute—

(3) The model and all equivalent models must be considered not to comply with this Regulation if— (a) the result referred to in point 2(a), (b) or (c)(i) is not achieved; or (b) the determined value of a parameter listed in rows 3 to 5 or 7 to 10 of Table 6 does not comply with the applicable verification tolerance set out in Table 6.

• (d) in point (4), for “If the result referred to in point 2(c) is not achieved” substitute “If the determined value of a parameter listed in row 1, 2 or 6 of Table 6 does not comply with the respective verification tolerance set out in Table 6 (so that the result referred to in point 2(c) is not achieved)”;

• (e) in the final paragraph before Table 6, for “points 1 to 7” substitute “points 1 to 6”;

• (f) for Table 6 substitute—

	Parameter	Verification tolerances
1.	On mode power demand, (Pmeasured, Watts)	The determined value must not exceed the declared value by more than 7 %.
2.	Off mode, standby mode and networked standby mode power demand (Watts), as applicable	The determined valuemust not exceed the declared value by more than 0.10 Watt if the declared value is 1.00 W or less, or by more than 10% if the declared value is more than 1.00 W.
3.	Visible screen area	The determined value must not be lower than the declared value by more than whichever is the smaller of 1 % or 0.1 dm².
4.	Visible screen diagonal in centimetres	The determined valuemust not differ from the declared value by more than 1cm.
5.	The screen resolution in horizontal and vertical pixels	The determined value must not differ from the declared value.
6.	Peak white luminance	The determined valuemust not be lower than the declared value by more than 8%.
7.	Length of time in on mode before the electronic display automatically switches to standby, off mode or another condition which does not exceed the applicable power demand requirements for off mode or standby mode	The determined value must not exceed the declared value by more than 5 seconds.
8.	For televisions: the length of time after the last user interaction before the television automatically switches to standby, off-mode, or another condition which does not exceed the applicable power consumption requirements for off mode or standby mode	The determined value must not exceed the declared value by more than 5 seconds.
9.	For televisions equipped with room presence sensor: the length of time after no presence is detected before the television automatically switches to standby, off-mode, or another condition which does not exceed the applicable power demand requirements for off mode or standby mode	The determined value must not exceed the declared value by more than 5 seconds.
10.	For electronic displays other than televisions and broadcast displays: the length of time after no input is detected before the electronic display automatically switches to standby, off-mode or another condition which does not exceed the applicable power consumption requirements for off mode or standby mode	The determined value must not exceed the declared value by more than 5 seconds.

Amendments to Commission Delegated Regulation (EU) 2019/2014: household washing machines and washer-dryers

5

• (1) Commission Delegated Regulation (EU) 2019/2014 of 11 March 2019 supplementing Regulation (EU) 2017/1369 of the European Parliament and of the Council with regard to energy labelling of household washing machines and household washer-dryers and repealing Commission Delegated Regulation (EU) No 1061/2010 and Commission Directive 96/60/EC[^f00010], as modified by Schedule 2 to the Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020, is amended as follows.

• (2) In Article 3(1) (obligations of suppliers), for point (b) substitute—

(b) the information set out in Table 5 of Annex 5 (product information sheet for household washing machines) or, as the case may be, Table 6 of Annex 5 (product information sheet for household washer-dryers) is made available on a publicly accessible website;

• (3) In Annex 1 (definitions applicable for the Annexes), after point (32) insert—

(33) ‘declared values’ means the values provided by the supplier in the technical documentation in accordance with point 1(d) of Annex 6 (household washing machines) or point 2(d) of Annex 6 (household washer-dryers) for the verification of conformity by the market surveillance authority; (34) ‘wash and dry cycle’ means a complete cycle for cotton laundry— (a) which is continuous if the household washer-dryer provides a continuous cycle; (b) where the washing cycle is the eco 40-60 programme; and (c) where the drying cycle achieves cupboard dry status.

• (4) In Annex 4 (measurement methods and calculations)—

• (a) after the first paragraph insert—

Where a calculation in this Annex uses a parameter listed in Table 7 of Annex 6 (technical documentation for household washing machines) or Table 8 of Annex 6 (technical documentation for household washer-dryers), the supplier must use the declared value for that parameter.

• (b) in point 1 (rated capacity of household washer-dryers), in the first sentence, for “shall be measured, using” substitute “is the rated capacity of”;

• (c) in point 3 (washing efficiency index)—

• (i) in the existing paragraph, for “two decimal places” substitute “three decimal places”;

• (ii) after the existing paragraph, insert as a paragraph—

For household washing machines with a rated capacity higher than 3 kg and for the washing cycle of household washer-dryers with a rated washing capacity higher than 3 kg, the value to be entered on the Product Information sheet for IW is the lowest of the values for— (a) the washing efficiency index at the rated washing capacity; (b) the washing efficiency index at half of the rated washing capacity; and (c) the washing efficiency index at quarter of the rated washing capacity. For household washing machines with a rated capacity lower than or equal to 3 kg and for the washing cycle of household washer-dryers with a rated capacity lower than or equal to 3 kg, the value to be entered on the Product Information Sheet for IW is the value for the washing efficiency index at the rated washing capacity. For household washer-dryers with a rated capacity higher than 3 kg, the value to be entered on the Product Information sheet for JW is the lower of the values for— (a) the washing efficiency index at the rated capacity; and (b) the washing efficiency index at half of the rated capacity. For household washer-dryers with a rated capacity lower than or equal to 3 kg, the value to be entered on the Product Information Sheet for JW is the value for the washing efficiency index at the rated capacity.

• (d) in point 4 (rinsing effectiveness), after the existing paragraph insert—

For household washing machines with a rated capacity higher than 3 kg and for the washing cycle of household washer-dryers with a rated capacity higher than 3 kg, the value to be entered on the Product Information Sheet for the IR is the highest of the values for— (a) the rinsing effectiveness at rated washing capacity; (b) the rinsing effectiveness at half of the rated washing capacity; and (c) the rinsing effectiveness at quarter of the rated washing capacity. For household washing machines with a rated capacity lower than or equal to 3 kg and for the washing cycle of household washer-dryers with a rated capacity lower than or equal to 3 kg, no value is to be entered on the Product Information Sheet for IR. For household washer-dryers with a rated capacity higher than 3 kg, the value to be entered on the Product Information Sheet for JR is the higher of the values for— (a) the rinsing effectiveness index at the rated capacity; and (b) the rinsing effectiveness index at half of the rated capacity. For household washer-dryers with a rated capacity lower than or equal to 3 kg, no value is to be indicated on the Product Information sheet for JR.

• (e) in point 6(2) (weighted water consumption), in the first paragraph, after “weighted water consumption” insert “of the wash and dry cycle”;

• (f) in point 7 (remaining moisture content)—

• (i) in the first paragraph, for “the nearest whole percent” substitute “one decimal place”;

• (ii) after the formula, in the explanations of the terms used in the equation, in each place that it occurs, for “one decimal place” substitute “two decimal places”.

• (g) in point 9 (low power modes)—

• (i) in the first paragraph—

• (aa) at the beginning, insert “Where applicable,”;

• (bb) after “(Psm) and” omit “where applicable”;

• (ii) in the third paragraph, for “energy consumption” substitute “the power consumption”;

• (h) after point 10 (acoustic airborne noise emission), insert—

(11) The spin speed of a household washing machine and of the washing cycle of a household washer-dryer must be measured or calculated at the highest spin speed option for the eco 40-60 programme and rounded to the nearest integer.

• (5) In Annex 5 (product information sheet)—

• (a) in point 1 (household washing machines)—

• (i) number the first paragraph as point (1);

• (ii) number the second paragraph as point (2);

• (iii) for Table 5 substitute—

(1) for the eco 40-60 programme	(1) for the eco 40-60 programme	(1) for the eco 40-60 programme	(1) for the eco 40-60 programme	(1) for the eco 40-60 programme	(1) for the eco 40-60 programme	(1) for the eco 40-60 programme
Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:
Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:
Model identifier:	Model identifier:	Model identifier:	Model identifier:	Model identifier:	Model identifier:	Model identifier:
General product parameters:	General product parameters:	General product parameters:	General product parameters:	General product parameters:	General product parameters:	General product parameters:
Parameter	Value	Value	Parameter	Value	Value	Value
Rated capacity (kg)[^f01000]	x.x	x.x	Dimensions in cm[^f01000]	Height	Height	x
Rated capacity (kg)[^f01000]	x.x	x.x	Dimensions in cm[^f01000]	Width	Width	x
Rated capacity (kg)[^f01000]	x.x	x.x	Dimensions in cm[^f01000]	Depth	Depth	x
Energy efficiency index (EEIW)[^f01000]	x.x	x.x	Energy efficiency class[^f01000]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
Washing efficiency index[^f01000]	x.xxx	x.xxx	Rinsing effectiveness (g/kg)[^f01000]	x.x	x.x	x.x
Energy consumption in kWh per cycle, based on the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used.	Rated capacity	x.xxx	Water consumption in litre per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Rated capacity	x	x
Energy consumption in kWh per cycle, based on the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used.	Half	x.xxx	Water consumption in litre per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Half	x	x
Energy consumption in kWh per cycle, based on the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used.	Quarter	x.xxx	Water consumption in litre per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Quarter	x	x
Maximum temperature inside the treated textile (°C)[^f01000]	Rated capacity	x	Weighted remaining moisture content (%)[^f01000]	x.x	x.x	x.x
Maximum temperature inside the treated textile (°C)[^f01000]	Half	x	Weighted remaining moisture content (%)[^f01000]	x.x	x.x	x.x
Maximum temperature inside the treated textile (°C)[^f01000]	Quarter	x	Weighted remaining moisture content (%)[^f01000]	x.x	x.x	x.x
Spin speed (rpm)[^f01000]	Rated capacity	x	Spin-drying efficiency class[^f01000]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
Spin speed (rpm)[^f01000]	Half	x	Spin-drying efficiency class[^f01000]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
Spin speed (rpm)[^f01000]	Quarter	x	Spin-drying efficiency class[^f01000]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
Programme duration (h:min)[^f01000]	Rated capacity	x:xx	Type	[built-in/free-standing]	[built-in/free-standing]	[built-in/free-standing]
Programme duration (h:min)[^f01000]	Half	x:xx	Type	[built-in/free-standing]	[built-in/free-standing]	[built-in/free-standing]
Programme duration (h:min)[^f01000]	Quarter	x:xx	Type	[built-in/free-standing]	[built-in/free-standing]	[built-in/free-standing]
Airborne acoustical noise emissions during the spinning phase (dB(A) re 1 pW)[^f01000]	x	x	Airborne acoustical noise emission class (spinning phase)[^f01000]	[A/B/C/D]	[A/B/C/D]	[A/B/C/D]
Off-mode (W) (if applicable)	x.xx	x.xx	Standby mode (if applicable)	x.xx	x.xx	x.xx
Delay start (W) (if applicable)	x.xx	x.xx	Networked standby (W) (if applicable)	x.xx	x.xx	x.xx
Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:
This product has been designed to release silver ions during the washing cycle	This product has been designed to release silver ions during the washing cycle	This product has been designed to release silver ions during the washing cycle	[YES/NO]	[YES/NO]	[YES/NO]	[YES/NO]
Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:

• (iv) after Table 5, insert—

(3) The following items in Table 5 are not relevant for the purposes of determining whether a model is an equivalent model under Article 2(6) of the Framework Regulation— (a) supplier’s name or trade mark; (b) supplier’s address; (c) model identifier; (d) dimensions in cm; (e) minimum duration of the guarantee given by the supplier; (f) additional information.

• (b) in point 2 (household washer-dryers)—

• (i) number the first paragraph as point (1);

• (ii) number the second paragraph as point (2);

• (iii) for Table 6 substitute—

(1) for the wash and dry cycle	(1) for the wash and dry cycle	(1) for the wash and dry cycle	(1) for the wash and dry cycle	(1) for the wash and dry cycle	(1) for the wash and dry cycle	(1) for the wash and dry cycle
(2) for the eco 40-60 programme	(2) for the eco 40-60 programme	(2) for the eco 40-60 programme	(2) for the eco 40-60 programme	(2) for the eco 40-60 programme	(2) for the eco 40-60 programme	(2) for the eco 40-60 programme
Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:	Supplier’s name or trade mark:
Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:	Supplier’s address:
Model identifier:	Model identifier:	Model identifier:	Model identifier:	Model identifier:	Model identifier:	Model identifier:
General product parameters:	General product parameters:	General product parameters:	General product parameters:	General product parameters:	General product parameters:	General product parameters:
Parameter	Value	Value	Parameter	Value	Value	Value
Rated capacity (kg)	Rated capacity [^f01001]	x.x	Dimensions in cm	Height	Height	x
Rated capacity (kg)	Rated washing capacity [^f01002]	x.x	Dimensions in cm	Width	Width	x
Rated capacity (kg)	Rated washing capacity [^f01002]	x.x	Dimensions in cm	Depth	Depth	x
Energy efficiency index	EEIW[^f01002]	x.x	Energy efficiency class	EEIW[^f01002]	EEIW[^f01002]	[A/B/C/D/E/F/G]
Energy efficiency index	EEIWD[^f01001]	x.x	Energy efficiency class	EEIWD[^f01001]	EEIWD[^f01001]	[A/B/C/D/E/F/G]
Washing efficiency index	IW[^f01002]	x.xxx	Rinsing effectiveness (g/kg)	IR[^f01002]	IR[^f01002]	x.x
Washing efficiency index	JW[^f01001]	x.xxx	Rinsing effectiveness (g/kg)	JR[^f01001]	JR[^f01001]	x.x
Energy consumption in kWh per cycle, for the washing cycle of the household washer-dryer, using the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used.	Rated capacity	x.xxx	Energy consumption in kWh per cycle, for the wash and dry cycle of the household washer-dryer. Actual energy consumption will depend on how the appliance is used.	Rated capacity	x.xxx	x.xxx
Energy consumption in kWh per cycle, for the washing cycle of the household washer-dryer, using the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used.	Half	x.xxx	Energy consumption in kWh per cycle, for the wash and dry cycle of the household washer-dryer. Actual energy consumption will depend on how the appliance is used.	Half	x.xxx	x.xxx
Energy consumption in kWh per cycle, for the washing cycle of the household washer-dryer, using the eco 40-60 programme. Actual energy consumption will depend on how the appliance is used.	Quarter	x.xxx	Energy consumption in kWh per cycle, for the wash and dry cycle of the household washer-dryer. Actual energy consumption will depend on how the appliance is used.	Quarter	x.xxx	x.xxx
Water consumption in litres per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Rated capacity	x	Water consumption in litre per cycle, for the wash and dry cycle of the household washer- dryer. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Rated capacity	x	x
Water consumption in litres per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Half	x	Water consumption in litre per cycle, for the wash and dry cycle of the household washer- dryer. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Half	x	x
Water consumption in litres per cycle, based on the eco 40-60 programme. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Quarter	x	Water consumption in litre per cycle, for the wash and dry cycle of the household washer- dryer. Actual water consumption will depend on how the appliance is used and on the hardness of the water.	Quarter	x	x
Maximum temperature inside the treated textile (°C) for the washing cycle of the household washer-dryer, using the eco 40-60 programme	Rated capacity	x	Maximum temperature inside the treated textile (°C) for the washing cycle of the household washer-dryer, using the wash and dry cycle	Rated capacity	x	x
Maximum temperature inside the treated textile (°C) for the washing cycle of the household washer-dryer, using the eco 40-60 programme	Half	x	Maximum temperature inside the treated textile (°C) for the washing cycle of the household washer-dryer, using the wash and dry cycle	Half	x	x
Maximum temperature inside the treated textile (°C) for the washing cycle of the household washer-dryer, using the eco 40-60 programme	Quarter	x	Maximum temperature inside the treated textile (°C) for the washing cycle of the household washer-dryer, using the wash and dry cycle	Half	x	x
Spin speed (rpm)[^f01002]	Rated capacity	x	Weighted remaining moisture content (%)[^f01002]	x.x	x.x	x.x
Spin speed (rpm)[^f01002]	Half	x	Weighted remaining moisture content (%)[^f01002]	x.x	x.x	x.x
Spin speed (rpm)[^f01002]	Quarter	x	Weighted remaining moisture content (%)[^f01002]	x.x	x.x	x.x
Eco 40-60 Programme duration (h:min)	Rated capacity	x:xx	Spin-drying efficiency class[^f01002]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
Eco 40-60 Programme duration (h:min)	Half	x:xx	Spin-drying efficiency class[^f01002]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
Eco 40-60 Programme duration (h:min)	Quarter	x:xx	Spin-drying efficiency class[^f01002]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]	[A/B/C/D/E/F/G]
Airborne acoustical noise emissions during the spinning phase for the eco 40-60 washing cycle at rated washing capacity (dB(A) re 1 pW)	x	x	wash and dry cycle duration (h:min)	Rated capacity	x:xx	x:xx
Airborne acoustical noise emissions during the spinning phase for the eco 40-60 washing cycle at rated washing capacity (dB(A) re 1 pW)	x	x	wash and dry cycle duration (h:min)	Half	x:xx	x:xx
Type	[built-in/free-standing]	[built-in/free-standing]	Airborne acoustical noise emission class for the spinning phase for the eco 40-60 programme at rated washing capacity	[A/B/C/D]	[A/B/C/D]	[A/B/C/D]
Off-mode (W) (if applicable)	x.xx	x.xx	Standby mode (if applicable)	x.xx	x.xx	x.xx
Delay start (W) (if applicable)	x.xx	x.xx	Networked standby (W) (if applicable)	x.xx	x.xx	x.xx
Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:	Minimum duration of the guarantee given by the supplier:
This product has been designed to release silver ions during the washing cycle	This product has been designed to release silver ions during the washing cycle	This product has been designed to release silver ions during the washing cycle	[YES/NO]	[YES/NO]	[YES/NO]	[YES/NO]
Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:	Additional information: Weblink to the supplier’s website:

• (iv) after Table 6 insert—

(3) The following items in Table 6 are not relevant for the purposes of determining whether a model is an equivalent model under Article 2(6) of the Framework Regulation— (a) supplier’s name or trade mark; (b) supplier’s address; (c) model identifier; (d) dimensions in cm; (e) minimum duration of the guarantee given by the supplier; (f) additional information.

• (6) In Annex 6 (technical documentation), in point 1 (household washing machines)—

• (a) before Table 7, for points (a) and (b) substitute—

(a) a general description of the model, sufficient for it to be unequivocally and easily identified; (b) references to the designated standards applied or other measurement standards used; (c) specific precautions that must be taken when the model is assembled, installed, maintained or tested; (d) the values of the technical parameters set out in Table 7; (e) the details and the results of the calculations performed in accordance with Annex 4; (f) the conditions of testing that must be applied, if not fully described in the information provided under point (b); (g) the model identifier of all equivalent models already placed on the market.

• (b) in Table 7—

• (i) in the third column of the entry relating to each of the following parameters, for “X,XX” substitute “X.XXX”—

• (aa) “Washing efficiency index of the eco 40-60 programme at rated capacity (IW)”;

• (bb) “Washing efficiency index of the eco 40-60 programme at half rated capacity (IW)”;

• (cc) “Washing efficiency index of the eco 40-60 programme at quarter rated capacity (IW)”;

• (ii) omit the entry relating to each of the following parameters—

• (aa) “Remaining moisture content for the eco 40-60 programme at rated capacity (Dfull)”;

• (bb) “Remaining moisture content for the eco 40-60 programme at half capacity (D1/2)”;

• (cc) “Remaining moisture content for the eco 40-60 programme at quarter capacity (D1/4)”;

• (iii) in the third column of the entry relating to “Weighted remaining moisture content”, for “X” substitute “X.X”;

• (iv) in the first column of the entry relating to each of the following parameters, at the end insert “if applicable”—

• (aa) “Power consumption in ‘off mode’ (Po)”;

• (bb) “Power consumption in ‘standby mode’ (Psm)”;

• (v) after Table 7, omit points (c) to (f).

• (7) In Annex 6 (technical documentation), in point 2 (household washing washer-dryers)—

• (a) before Table 8, for points (a) and (b) substitute—

(a) a general description of the model, sufficient for it to be unequivocally and easily identified; (b) references to the designated standards applied or other measurement standards used; (c) specific precautions that must be taken when the model is assembled, installed, maintained or tested; (d) the values of the technical parameters set out in Table 8; (e) the details and the results of the calculations performed in accordance with Annex 4; (f) the conditions of testing that must be applied, if not fully described in the information provided under point (b); (g) the model identifier of all equivalent models already placed on the market.

• (b) in Table 8 (technical documentation for household washer-dryers)—

• (i) in the third column of the entry relating to each of the following parameters, for “X,XX” substitute “X.XXX”—

• (aa) “Washing efficiency index of the eco 40-60 programme at rated washing capacity (IW)”;

• (bb) “Washing efficiency index of the eco 40-60 programme at half rated washing capacity (IW)”;

• (cc) “Washing efficiency index of the eco 40-60 programme at quarter rated washing capacity (IW)”;

• (dd) “Washing efficiency index of the wash and dry cycle at rated capacity (JW)”;

• (ee) “Washing efficiency index of the wash and dry cycle at half rated capacity (JW)”;

• (ii) omit the entry relating to each of the following parameters—

• (aa) “Remaining moisture content for the eco 40-60 programme at rated capacity (Dfull)”;

• (bb) “Remaining moisture content for the eco 40-60 programme at half capacity (D1/2)”;

• (cc) “Remaining moisture content for the eco 40-60 programme at quarter capacity (D1/4)”;

• (iii) in the third column of the entry relating to “Weighted remaining moisture content”, for “X” substitute “X.X”;

• (aa) in the first column of the entry relating to each of the following parameters, at the end insert “if applicable”—

• (bb) “Power consumption in ‘off mode’ (Po)”;

• (cc) “Power consumption in ‘standby mode’ (Psm)”.

• (8) In Annex 8 (information required where distance selling through the internet), in point 1, for “Annex IV” substitute “Annex 3”.

• (9) In Annex 9 (verification procedure for market surveillance purposes)—

• (a) for the first (unnumbered) paragraph substitute—

The verification tolerances set out in this Annex relate only to the verification by the market surveillance authority of the declared values. The supplier of a product must not use the verification tolerances— (a) to establish the declared values; (b) to interpret the declared values; or (c) to communicate better performance. The values and classes published on the label or in the product information sheet must not be more favourable to the supplier than the declared values.

• (b) in point 2(a), for “values given in the technical documentation pursuant to Article 3(3) of Regulation (EU) 2017/1369 (declared values),” substitute “declared values”;

• (c) in the final paragraph before Table 9, for “points 1 to 7” substitute “points 1 to 6”;

• (d) in Table 9—

• (i) in the second column of the entry relating to “Weighted energy consumption”, for “, respectively EWD,” substitute “and EWD respectively”;

• (ii) in the second column of the entry relating to “Weighted water consumption”, for “, respectively WWD,” substitute “and WWD respectively”;

• (iii) in the entry relating to “Washing efficiency index”—

• (aa) in the first column, after “(IW and JW)” insert “at all relevant loads”;

• (bb) in the second column, for “, respectively JW,” substitute “and JW respectively”;

• (iv) in the entry relating to “Rinsing effectiveness”—

• (aa) in the first column, after “(IR and JR)” insert “at all relevant loads”;

• (bb) in the second column, for “, respectively JR,” substitute “and JR respectively”;

• (v) in the first column of the entry relating to “programme or cycle duration”, after “programme or cycle duration” insert “(tw and twd) at all relevant loads”;

• (vi) in the first column of the entry relating to “Maximum temperature inside the laundry”, after “(T)” insert “during the washing cycle at all relevant loads”;

• (vii) omit the entry relating to “Dfull, D1/2, D1/4”;

• (viii) in the first column of the entry relating to “Remaining moisture content after washing”, at the beginning insert “Weighted”;

• (ix) in the first column of the entry relating to “Final moisture content after drying”, after “after drying” insert “at all relevant loads”;

• (x) in the first column of the entry relating to “Spin speed”, after “(S)” insert “at all relevant loads”.

• (10) In Annex 10 (multi-drum household washing machines and washer-dryers), in point (f), for “residual” substitute “remaining”.

Amendments to Commission Delegated Regulation (EU) 2019/2016: refrigerating appliances

6

• (1) Commission Delegated Regulation (EU) 2019/2016 is amended as follows.

• (2) In Article 2 (definitions), in point (31) (definition of ‘mobile refrigerating appliance’), for “electric mains operated” substitute “connected to the mains through an AC/DC converter purchased separately”.

• (3) In Article 3(1) (obligation of suppliers), for point (b) substitute—

(b) the information set out in Table 6 of Annex 5 (product information sheet) is made available on a publicly accessible website;

• (4) In Annex 1 (definitions), after point (41) insert—

(42) ‘declared values’ means the values provided by the supplier in the technical documentation in accordance with point 1(d) of Annex 6 for the verification of conformity by the market surveillance authority.

• (5) In Annex 4 (measurement methods and calculations)—

• (a) after the first (unnumbered) paragraph, insert—

Where a calculation in this Annex uses a parameter listed in Table 7 of Annex 6 (technical documentation), the supplier must use the declared value for that parameter.

• (b) in point 1 (general conditions for testing)—

• (i) for point (h), substitute—

(h) the freezing capacity of a compartment must be calculated at 24 times the light load weight of that compartment, divided by the freezing time to bring the temperature of the light load from +25 to -18 °C at an ambient temperature of 25 °C, expressed in kg/24 hr and rounded to one decimal place;

• (ii) for point (i), substitute—

(i) for 4-star compartments, the freezing time to bring the temperature of the light load from +25 to -18 °C at an ambient temperature of 25 °C must be such that the resulting freezing capacity complies with the requirement in point (4) of Annex 1 (definition of ‘freezing capacity’);

• (iii) after point (j) insert—

(k) the light load weight for a 4-star compartment must be calculated at 3.5 kg per 100 litres of the volume of the 4-star compartment, rounded up to the nearest 0.5 kg, except that it must be deemed to be 2 kg if that calculation results in a value lower than 2 kg; (l) if the refrigerating appliance includes a combination of 3-star and 4-star compartments, the sum of the light load weights must be calculated at 3.5 kg per 100 litres of the total volume of all 4-star and 3-star compartments, rounded up to the nearest 0.5 kg, except that it must be deemed to be 2 kg if that calculation results in a value lower than 2 kg.

• (6) In Annex 5 (product information sheet)—

• (a) in Table 6—

• (i) under the heading “General product parameters”, in the second column of the entry relating to “Annual energy consumption (kWHa)” for “x,xx” substitute “x”;

• (ii) under the heading “Compartment Parameters”, in the fifth column of the entry relating to each of the following parameters, for “x,xx” substitute “x.x”—

• (aa) “4-star”;

• (bb) “variable temperature compartment”;

• (iii) omit the row beginning “Light source parameters” and the two rows following it;

• (iv) after the entry relating to “Fast freeze facility” insert—

For wine storage appliance	For wine storage appliance
Number of standard 750 ml wine bottles	x
Light source parameters
Type of light source	[type]
Energy efficiency class	[A/B/C/D/E/F/G][^f00011]

• (v) omit footnotes “b” and “c” and the references to those footnotes;

• (b) after Table 6 insert—

(3) The following items in Table 6 are not relevant for the purposes of determining whether a model is an equivalent model under Article 2(6) of the Framework Regulation— (a) supplier’s name or trade mark; (b) supplier’s address; (c) model identifier; (d) overall dimensions (millimetre); (e) airborne acoustical noise emission class (dB(A) re 1 pW); (f) minimum duration of the guarantee given by the supplier; (g) additional information.

• (7) In Annex 6 (technical documentation), in point 1, for point (a) to the end substitute—

(a) a general description of the model, sufficient for it to be unequivocally and easily identified; (b) references to the designated standards applied or other measurement standards used; (c) specific precautions that must be taken when the model is assembled, installed, maintained or tested; (d) the values of the technical parameters set out in Table 7; (e) the details and the results of the calculations performed in accordance with Annex 4; (f) the testing conditions, if not fully described in the information provided under point (b); (g) the model identifier of all equivalent models already placed on the market.

A general description of the refrigerating model, sufficient for it to be unequivocally and easily identified:	A general description of the refrigerating model, sufficient for it to be unequivocally and easily identified:	A general description of the refrigerating model, sufficient for it to be unequivocally and easily identified:	A general description of the refrigerating model, sufficient for it to be unequivocally and easily identified:
Product specifications:
General product specifications:
Parameter	Value	Parameter	Value
Annual energy consumption (kWh/a)	x.xx	EEI %	x.x
Standard annual energy consumption (kWh/a)	x.xx	Combi parameter	x.xx
Temperature rise time (h)	x.xx	Load factor	x.x
Door heat loss factor	x.xxx	Climate class	[extended temperate/temperate/subtropical/tropical]
Anti-condensation heater type	[manual on-off/ambient/other/ none]	Airborne acoustical noise emissions (dB(A) re 1 pW)	x
Additional product specifications for refrigerating appliances, except for low noise refrigerating appliances:	Additional product specifications for refrigerating appliances, except for low noise refrigerating appliances:	Additional product specifications for refrigerating appliances, except for low noise refrigerating appliances:	Additional product specifications for refrigerating appliances, except for low noise refrigerating appliances:
Parameter	Value
Daily energy consumption at 32 °C (kWh/24h)	x.xxx
Additional product specifications for low noise refrigerating appliances	Additional product specifications for low noise refrigerating appliances	Additional product specifications for low noise refrigerating appliances	Additional product specifications for low noise refrigerating appliances
Parameter	Value
Daily energy consumption at 25 °C (kWh/24h)	x.xxx
Additional product specifications for wine storage appliances	Additional product specifications for wine storage appliances	Additional product specifications for wine storage appliances	Additional product specifications for wine storage appliances
Parameter	Value	Parameter	Value
Internal humidity (%)	[range]	Number of standard 750 ml bottles	x

If the refrigerating appliance contains more than one compartment of the same type, the lines for these compartments must be repeated. If a certain compartment type is absent, the values of the compartment parameters must be recorded as ‘-’.

Compartment specifications:	Compartment specifications:	Compartment specifications:	Compartment specifications:	Compartment specifications:	Compartment specifications:	Compartment specifications:	Compartment specifications:	Compartment specifications:	Compartment specifications:
		Compartment parameters and values	Compartment parameters and values	Compartment parameters and values	Compartment parameters and values	Compartment parameters and values	Compartment parameters and values	Compartment parameters and values	Compartment parameters and values
Compartment type	Compartment type	Target temperature (°C)	Compartment volume (dm³ or l)	Freezing capacity (kg/24 h)	Thermodynamic paramater (rc)	Nc	Mc	Defrost factor (Ac )	Built-in factor (Bc)
Pantry	Pantry	+17	x.x	-	0.35	75	0.12	1.00	x.xx
Wine storage	Wine storage	+12	x.x	-	0.60	75	0.12	1.00	x.xx
Cellar	Cellar	+12	x.x	-	0.60	75	0.12	1.00	x.xx
Fresh food	Fresh food	+4	x.x	-	1.00	75	0.12	1.00	x.xx
Chill	Chill	+2	x.x	-	1.10	138	0.12	x.xx	x.xx
0-star or ice making	0-star or ice making	0	x.x	-	1.20	138	0.15	x.xx	x.xx
1-star	1-star	-6	x.x	-	1.50	138	0.15	x.xx	x.xx
2-star	2-star	-12	x.x	-	1.80	138	0.15	x.xx	x.xx
3-star	3-star	-18	x.x	-	2.10	138	0.15	x.xx	x.xx
4-star	4-star	-18	x.x	x.x	2.10	138	0.15	x.xx	x.xx
2-star section	2-star section	-12	x.x	-	1.80	138	0.15	x.xx	x.xx
Variable temperature compartment	Variable temperature compartment	X	x.x	x.x (for 4-star compartments) or ‘-’	x.xx	x	x.xx	x.xx	x.xx
The sum of the volumes of the chill compartment(s) and the unfrozen compartment(s) (dm³ or l)	The sum of the volumes of the chill compartment(s) and the unfrozen compartment(s) (dm³ or l)		x
The sum of the volumes of the frozen compartment(s) (dm³ or l)	The sum of the volumes of the frozen compartment(s) (dm³ or l)		x

• (8) In Annex 9 (verification procedure for market surveillance purposes)—

• (a) for the first (unnumbered) paragraph substitute—

The verification tolerances set out in this Annex relate only to the verification by the market surveillance authority of the declared values. The supplier of a product must not use the verification tolerances— (a) to establish the declared values; (b) to interpret the declared values; or (c) to communicate better performance. The values and classes published on the label or in the product information sheet must not be more favourable to the supplier than the declared values.

• (b) in point (2)(a), for “values given in the technical documentation pursuant to Article 3(3) of Regulation (EU) 2017/1369 (declared values),” substitute “declared values”;

• (c) in the final paragraph before Table 8, for “points 1 to 7” substitute “points 1 to 6”;

• (d) in Table 8—

• (i) in the first column, for “E₁₆E₃₂” substitute “E₃₂”;

• (ii) omit the entry relating to “Eaux”;

• (iii) in the second column of the entry relating to “temperate rise time”, for “higher” substitute “lower”.

Amendments to Commission Delegated Regulation (EU) 2019/2017: household dishwashers

7

• (1) Commission Delegated Regulation (EU) 2019/2017 of 11 March 2019 supplementing Regulation (EU) 2017/1369 of the European Parliament and of the Council with regard to energy labelling of household dishwashers and repealing Commission Delegated Regulation (EU) No 1059/2010[^f00012], as modified by the Ecodesign for Energy-Related Products and Energy Information (Amendment) (EU Exit) Regulations 2020, is amended as follows.

• (2) In Article 3(1) (obligations of suppliers), for point (b) substitute—

(b) the information set out in Table 3 of Annex 5 is made available on a publicly accessible website;

• (3) In Annex 1 (definitions applicable for Annexes), after point (23) insert—

(24) ‘declared values’ means the values provided by the supplier in the technical documentation in accordance with point 1(d) of Annex 6 for the verification of conformity by the market surveillance authority.

• (4) In Annex 2, in point A (energy efficiency classes), in the heading of Table 1 for “electronic displays” substitute “household dishwashers”.

• (5) In Annex 4 (measurement methods and calculations)—

• (a) after the first paragraph insert—

Where a calculation in this Annex uses a parameter listed in Table 4 of Annex 6 (technical documentation), the supplier must use the declared value for that parameter.

• (b) in point 2 (cleaning performance index), in each place that it occurs, for “two decimal places” substitute “three decimal places”;

• (c) in point 3 (drying performance index), in each place that it occurs, for “two decimal places” substitute “three decimal places”;

• (d) for point 4 (low power modes) substitute—

(4) Where applicable, the power consumption of the off mode (Po), standby mode (Psm) and delay start (Pds) must be measured. The measured values must be expressed in W and rounded to two decimal places. During measurements of the power consumption in low power modes, the following must be checked and recorded— (a) whether information is displayed; (b) whether any network connection is activated.

• (6) In Annex 5 (product information sheet)—

• (a) number the first paragraph as paragraph 1;

• (b) number the second paragraph as paragraph 2;

• (c) in Table 3—

• (i) in the second column of the entry relating to each of the following parameters, for “x,xx” substitute “x.xxx”—

• (aa) “Cleaning performance index”;

• (bb) “Drying performance index”;

• (ii) omit footnotes (b) and (c) and the references to them;

• (d) after Table 3 insert—

(3) The following items in Table 3 are not relevant for the purposes of determining whether a model is an equivalent model under Article 2(6) of the Framework Regulation— (a) supplier’s name or trade mark; (b) supplier’s address; (c) model identifier; (d) dimensions in cm; (e) minimum duration of the guarantee given by the supplier; (f) additional information.

• (7) In Annex 6 (technical documentation), in point (1)—

• (a) for points (a) and (b) substitute—

(a) a general description of the model, sufficient for it to be unequivocally and easily identified; (b) references to the designated standards applied or other measurement standards used; (c) specific precautions that must be taken when the model is assembled, installed, maintained or tested; (d) the values of the technical parameters set out in Table 4; (e) the details and the results of the calculations performed in accordance with Annex 4; (f) the testing conditions, if not fully described in point (b); (g) the model identifier of all equivalent models already placed on the market;

• (b) in Table 4—

• (i) before the entry relating to “Eco programme energy consumption” insert—

Rated capacity in place settings	-	X

• (ii) in the first column of the entry relating to each of the following parameters, at the end insert “if applicable”—

• (aa) “Power consumption in ‘off mode’ (Po)”;

• (bb) “Power consumption in ‘standby mode’ (Psm)”;

• (iii) in the third column of the entry relating to each of the following parameters, for “X,XX” substitute “X.XXX”—

• (aa) “Cleaning performance index (IC)”;

• (bb) “Drying performance index (ID)”;

• (c) after Table 4, omit points (c) to (f).

• (8) In Annex 9—

• (a) for the first (unnumbered) paragraph substitute—

The verification tolerances set out in this Annex relate only to the verification by the market surveillance authority of the declared values. The supplier of a product must not use the verification tolerances— (a) to establish the declared values; (b) to interpret the declared values; or (c) to communicate better performance. The values and classes published on the label or in the product information sheet must not be more favourable to the supplier than the declared values.

• (b) in point (2)(a), for “values given in the technical documentation pursuant to Article 3(3) of Regulation (EU) 2017/1369 (declared values),” substitute “declared values”;

• (c) in the final paragraph before Table 5, for “points 1 to 7” substitute “points 1 to 6”.

PART 4 — AMENDMENTS TO THE ECODESIGN FOR ENERGY-RELATED PRODUCTS REGULATIONS 2010

Amendments to the Ecodesign for Energy-Related Products Regulations 2010

8

• (1) Schedule 1 to the Ecodesign for Energy-Related Products Regulations 2010[^f00013] (declaration of conformity) is amended as follows.

• (2) In the table at paragraph 4—

• (a) omit the entry relating to item 10 (a boiler or an appliance)[^f00014];

• (b) in relation to the products listed in the following table, for the existing text in the final column substitute the text in the final column of the following table—