LegalizeCommission Implementing Regulation (EU) No 927/2012 of 9 October 2012 amending Annex I to Council Regulation (EEC) No 2658/87 on the tariff and statistical nomenclature and on the Common Customs Tariff
This is the act as published. Later amendments are not folded into the text below: each one is a separate act in this repository and an entry in this law's history.
Alloys of copper and nickel, with or without other elements but in any case containing by weight not more than 1 % of zinc. When other elements are present, nickel predominates by weight over each of such other elements.
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 7401 00 00 | Copper mattes; cement copper (precipitated copper) | Free | — |
| 7402 00 00 | Unrefined copper; copper anodes for electrolytic refining | Free | — |
| 7403 | Refined copper and copper alloys, unwrought | ||
| – Refined copper | |||
| 7403 11 00 | – – Cathodes and sections of cathodes | Free | — |
| 7403 12 00 | – – Wire-bars | Free | — |
| 7403 13 00 | – – Billets | Free | — |
| 7403 19 00 | – – Other | Free | — |
| – Copper alloys | |||
| 7403 21 00 | – – Copper-zinc base alloys (brass) | Free | — |
| 7403 22 00 | – – Copper-tin base alloys (bronze) | Free | — |
| 7403 29 00 | – – Other copper alloys (other than master alloys of heading 7405 ) | Free | — |
| 7404 00 | Copper waste and scrap | ||
| 7404 00 10 | – Of refined copper | Free | — |
| – Of copper alloys | |||
| 7404 00 91 | – – Of copper-zinc base alloys (brass) | Free | — |
| 7404 00 99 | – – Other | Free | — |
| 7405 00 00 | Master alloys of copper | Free | — |
| 7406 | Copper powders and flakes | ||
| 7406 10 00 | – Powders of non-lamellar structure | Free | — |
| 7406 20 00 | – Powders of lamellar structure; flakes | Free | — |
| 7407 | Copper bars, rods and profiles | ||
| 7407 10 00 | – Of refined copper | 4,8 | — |
| – Of copper alloys | |||
| 7407 21 | – – Of copper-zinc base alloys (brass) | ||
| 7407 21 10 | – – – Bars and rods | 4,8 | — |
| 7407 21 90 | – – – Profiles | 4,8 | — |
| 7407 29 00 | – – Other | 4,8 | — |
| 7408 | Copper wire | ||
| – Of refined copper | |||
| 7408 11 00 | – – Of which the maximum cross-sectional dimension exceeds 6 mm | 4,8 | — |
| 7408 19 | – – Other | ||
| 7408 19 10 | – – – Of which the maximum cross-sectional dimension exceeds 0,5 mm | 4,8 | — |
| 7408 19 90 | – – – Of which the maximum cross-sectional dimension does not exceed 0,5 mm | 4,8 | — |
| – Of copper alloys | |||
| 7408 21 00 | – – Of copper-zinc base alloys (brass) | 4,8 | — |
| 7408 22 00 | – – Of copper-nickel base alloys (cupro-nickel) or copper-nickel-zinc base alloys (nickel silver) | 4,8 | — |
| 7408 29 00 | – – Other | 4,8 | — |
| 7409 | Copper plates, sheets and strip, of a thickness exceeding 0,15 mm | ||
| – Of refined copper | |||
| 7409 11 00 | – – In coils | 4,8 | — |
| 7409 19 00 | – – Other | 4,8 | — |
| – Of copper-zinc base alloys (brass) | |||
| 7409 21 00 | – – In coils | 4,8 | — |
| 7409 29 00 | – – Other | 4,8 | — |
| – Of copper-tin base alloys (bronze) | |||
| 7409 31 00 | – – In coils | 4,8 | — |
| 7409 39 00 | – – Other | 4,8 | — |
| 7409 40 00 | – Of copper-nickel base alloys (cupro-nickel) or copper-nickel-zinc base alloys (nickel silver) | 4,8 | — |
| 7409 90 00 | – Of other copper alloys | 4,8 | — |
| 7410 | Copper foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,15 mm | ||
| – Not backed | |||
| 7410 11 00 | – – Of refined copper | 5,2 | — |
| 7410 12 00 | – – Of copper alloys | 5,2 | — |
| – Backed | |||
| 7410 21 00 | – – Of refined copper | 5,2 | — |
| 7410 22 00 | – – Of copper alloys | 5,2 | — |
| 7411 | Copper tubes and pipes | ||
| 7411 10 | – Of refined copper | ||
| 7411 10 10 | – – Straight | 4,8 | — |
| 7411 10 90 | – – Other | 4,8 | — |
| – Of copper alloys | |||
| 7411 21 | – – Of copper-zinc base alloys (brass) | ||
| 7411 21 10 | – – – Straight | 4,8 | — |
| 7411 21 90 | – – – Other | 4,8 | — |
| 7411 22 00 | – – Of copper-nickel base alloys (cupro-nickel) or copper-nickel-zinc base alloys (nickel silver) | 4,8 | — |
| 7411 29 00 | – – Other | 4,8 | — |
| 7412 | Copper tube or pipe fittings (for example, couplings, elbows, sleeves) | ||
| 7412 10 00 | – Of refined copper | 5,2 | — |
| 7412 20 00 | – Of copper alloys | 5,2 | — |
| 7413 00 00 | Stranded wire, cables, plaited bands and the like, of copper, not electrically insulated | 5,2 | — |
| 7414 | |||
| 7415 | Nails, tacks, drawing pins, staples (other than those of heading 8305 ) and similar articles, of copper or of iron or steel with heads of copper; screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers (including spring washers) and similar articles, of copper | ||
| 7415 10 00 | – Nails and tacks, drawing pins, staples and similar articles | 4 | — |
| – Other articles, not threaded | |||
| 7415 21 00 | – – Washers (including spring washers) | 3 | — |
| 7415 29 00 | – – Other | 3 | — |
| – Other threaded articles | |||
| 7415 33 00 | – – Screws; bolts and nuts | 3 | — |
| 7415 39 00 | – – Other | 3 | — |
| 7416 | |||
| 7417 | |||
| 7418 | Table, kitchen or other household articles and parts thereof, of copper; pot scourers and scouring or polishing pads, gloves and the like, of copper; sanitary ware and parts thereof, of copper | ||
| 7418 10 | – Table, kitchen or other household articles and parts thereof; pot scourers and scouring or polishing pads, gloves and the like | ||
| 7418 10 10 | – – Cooking or heating apparatus of a kind used for domestic purposes, non-electric, and parts thereof | 4 | — |
| 7418 10 90 | – – Other | 3 | — |
| 7418 20 00 | – Sanitary ware and parts thereof | 3 | — |
| 7419 | Other articles of copper | ||
| 7419 10 00 | – Chain and parts thereof | 3 | — |
| – Other | |||
| 7419 91 00 | – – Cast, moulded, stamped or forged, but not further worked | 3 | — |
| 7419 99 | – – Other | ||
| 7419 99 10 | – – – Cloth (including endless bands), grill and netting, of wire of which no cross-sectional dimension exceeds 6 mm; expanded metal | 4,3 | — |
| 7419 99 30 | – – – Springs | 4 | — |
| 7419 99 90 | – – – Other | 3 | — |
CHAPTER 75
NICKEL AND ARTICLES THEREOF
Note
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Bars and rods:
Rolled, extruded, drawn or forged products, not in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width. The expression also covers cast or sintered products, of the same forms and dimensions, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (b) Profiles:
Rolled, extruded, drawn, forged or formed products, coiled or not, of a uniform cross-section along their whole length, which do not conform to any of the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes or pipes. The expression also covers cast or sintered products, of the same forms, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (c) Wire:
Rolled, extruded or drawn products, in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width.
- (d) Plates, sheets, strip and foil:
Flat-surfaced products (other than the unwrought products of heading 7502 ), coiled or not, of solid rectangular (other than square) cross-section with or without rounded corners (including ‘modified rectangles’ of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel) of a uniform thickness, which are:
- — of rectangular (including square) shape with a thickness not exceeding one-tenth of the width,
- — of a shape other than rectangular or square, of any size, provided that they do not assume the character of articles or products of other headings.
Heading 7506 applies, inter alia, to plates, sheets, strip and foil with patterns (for example, grooves, ribs, chequers, tears, buttons, lozenges) and to such products which have been perforated, corrugated, polished or coated, provided that they do not thereby assume the character of articles or products of other headings.
- (e) Tubes and pipes:
Hollow products, coiled or not, which have a uniform cross-section with only one enclosed void along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons, and which have a uniform wall thickness. Products with a rectangular (including square), equilateral triangular, or regular convex polygonal cross-section, which may have corners rounded along their whole length, are also to be considered as tubes and pipes provided the inner and outer cross-sections are concentric and have the same form and orientation. Tubes and pipes of the foregoing cross-sections may be polished, coated, bent, threaded, drilled, waisted, expanded, cone-shaped or fitted with flanges, collars or rings.
Subheading notes
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Nickel, not alloyed:
Metal containing by weight at least 99 % of nickel plus cobalt, provided that:
- (1) the cobalt content by weight does not exceed 1,5 %, and
- (2) the content by weight of any other element does not exceed the limit specified in the following table:
Other elements
| Element | Element | Limiting content % by weight |
|---|---|---|
| Fe | Iron | 0,5 |
| O | Oxygen | 0,4 |
| Other elements, each | Other elements, each | 0,3 |
- (b) Nickel alloys:
Metallic substances in which nickel predominates by weight over each of the other elements provided that:
- (1) the content by weight of cobalt exceeds 1,5 %,
- (2) the content by weight of at least one of the other elements is greater than the limit specified in the foregoing table, or
- (3) the total content by weight of elements other than nickel plus cobalt exceeds 1 %.
-
- Notwithstanding the provisions of chapter note 1(c), for the purposes of subheading 7508 10 the term ‘wire’ applies only to products, whether or not in coils, of any cross-sectional shape, of which no cross-sectional dimension exceeds 6 mm.
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 7501 | Nickel mattes, nickel oxide sinters and other intermediate products of nickel metallurgy | ||
| 7501 10 00 | – Nickel mattes | Free | — |
| 7501 20 00 | – Nickel oxide sinters and other intermediate products of nickel metallurgy | Free | — |
| 7502 | Unwrought nickel | ||
| 7502 10 00 | – Nickel, not alloyed | Free | — |
| 7502 20 00 | – Nickel alloys | Free | — |
| 7503 00 | Nickel waste and scrap | ||
| 7503 00 10 | – Of nickel, not alloyed | Free | — |
| 7503 00 90 | – Of nickel alloys | Free | — |
| 7504 00 00 | Nickel powders and flakes | Free | — |
| 7505 | Nickel bars, rods, profiles and wire | ||
| – Bars, rods and profiles | |||
| 7505 11 00 | – – Of nickel, not alloyed | Free | — |
| 7505 12 00 | – – Of nickel alloys | 2,9 | — |
| – Wire | |||
| 7505 21 00 | – – Of nickel, not alloyed | Free | — |
| 7505 22 00 | – – Of nickel alloys | 2,9 | — |
| 7506 | Nickel plates, sheets, strip and foil | ||
| 7506 10 00 | – Of nickel, not alloyed | Free | — |
| 7506 20 00 | – Of nickel alloys | 3,3 | — |
| 7507 | Nickel tubes, pipes and tube or pipe fittings (for example, couplings, elbows, sleeves) | ||
| – Tubes and pipes | |||
| 7507 11 00 | – – Of nickel, not alloyed | Free | — |
| 7507 12 00 | – – Of nickel alloys | Free | — |
| 7507 20 00 | – Tube or pipe fittings | 2,5 | — |
| 7508 | Other articles of nickel | ||
| 7508 10 00 | – Cloth, grill and netting, of nickel wire | Free | — |
| 7508 90 00 | – Other | Free | — |
CHAPTER 76
ALUMINIUM AND ARTICLES THEREOF
Note
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Bars and rods:
Rolled, extruded, drawn or forged products, not in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width. The expression also covers cast or sintered products, of the same forms and dimensions, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (b) Profiles:
Rolled, extruded, drawn, forged or formed products, coiled or not, of a uniform cross-section along their whole length, which do not conform to any of the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes or pipes. The expression also covers cast or sintered products, of the same forms, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (c) Wire:
Rolled, extruded or drawn products, in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width.
- (d) Plates, sheets, strip and foil:
Flat-surfaced products (other than the unwrought products of heading 7601 ), coiled or not, of solid rectangular (other than square) cross-section with or without rounded corners (including ‘modified rectangles’ of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel) of a uniform thickness, which are:
- — of rectangular (including square) shape with a thickness not exceeding one-tenth of the width,
- — of a shape other than rectangular or square, of any size, provided that they do not assume the character of articles or products of other headings.
Headings 7606 and 7607 apply, inter alia, to plates, sheets, strip and foil with patterns (for example, grooves, ribs, chequers, tears, buttons, lozenges) and to such products which have been perforated, corrugated, polished or coated, provided that they do not thereby assume the character of articles or products of other headings.
- (e) Tubes and pipes:
Hollow products, coiled or not, which have a uniform cross-section with only one enclosed void along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons, and which have a uniform wall thickness. Products with a rectangular (including square), equilateral triangular or regular convex polygonal cross-section, which may have corners rounded along their whole length, are also to be considered as tubes and pipes provided the inner and outer cross-sections are concentric and have the same form and orientation. Tubes and pipes of the foregoing cross-sections may be polished, coated, bent, threaded, drilled, waisted, expanded, cone-shaped or fitted with flanges, collars or rings.
Subheading notes
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Aluminium, not alloyed:
Metal containing by weight at least 99 % of aluminium, provided that the content by weight of any other element does not exceed the limit specified in the following table:
Other elements
| Element | Limiting content % by weight |
|---|---|
| Fe + Si (iron plus silicon) | 1 |
| Other elements88, each | 0,189 |
- (b) Aluminium alloys:
Metallic substances in which aluminium predominates by weight over each of the other elements, provided that:
- (1) the content by weight of at least one of the other elements or of iron plus silicon taken together is greater than the limit specified in the foregoing table; or
- (2) the total content by weight of such other elements exceeds 1 %.
-
- Notwithstanding the provisions of chapter note 1(c), for the purposes of subheading 7616 91 the term ‘wire’ applies only to products, whether or not in coils, of any cross-sectional shape, of which no cross-sectional dimension exceeds 6 mm.
Additional note
-
- For the purposes of subheading 7601 20 20 , the following terms shall have the meanings hereby assigned to them:
- — ‘slabs’: unwrought products which have a uniform solid cross-section along their whole length in the shape of a rectangle or other polygon, of a width exceeding 800 mm, of a thickness exceeding 280 mm and of a length always superior to the width and to the thickness. These products are intended for being rolled,
- — ‘billets’: unwrought products which have a uniform solid cross-section along their whole length in the shape of a circle (including a ‘flattened circle’), of a diameter exceeding 125 mm. These products are intended for being extruded.
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 7601 | Unwrought aluminium | ||
| 7601 10 00 | – Aluminium, not alloyed | 6 80 | — |
| 7601 20 | – Aluminium alloys | ||
| 7601 20 20 | – – Slabs and billets | 6 | — |
| 7601 20 80 | – – Other | 6 | — |
| 7602 00 | Aluminium waste and scrap | ||
| – Waste | |||
| 7602 00 11 | – – Turnings, shavings, chips, milling waste, sawdust and filings; waste of coloured, coated or bonded sheets and foil, of a thickness (excluding any backing) not exceeding 0,2 mm | Free | — |
| 7602 00 19 | – – Other (including factory rejects) | Free | — |
| 7602 00 90 | – Scrap | Free | — |
| 7603 | Aluminium powders and flakes | ||
| 7603 10 00 | – Powders of non-lamellar structure | 5 | — |
| 7603 20 00 | – Powders of lamellar structure; flakes | 5 | — |
| 7604 | Aluminium bars, rods and profiles | ||
| 7604 10 | – Of aluminium, not alloyed | ||
| 7604 10 10 | – – Bars and rods | 7,5 | — |
| 7604 10 90 | – – Profiles | 7,5 | — |
| – Of aluminium alloys | |||
| 7604 21 00 | – – Hollow profiles | 7,5 | — |
| 7604 29 | – – Other | ||
| 7604 29 10 | – – – Bars and rods | 7,5 | — |
| 7604 29 90 | – – – Profiles | 7,5 | — |
| 7605 | Aluminium wire | ||
| – Of aluminium, not alloyed | |||
| 7605 11 00 | – – Of which the maximum cross-sectional dimension exceeds 7 mm | 7,5 | — |
| 7605 19 00 | – – Other | 7,5 | — |
| – Of aluminium alloys | |||
| 7605 21 00 | – – Of which the maximum cross-sectional dimension exceeds 7 mm | 7,5 | — |
| 7605 29 00 | – – Other | 7,5 | — |
| 7606 | Aluminium plates, sheets and strip, of a thickness exceeding 0,2 mm | ||
| – Rectangular (including square) | |||
| 7606 11 | – – Of aluminium, not alloyed | ||
| 7606 11 10 | – – – Painted, varnished or coated with plastics | 7,5 | — |
| – – – Other, of a thickness of | |||
| 7606 11 91 | – – – – Less than 3 mm | 7,5 | — |
| 7606 11 93 | – – – – Not less than 3 mm but less than 6 mm | 7,5 | — |
| 7606 11 99 | – – – – Not less than 6 mm | 7,5 | — |
| 7606 12 | – – Of aluminium alloys | ||
| 7606 12 20 | – – – Painted, varnished or coated with plastics | 7,5 | — |
| – – – Other, of a thickness of | |||
| 7606 12 92 | – – – – Less than 3 mm | 7,5 | — |
| 7606 12 93 | – – – – Not less than 3 mm but less than 6 mm | 7,5 | — |
| 7606 12 99 | – – – – Not less than 6 mm | 7,5 | — |
| – Other | |||
| 7606 91 00 | – – Of aluminium, not alloyed | 7,5 | — |
| 7606 92 00 | – – Of aluminium alloys | 7,5 | — |
| 7607 | Aluminium foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials) of a thickness (excluding any backing) not exceeding 0,2 mm | ||
| – Not backed | |||
| 7607 11 | – – Rolled but not further worked | ||
| – – – Of a thickness of less than 0,021 mm | |||
| 7607 11 11 | – – – – In rolls of a weight not exceeding 10 kg | 7,5 | — |
| 7607 11 19 | – – – – Other | 7,5 | — |
| 7607 11 90 | – – – Of a thickness of not less than 0,021 mm but not more than 0,2 mm | 7,5 | — |
| 7607 19 | – – Other | ||
| 7607 19 10 | – – – Of a thickness of less than 0,021 mm | 7,5 | — |
| 7607 19 90 | – – – Of a thickness of not less than 0,021 mm but not more than 0,2 mm | 7,5 | — |
| 7607 20 | – Backed | ||
| 7607 20 10 | – – Of a thickness (excluding any backing) of less than 0,021 mm | 10 | — |
| 7607 20 90 | – – Of a thickness (excluding any backing) of not less than 0,021 mm but not more than 0,2 mm | 7,5 | — |
| 7608 | Aluminium tubes and pipes | ||
| 7608 10 00 | – Of aluminium, not alloyed | 7,5 | — |
| 7608 20 | – Of aluminium alloys | ||
| 7608 20 20 | – – Welded | 7,5 | — |
| – – Other | |||
| 7608 20 81 | – – – Not further worked than extruded | 7,5 | — |
| 7608 20 89 | – – – Other | 7,5 | — |
| 7609 00 00 | Aluminium tube or pipe fittings (for example, couplings, elbows, sleeves) | 5,9 | — |
| 7610 | Aluminium structures (excluding prefabricated buildings of heading 9406 ) and parts of structures (for example, bridges and bridge-sections, towers, lattice masts, roofs, roofing frameworks, doors and windows and their frames and thresholds for doors, balustrades, pillars and columns); aluminium plates, rods, profiles, tubes and the like, prepared for use in structures | ||
| 7610 10 00 | – Doors, windows and their frames and thresholds for doors | 6 | p/st 75 |
| 7610 90 | – Other | ||
| 7610 90 10 | – – Bridges and bridge-sections, towers and lattice masts | 7 | — |
| 7610 90 90 | – – Other | 6 | — |
| 7611 00 00 | Aluminium reservoirs, tanks, vats and similar containers, for any material (other than compressed or liquefied gas), of a capacity exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment | 6 | — |
| 7612 | Aluminium casks, drums, cans, boxes and similar containers (including rigid or collapsible tubular containers), for any material (other than compressed or liquefied gas), of a capacity not exceeding 300 litres, whether or not lined or heat-insulated, but not fitted with mechanical or thermal equipment | ||
| 7612 10 00 | – Collapsible tubular containers | 6 | — |
| 7612 90 | – Other | ||
| 7612 90 20 | – – Containers of a kind used for aerosols | 6 | p/st |
| 7612 90 90 | – – Other | 6 | — |
| 7613 00 00 | Aluminium containers for compressed or liquefied gas | 6 | — |
| 7614 | Stranded wire, cables, plaited bands and the like, of aluminium, not electrically insulated | ||
| 7614 10 00 | – With steel core | 6 | — |
| 7614 90 00 | – Other | 6 | — |
| 7615 | Table, kitchen or other household articles and parts thereof, of aluminium; pot scourers and scouring or polishing pads, gloves and the like, of aluminium; sanitary ware and parts thereof, of aluminium | ||
| 7615 10 | – Table, kitchen or other household articles and parts thereof; pot scourers and scouring or polishing pads, gloves and the like | ||
| 7615 10 10 | – – Cast | 6 | — |
| 7615 10 90 | – – Other | 6 | — |
| 7615 20 00 | – Sanitary ware and parts thereof | 6 | — |
| 7616 | Other articles of aluminium | ||
| 7616 10 00 | – Nails, tacks, staples (other than those of heading 8305 ), screws, bolts, nuts, screw hooks, rivets, cotters, cotter pins, washers and similar articles | 6 | — |
| – Other | |||
| 7616 91 00 | – – Cloth, grill, netting and fencing, of aluminium wire | 6 | — |
| 7616 99 | – – Other | ||
| 7616 99 10 | – – – Cast | 6 | — |
| 7616 99 90 | – – – Other | 6 | — |
CHAPTER 78
LEAD AND ARTICLES THEREOF
Note
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Bars and rods:
Rolled, extruded, drawn or forged products, not in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width. The expression also covers cast or sintered products, of the same forms and dimensions, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (b) Profiles:
Rolled, extruded, drawn, forged or formed products, coiled or not, of a uniform cross-section along their whole length, which do not conform to any of the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes or pipes. The expression also covers cast or sintered products, of the same forms, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (c) Wire:
Rolled, extruded or drawn products, in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width.
- (d) Plates, sheets, strip and foil:
Flat-surfaced products (other than the unwrought products of heading 7801 ), coiled or not, of solid rectangular (other than square) cross-section with or without rounded corners (including ‘modified rectangles’ of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel) of a uniform thickness, which are:
- — of rectangular (including square) shape with a thickness not exceeding one-tenth of the width,
- — of a shape other than rectangular or square, of any size, provided that they do not assume the character of articles or products of other headings.
Heading 7804 applies, inter alia, to plates, sheets, strip and foil with patterns (for example, grooves, ribs, chequers, tears, buttons, lozenges) and to such products which have been perforated, corrugated, polished or coated, provided that they do not thereby assume the character of articles or products of other headings.
- (e) Tubes and pipes:
Hollow products, coiled or not, which have a uniform cross-section with only one enclosed void along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons, and which have a uniform wall thickness. Products with a rectangular (including square), equilateral triangular or regular convex polygonal cross-section, which may have corners rounded along their whole length, are also to be considered as tubes and pipes provided the inner and outer cross-sections are concentric and have the same form and orientation. Tubes and pipes of the foregoing cross-sections may be polished, coated, bent, threaded, drilled, waisted, expanded, cone-shaped or fitted with flanges, collars or rings.
Subheading note
-
- In this chapter, the expression ‘refined lead’ means:
Metal containing by weight at least 99,9 % of lead, provided that the content by weight of any other element does not exceed the limit specified in the following table:
Other elements
| Element | Element | Limiting content % by weight |
|---|---|---|
| Ag | Silver | 0,02 |
| As | Arsenic | 0,005 |
| Bi | Bismuth | 0,05 |
| Ca | Calcium | 0,002 |
| Cd | Cadmium | 0,002 |
| Cu | Copper | 0,08 |
| Fe | Iron | 0,002 |
| S | Sulphur | 0,002 |
| Sb | Antimony | 0,005 |
| Sn | Tin | 0,005 |
| Zn | Zinc | 0,002 |
| Other (for example, Te), each | Other (for example, Te), each | 0,001 |
| --- | --- | --- |
| CN code | Description | Conventional rate of duty (%) |
| (1) | (2) | (3) |
| 7801 | Unwrought lead | |
| 7801 10 00 | – Refined lead | 2,5 |
| – Other | ||
| 7801 91 00 | – – Containing by weight antimony as the principal other element | 2,5 90 |
| 7801 99 | – – Other | |
| 7801 99 10 | – – – For refining, containing 0,02 % or more by weight of silver (bullion lead) 13 | Free |
| 7801 99 90 | – – – Other | 2,5 |
| 7802 00 00 | Lead waste and scrap | Free |
| 7803 | ||
| 7804 | Lead plates, sheets, strip and foil; lead powders and flakes | |
| – Plates, sheets, strip and foil | ||
| 7804 11 00 | – – Sheets, strip and foil of a thickness (excluding any backing) not exceeding 0,2 mm | 5 |
| 7804 19 00 | – – Other | 5 |
| 7804 20 00 | – Powders and flakes | Free |
| 7805 | ||
| 7806 00 | Other articles of lead | |
| 7806 00 10 | – Containers with an anti-radiation lead covering, for the transport or storage of radioactive materials (Euratom) | Free |
| 7806 00 80 | – Other | 5 |
CHAPTER 79
ZINC AND ARTICLES THEREOF
Note
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Bars and rods:
Rolled, extruded, drawn or forged products, not in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width. The expression also covers cast or sintered products, of the same forms and dimensions, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (b) Profiles:
Rolled, extruded, drawn, forged or formed products, coiled or not, of a uniform cross-section along their whole length, which do not conform to any of the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes or pipes. The expression also covers cast or sintered products, of the same forms, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (c) Wire:
Rolled, extruded or drawn products, in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width.
- (d) Plates, sheets, strip and foil:
Flat-surfaced products (other than the unwrought products of heading 7901 ), coiled or not, of solid rectangular (other than square) cross-section with or without rounded corners (including ‘modified rectangles’ of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel) of a uniform thickness, which are:
- — of rectangular (including square) shape with a thickness not exceeding one-tenth of the width,
- — of a shape other than rectangular or square, of any size, provided that they do not assume the character of articles or products of other headings.
Heading 7905 applies, inter alia, to plates, sheets, strip and foil with patterns (for example, grooves, ribs, chequers, tears, buttons, lozenges) and to such products which have been perforated, corrugated, polished or coated, provided that they do not thereby assume the character of articles or products of other headings.
- (e) Tubes and pipes:
Hollow products, coiled or not, which have a uniform cross-section with only one enclosed void along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons, and which have a uniform wall thickness. Products with a rectangular (including square), equilateral triangular or regular convex polygonal cross-section, which may have corners rounded along their whole length, are also to be considered as tubes and pipes provided the inner and outer cross-sections are concentric and have the same form and orientation. Tubes and pipes of the foregoing cross-sections may be polished, coated, bent, threaded, drilled, waisted, expanded, cone-shaped or fitted with flanges, collars or rings.
Subheading note
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Zinc, not alloyed:
Metal containing by weight at least 97,5 % of zinc.
- (b) Zinc alloys:
Metallic substances in which zinc predominates by weight over each of the other elements, provided that the total content by weight of such other elements exceeds 2,5 %.
- (c) Zinc dust:
Dust obtained by condensation of zinc vapour, consisting of spherical particles which are finer than zinc powders. At least 80 % by weight of the particles pass through a sieve with 63 μm (microns) mesh. It must contain at least 85 % by weight of metallic zinc.
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 7901 | Unwrought zinc | ||
| – Zinc, not alloyed | |||
| 7901 11 00 | – – Containing by weight 99,99 % or more of zinc | 2,5 | — |
| 7901 12 | – – Containing by weight less than 99,99 % of zinc | ||
| 7901 12 10 | – – – Containing by weight 99,95 % or more but less than 99,99 % of zinc | 2,5 | — |
| 7901 12 30 | – – – Containing by weight 98,5 % or more but less than 99,95 % of zinc | 2,5 | — |
| 7901 12 90 | – – – Containing by weight 97,5 % or more but less than 98,5 % of zinc | 2,5 | — |
| 7901 20 00 | – Zinc alloys | 2,5 | — |
| 7902 00 00 | Zinc waste and scrap | Free | — |
| 7903 | Zinc dust, powders and flakes | ||
| 7903 10 00 | – Zinc dust | 2,5 | — |
| 7903 90 00 | – Other | 2,5 | — |
| 7904 00 00 | Zinc bars, rods, profiles and wire | 5 | — |
| 7905 00 00 | Zinc plates, sheets, strip and foil | 5 | — |
| 7906 | |||
| 7907 00 00 | Other articles of zinc | 5 | — |
CHAPTER 80
TIN AND ARTICLES THEREOF
Note
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Bars and rods:
Rolled, extruded, drawn or forged products, not in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width. The expression also covers cast or sintered products, of the same forms and dimensions, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (b) Profiles:
Rolled, extruded, drawn, forged or formed products, coiled or not, of a uniform cross-section along their whole length, which do not conform to any of the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes or pipes. The expression also covers cast or sintered products, of the same forms, which have been subsequently worked after production (otherwise than by simple trimming or descaling), provided that they have not thereby assumed the character of articles or products of other headings.
- (c) Wire:
Rolled, extruded or drawn products, in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including ‘flattened circles’ and ‘modified rectangles’, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including ‘modified rectangular’) cross-section exceeds one-tenth of the width.
- (d) Plates, sheets, strip and foil:
Flat-surfaced products (other than the unwrought products of heading 8001 ), coiled or not, of solid rectangular (other than square) cross-section with or without rounded corners (including ‘modified rectangles’ of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel) of a uniform thickness, which are:
- — of rectangular (including square) shape with a thickness not exceeding one-tenth of the width,
- — of a shape other than rectangular or square, of any size, provided that they do not assume the character of articles or products of other headings.
- (e) Tubes and pipes:
Hollow products, coiled or not, which have a uniform cross-section with only one enclosed void along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons, and which have a uniform wall thickness. Products with a rectangular (including square), equilateral triangular or regular convex polygonal cross-section, which may have corners rounded along their whole length, are also to be considered as tubes and pipes provided the inner and outer cross-sections are concentric and have the same form and orientation. Tubes and pipes of the foregoing cross-sections may be polished, coated, bent, threaded, drilled, waisted, expanded, cone-shaped or fitted with flanges, collars or rings.
Subheading note
-
- In this chapter, the following expressions have the meanings hereby assigned to them:
- (a) Tin, not alloyed:
Metal containing by weight at least 99 % of tin, provided that the content by weight of any bismuth or copper is less than the limit specified in the following table:
Other elements
| Element | Element | Limiting content % by weight |
|---|---|---|
| Bi | Bismuth | 0,1 |
| Cu | Copper | 0,4 |
- (b) Tin alloys:
Metallic substances in which tin predominates by weight over each of the other elements, provided that:
- (1) the total content by weight of such other elements exceeds 1 %; or
- (2) the content by weight of either bismuth or copper is equal to or greater than the limit specified in the foregoing table.
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 8001 | Unwrought tin | ||
| 8001 10 00 | – Tin, not alloyed | Free | — |
| 8001 20 00 | – Tin alloys | Free | — |
| 8002 00 00 | Tin waste and scrap | Free | — |
| 8003 00 00 | Tin bars, rods, profiles and wire | Free | — |
| 8004 | |||
| 8005 | |||
| 8006 | |||
| 8007 00 | Other articles of tin | ||
| 8007 00 10 | – Plates, sheets and strip, of a thickness exceeding 0,2 mm | Free | — |
| 8007 00 80 | – Other | Free | — |
CHAPTER 81
OTHER BASE METALS; CERMETS; ARTICLES THEREOF
Subheading note
-
- Note 1 to Chapter 74, defining ‘bars and rods’, ‘profiles’, ‘wire’ and ‘plates, sheets, strip and foil’ applies, mutatis mutandis, to this chapter.
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 8101 | Tungsten (wolfram) and articles thereof, including waste and scrap | ||
| 8101 10 00 | – Powders | 5 | — |
| – Other | |||
| 8101 94 00 | – – Unwrought tungsten, including bars and rods obtained simply by sintering | 5 | — |
| 8101 96 00 | – – Wire | 6 | — |
| 8101 97 00 | – – Waste and scrap | Free | — |
| 8101 99 | – – Other | ||
| 8101 99 10 | – – – Bars and rods, other than those obtained simply by sintering, profiles, plates, sheets, strip and foil | 6 | — |
| 8101 99 90 | – – – Other | 7 | — |
| 8102 | Molybdenum and articles thereof, including waste and scrap | ||
| 8102 10 00 | – Powders | 4 | — |
| – Other | |||
| 8102 94 00 | – – Unwrought molybdenum, including bars and rods obtained simply by sintering | 3 | — |
| 8102 95 00 | – – Bars and rods, other than those obtained simply by sintering, profiles, plates, sheets, strip and foil | 5 | — |
| 8102 96 00 | – – Wire | 6,1 | — |
| 8102 97 00 | – – Waste and scrap | Free | — |
| 8102 99 00 | – – Other | 7 | — |
| 8103 | Tantalum and articles thereof, including waste and scrap | ||
| 8103 20 00 | – Unwrought tantalum, including bars and rods obtained simply by sintering; powders | Free | — |
| 8103 30 00 | – Waste and scrap | Free | — |
| 8103 90 | – Other | ||
| 8103 90 10 | – – Bars and rods, other than those obtained simply by sintering, profiles, wire, plates, sheets, strip and foil | 3 | — |
| 8103 90 90 | – – Other | 4 | — |
| 8104 | Magnesium and articles thereof, including waste and scrap | ||
| – Unwrought magnesium | |||
| 8104 11 00 | – – Containing at least 99,8 % by weight of magnesium | 5,3 | — |
| 8104 19 00 | – – Other | 4 | — |
| 8104 20 00 | – Waste and scrap | Free | — |
| 8104 30 00 | – Raspings, turnings and granules, graded according to size; powders | 4 | — |
| 8104 90 00 | – Other | 4 | — |
| 8105 | Cobalt mattes and other intermediate products of cobalt metallurgy; cobalt and articles thereof, including waste and scrap | ||
| 8105 20 00 | – Cobalt mattes and other intermediate products of cobalt metallurgy; unwrought cobalt; powders | Free | — |
| 8105 30 00 | – Waste and scrap | Free | — |
| 8105 90 00 | – Other | 3 | — |
| 8106 00 | Bismuth and articles thereof, including waste and scrap | ||
| 8106 00 10 | – Unwrought bismuth; waste and scrap; powders | Free | — |
| 8106 00 90 | – Other | 2 | — |
| 8107 | Cadmium and articles thereof, including waste and scrap | ||
| 8107 20 00 | – Unwrought cadmium; powders | 3 | — |
| 8107 30 00 | – Waste and scrap | Free | — |
| 8107 90 00 | – Other | 4 | — |
| 8108 | Titanium and articles thereof, including waste and scrap | ||
| 8108 20 00 | – Unwrought titanium; powders | 5 | — |
| 8108 30 00 | – Waste and scrap | 5 | — |
| 8108 90 | – Other | ||
| 8108 90 30 | – – Bars, rods, profiles and wire | 7 | — |
| 8108 90 50 | – – Plates, sheets, strip and foil | 7 | — |
| 8108 90 60 | – – Tubes and pipes | 7 | — |
| 8108 90 90 | – – Other | 7 | — |
| 8109 | Zirconium and articles thereof, including waste and scrap | ||
| 8109 20 00 | – Unwrought zirconium; powders | 5 | — |
| 8109 30 00 | – Waste and scrap | Free | — |
| 8109 90 00 | – Other | 9 | — |
| 8110 | Antimony and articles thereof, including waste and scrap | ||
| 8110 10 00 | – Unwrought antimony; powders | 7 | — |
| 8110 20 00 | – Waste and scrap | Free | — |
| 8110 90 00 | – Other | 7 | — |
| 8111 00 | Manganese and articles thereof, including waste and scrap | ||
| – Unwrought manganese; waste and scrap; powders | |||
| 8111 00 11 | – – Unwrought manganese; powders | Free | — |
| 8111 00 19 | – – Waste and scrap | Free | — |
| 8111 00 90 | – Other | 5 | — |
| 8112 | Beryllium, chromium, germanium, vanadium, gallium, hafnium, indium, niobium (columbium), rhenium and thallium, and articles of these metals, including waste and scrap | ||
| – Beryllium | |||
| 8112 12 00 | – – Unwrought; powders | Free | — |
| 8112 13 00 | – – Waste and scrap | Free | — |
| 8112 19 00 | – – Other | 3 | — |
| – Chromium | |||
| 8112 21 | – – Unwrought; powders | ||
| 8112 21 10 | – – – Alloys containing more than 10 % by weight of nickel | Free | — |
| 8112 21 90 | – – – Other | 3 | — |
| 8112 22 00 | – – Waste and scrap | Free | — |
| 8112 29 00 | – – Other | 5 | — |
| – Thallium | |||
| 8112 51 00 | – – Unwrought; powders | 1,5 | — |
| 8112 52 00 | – – Waste and scrap | Free | — |
| 8112 59 00 | – – Other | 3 | — |
| – Other | |||
| 8112 92 | – – Unwrought; waste and scrap; powders | ||
| 8112 92 10 | – – – Hafnium (celtium) | 3 | — |
| – – – Niobium (columbium); rhenium; gallium; indium; vanadium; germanium | |||
| 8112 92 21 | – – – – Waste and scrap | Free | — |
| – – – – Other | |||
| 8112 92 31 | – – – – – Niobium (columbium); rhenium | 3 | — |
| 8112 92 81 | – – – – – Indium | 2 | — |
| 8112 92 89 | – – – – – Gallium | 1,5 | — |
| 8112 92 91 | – – – – – Vanadium | Free | — |
| 8112 92 95 | – – – – – Germanium | 4,5 | — |
| 8112 99 | – – Other | ||
| 8112 99 20 | – – – Hafnium (celtium); germanium | 7 | — |
| 8112 99 30 | – – – Niobium (columbium); rhenium | 9 | — |
| 8112 99 70 | – – – Gallium; indium; vanadium | 3 | — |
| 8113 00 | Cermets and articles thereof, including waste and scrap | ||
| 8113 00 20 | – Unwrought | 4 | — |
| 8113 00 40 | – Waste and scrap | Free | — |
| 8113 00 90 | – Other | 5 | — |
CHAPTER 82
TOOLS, IMPLEMENTS, CUTLERY, SPOONS AND FORKS, OF BASE METAL; PARTS THEREOF OF BASE METAL
Notes
-
- Apart from blowlamps, portable forges, grinding wheels with frameworks, manicure and pedicure sets, and goods of heading 8209 , this chapter covers only articles with a blade, working edge, working surface or other working part of:
- (a) base metal;
- (b) metal carbides or cermets;
- (c) precious or semi-precious stones (natural, synthetic or reconstructed) on a support of base metal, metal carbide or cermet; or
- (d) abrasive materials on a support of base metal, provided that the articles have cutting teeth, flutes, grooves, or the like, of base metal, which retain their identity and function after the application of the abrasive.
-
- Parts of base metal of the articles of this chapter are to be classified with the articles of which they are parts, except parts separately specified as such and tool-holders for hand tools (heading 8466 ). However, parts of general use as defined in note 2 to Section XV are in all cases excluded from this chapter.
Heads, blades and cutting plates for electric shavers or electric hair clippers are to be classified in heading 8510 .
-
- Sets consisting of one or more knives of heading 8211 and at least an equal number of articles of heading 8215 are to be classified in heading 8215 .
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 8201 | Hand tools, the following: spades, shovels, mattocks, picks, hoes, forks and rakes; axes, billhooks and similar hewing tools; secateurs and pruners of any kind; scythes, sickles, hay knives, hedge shears, timber wedges and other tools of a kind used in agriculture, horticulture or forestry | ||
| 8201 10 00 | – Spades and shovels | 1,7 | p/st |
| 8201 30 00 | – Mattocks, picks, hoes and rakes | 1,7 | — |
| 8201 40 00 | – Axes, billhooks and similar hewing tools | 1,7 | — |
| 8201 50 00 | – Secateurs and similar one-handed pruners and shears (including poultry shears) | 1,7 | p/st |
| 8201 60 00 | – Hedge shears, two-handed pruning shears and similar two-handed shears | 1,7 | — |
| 8201 90 00 | – Other hand tools of a kind used in agriculture, horticulture or forestry | 1,7 | — |
| 8202 | Handsaws; blades for saws of all kinds (including slitting, slotting or toothless saw blades) | ||
| 8202 10 00 | – Handsaws | 1,7 | — |
| 8202 20 00 | – Bandsaw blades | 1,7 | — |
| – Circular saw blades (including slitting or slotting saw blades) | |||
| 8202 31 00 | – – With working part of steel | 2,7 | — |
| 8202 39 00 | – – Other, including parts | 2,7 | — |
| 8202 40 00 | – Chainsaw blades | 1,7 | — |
| – Other saw blades | |||
| 8202 91 00 | – – Straight saw blades, for working metal | 2,7 | — |
| 8202 99 | – – Other | ||
| 8202 99 20 | – – – For working metal | 2,7 | — |
| 8202 99 80 | – – – For working other materials | 2,7 | — |
| 8203 | Files, rasps, pliers (including cutting pliers), pincers, tweezers, metal-cutting shears, pipe-cutters, bolt croppers, perforating punches and similar hand tools | ||
| 8203 10 00 | – Files, rasps and similar tools | 1,7 | — |
| 8203 20 00 | – Pliers (including cutting pliers), pincers, tweezers and similar tools | 1,7 | — |
| 8203 30 00 | – Metal-cutting shears and similar tools | 1,7 | — |
| 8203 40 00 | – Pipe-cutters, bolt croppers, perforating punches and similar tools | 1,7 | — |
| 8204 | Hand-operated spanners and wrenches (including torque meter wrenches but not including tap wrenches); interchangeable spanner sockets, with or without handles | ||
| – Hand-operated spanners and wrenches | |||
| 8204 11 00 | – – Non-adjustable | 1,7 | — |
| 8204 12 00 | – – Adjustable | 1,7 | — |
| 8204 20 00 | – Interchangeable spanner sockets, with or without handles | 1,7 | — |
| 8205 | Hand tools (including glaziers' diamonds), not elsewhere specified or included; blowlamps; vices, clamps and the like, other than accessories for and parts of machine tools; anvils; portable forges; hand- or pedal-operated grinding wheels with frameworks | ||
| 8205 10 00 | – Drilling, threading or tapping tools | 1,7 | — |
| 8205 20 00 | – Hammers and sledge hammers | 3,7 | — |
| 8205 30 00 | – Planes, chisels, gouges and similar cutting tools for working wood | 3,7 | — |
| 8205 40 00 | – Screwdrivers | 3,7 | — |
| – Other hand tools (including glaziers' diamonds) | |||
| 8205 51 00 | – – Household tools | 3,7 | — |
| 8205 59 | – – Other | ||
| 8205 59 10 | – – – Tools for masons, moulders, cement workers, plasterers and painters | 3,7 | — |
| 8205 59 80 | – – – Other | 2,7 | — |
| 8205 60 00 | – Blowlamps | 2,7 | — |
| 8205 70 00 | – Vices, clamps and the like | 3,7 | — |
| 8205 90 | – Other, including sets of articles of two or more subheadings of this heading | ||
| 8205 90 10 | – – Anvils; portable forges; hand- or pedal-operated grinding wheels with frameworks | 2,7 | — |
| 8205 90 90 | – – Sets of articles of two or more subheadings of this heading | 3,7 | — |
| 8206 00 00 | Tools of two or more of headings 8202 to 8205 , put up in sets for retail sale | 3,7 | — |
| 8207 | Interchangeable tools for hand tools, whether or not power-operated, or for machine tools (for example, for pressing, stamping, punching, tapping, threading, drilling, boring, broaching, milling, turning or screw driving), including dies for drawing or extruding metal, and rock-drilling or earth-boring tools | ||
| – Rock-drilling or earth-boring tools | |||
| 8207 13 00 | – – With working part of cermets | 2,7 | — |
| 8207 19 | – – Other, including parts | ||
| 8207 19 10 | – – – With working part of diamond or agglomerated diamond | 2,7 | — |
| 8207 19 90 | – – – Other | 2,7 | — |
| 8207 20 | – Dies for drawing or extruding metal | ||
| 8207 20 10 | – – With working part of diamond or agglomerated diamond | 2,7 | — |
| 8207 20 90 | – – With working part of other materials | 2,7 | — |
| 8207 30 | – Tools for pressing, stamping or punching | ||
| 8207 30 10 | – – For working metal | 2,7 | — |
| 8207 30 90 | – – Other | 2,7 | — |
| 8207 40 | – Tools for tapping or threading | ||
| – – For working metal | |||
| 8207 40 10 | – – – Tools for tapping | 2,7 | — |
| 8207 40 30 | – – – Tools for threading | 2,7 | — |
| 8207 40 90 | – – Other | 2,7 | — |
| 8207 50 | – Tools for drilling, other than for rock-drilling | ||
| 8207 50 10 | – – With working part of diamond or agglomerated diamond | 2,7 | — |
| – – With working part of other materials | |||
| 8207 50 30 | – – – Masonry drills | 2,7 | — |
| – – – Other | |||
| – – – – For working metal, with working part | |||
| 8207 50 50 | – – – – – Of cermets | 2,7 | — |
| 8207 50 60 | – – – – – Of high speed steel | 2,7 | — |
| 8207 50 70 | – – – – – Of other materials | 2,7 | — |
| 8207 50 90 | – – – – Other | 2,7 | — |
| 8207 60 | – Tools for boring or broaching | ||
| 8207 60 10 | – – With working part of diamond or agglomerated diamond | 2,7 | — |
| – – With working part of other materials | |||
| – – – Tools for boring | |||
| 8207 60 30 | – – – – For working metal | 2,7 | — |
| 8207 60 50 | – – – – Other | 2,7 | — |
| – – – Tools for broaching | |||
| 8207 60 70 | – – – – For working metal | 2,7 | — |
| 8207 60 90 | – – – – Other | 2,7 | — |
| 8207 70 | – Tools for milling | ||
| – – For working metal, with working part | |||
| 8207 70 10 | – – – Of cermets | 2,7 | — |
| – – – Of other materials | |||
| 8207 70 31 | – – – – Shank type | 2,7 | — |
| 8207 70 37 | – – – – Other | 2,7 | — |
| 8207 70 90 | – – Other | 2,7 | — |
| 8207 80 | – Tools for turning | ||
| – – For working metal, with working part | |||
| 8207 80 11 | – – – Of cermets | 2,7 | — |
| 8207 80 19 | – – – Of other materials | 2,7 | — |
| 8207 80 90 | – – Other | 2,7 | — |
| 8207 90 | – Other interchangeable tools | ||
| 8207 90 10 | – – With working part of diamond or agglomerated diamond | 2,7 | — |
| – – With working part of other materials | |||
| 8207 90 30 | – – – Screwdriver bits | 2,7 | — |
| 8207 90 50 | – – – Gear-cutting tools | 2,7 | — |
| – – – Other, with working part | |||
| – – – – Of cermets | |||
| 8207 90 71 | – – – – – For working metal | 2,7 | — |
| 8207 90 78 | – – – – – Other | 2,7 | — |
| – – – – Of other materials | |||
| 8207 90 91 | – – – – – For working metal | 2,7 | — |
| 8207 90 99 | – – – – – Other | 2,7 | — |
| 8208 | Knives and cutting blades, for machines or for mechanical appliances | ||
| 8208 10 00 | – For metalworking | 1,7 | — |
| 8208 20 00 | – For woodworking | 1,7 | — |
| 8208 30 00 | – For kitchen appliances or for machines used by the food industry | 1,7 | — |
| 8208 40 00 | – For agricultural, horticultural or forestry machines | 1,7 | — |
| 8208 90 00 | – Other | 1,7 | — |
| 8209 00 | Plates, sticks, tips and the like for tools, unmounted, of cermets | ||
| 8209 00 20 | – Indexable inserts | 2,7 | — |
| 8209 00 80 | – Other | 2,7 | — |
| 8210 00 00 | Hand-operated mechanical appliances, weighing 10 kg or less, used in the preparation, conditioning or serving of food or drink | 2,7 | — |
| 8211 | Knives with cutting blades, serrated or not (including pruning knives), other than knives of heading 8208 , and blades therefor | ||
| 8211 10 00 | – Sets of assorted articles | 8,5 | — |
| – Other | |||
| 8211 91 00 | – – Table knives having fixed blades | 8,5 | — |
| 8211 92 00 | – – Other knives having fixed blades | 8,5 | — |
| 8211 93 00 | – – Knives having other than fixed blades | 8,5 | — |
| 8211 94 00 | – – Blades | 6,7 | — |
| 8211 95 00 | – – Handles of base metal | 2,7 | — |
| 8212 | Razors and razor blades (including razor blade blanks in strips) | ||
| 8212 10 | – Razors | ||
| 8212 10 10 | – – Safety razors with non-replaceable blades | 2,7 | p/st |
| 8212 10 90 | – – Other | 2,7 | p/st |
| 8212 20 00 | – Safety razor blades, including razor blade blanks in strips | 2,7 | 1 000 p/st |
| 8212 90 00 | – Other parts | 2,7 | — |
| 8213 00 00 | Scissors, tailors' shears and similar shears, and blades therefor | 4,2 | — |
| 8214 | Other articles of cutlery (for example, hair clippers, butchers' or kitchen cleavers, choppers and mincing knives, paperknives); manicure or pedicure sets and instruments (including nail files) | ||
| 8214 10 00 | – Paperknives, letter openers, erasing knives, pencil sharpeners and blades therefor | 2,7 | — |
| 8214 20 00 | – Manicure or pedicure sets and instruments (including nail files) | 2,7 | — |
| 8214 90 00 | – Other | 2,7 | — |
| 8215 | Spoons, forks, ladles, skimmers, cake-servers, fish-knives, butter-knives, sugar tongs and similar kitchen or tableware | ||
| 8215 10 | – Sets of assorted articles containing at least one article plated with precious metal | ||
| 8215 10 20 | – – Containing only articles plated with precious metal | 4,7 | — |
| – – Other | |||
| 8215 10 30 | – – – Of stainless steel | 8,5 | — |
| 8215 10 80 | – – – Other | 4,7 | — |
| 8215 20 | – Other sets of assorted articles | ||
| 8215 20 10 | – – Of stainless steel | 8,5 | — |
| 8215 20 90 | – – Other | 4,7 | — |
| – Other | |||
| 8215 91 00 | – – Plated with precious metal | 4,7 | — |
| 8215 99 | – – Other | ||
| 8215 99 10 | – – – Of stainless steel | 8,5 | — |
| 8215 99 90 | – – – Other | 4,7 | — |
CHAPTER 83
MISCELLANEOUS ARTICLES OF BASE METAL
Notes
-
- For the purposes of this chapter, parts of base metal are to be classified with their parent articles. However, articles of iron or steel of heading 7312 , 7315 , 7317 , 7318 or 7320 , or similar articles of other base metal (Chapters 74 to 76 and 78 to 81) are not to be taken as parts of articles of this chapter.
-
- For the purposes of heading 8302 , the word ‘castors’ means those having a diameter (including, where appropriate, tyres) not exceeding 75 mm, or those having a diameter (including, where appropriate, tyres) exceeding 75 mm provided that the width of the wheel or tyre fitted thereto is less than 30 mm.
| CN code | Description | Conventional rate of duty (%) | Supplementary unit |
| (1) | (2) | (3) | (4) |
| 8301 | Padlocks and locks (key, combination or electrically operated), of base metal; clasps and frames with clasps, incorporating locks, of base metal; keys for any of the foregoing articles, of base metal | ||
| 8301 10 00 | – Padlocks | 2,7 | — |
| 8301 20 00 | – Locks of a kind used for motor vehicles | 2,7 | — |
| 8301 30 00 | – Locks of a kind used for furniture | 2,7 | — |
| 8301 40 | – Other locks | ||
| – – Locks of a kind used for doors of buildings | |||
| 8301 40 11 | – – – Cylinder | 2,7 | — |
| 8301 40 19 | – – – Other | 2,7 | — |
| 8301 40 90 | – – Other locks | 2,7 | — |
| 8301 50 00 | – Clasps and frames with clasps, incorporating locks | 2,7 | — |
| 8301 60 00 | – Parts | 2,7 | — |
| 8301 70 00 | – Keys presented separately | 2,7 | — |
| 8302 | Base metal mountings, fittings and similar articles suitable for furniture, doors, staircases, windows, blinds, coachwork, saddlery, trunks, chests, caskets or the like; base metal hat-racks, hat-pegs, brackets and similar fixtures; castors with mountings of base metal; automatic door closers of base metal | ||
| 8302 10 00 | – Hinges | 2,7 | — |
| 8302 20 00 | – Castors | 2,7 | — |
| 8302 30 00 | – Other mountings, fittings and similar articles suitable for motor vehicles | 2,7 | — |
| – Other mountings, fittings and similar articles | |||
| 8302 41 | – – Suitable for buildings | ||
| 8302 41 10 | – – – For doors | 2,7 | — |
| 8302 41 50 | – – – For windows and French windows | 2,7 | — |
| 8302 41 90 | – – – Other | 2,7 | — |
| 8302 42 00 | – – Other, suitable for furniture | 2,7 | — |
| 8302 49 00 | – – Other | 2,7 | — |
| 8302 50 00 | – Hat-racks, hat-pegs, brackets and similar fixtures | 2,7 | — |
| 8302 60 00 | – Automatic door closers | 2,7 | — |
| 8303 00 | Armoured or reinforced safes, strongboxes and doors and safe deposit lockers for strong-rooms, cash or deed boxes and the like, of base metal | ||
| 8303 00 40 | – Armoured or reinforced safes, strongboxes and doors and safe deposit lockers for strongrooms | 2,7 | — |
| 8303 00 90 | – Cash or deed boxes and the like | 2,7 | — |
| 8304 00 00 | Filing cabinets, card-index cabinets, paper trays, paper rests, pen trays, office-stamp stands and similar office or desk equipment, of base metal, other than office furniture of heading 9403 | 2,7 | — |
| 8305 | Fittings for loose-leaf binders or files, letter clips, letter corners, paper clips, indexing tags and similar office articles, of base metal; staples in strips (for example, for offices, upholstery, packaging), of base metal | ||
| 8305 10 00 | – Fittings for loose-leaf binders or files | 2,7 | — |
| 8305 20 00 | – Staples in strips | 2,7 | — |
| 8305 90 00 | – Other, including parts | 2,7 | — |
| 8306 | Bells, gongs and the like, non-electric, of base metal; statuettes and other ornaments, of base metal; photograph, picture or similar frames, of base metal; mirrors of base metal | ||
| 8306 10 00 | – Bells, gongs and the like | Free | — |
| – Statuettes and other ornaments | |||
| 8306 21 00 | – – Plated with precious metal | Free | — |
| 8306 29 00 | – – Other | Free | — |
| 8306 30 00 | – Photograph, picture or similar frames; mirrors | 2,7 | — |
| 8307 | Flexible tubing of base metal, with or without fittings | ||
| 8307 10 00 | – Of iron or steel | 2,7 | — |
| 8307 90 00 | – Of other base metal | 2,7 | — |
| 8308 | Clasps, frames with clasps, buckles, buckle-clasps, hooks, eyes, eyelets and the like, of base metal, of a kind used for clothing, footwear, awnings, handbags, travel goods or other made-up articles, tubular or bifurcated rivets, of base metal; beads and spangles of base metal | ||
| 8308 10 00 | – Hooks, eyes and eyelets | 2,7 | — |
| 8308 20 00 | – Tubular or bifurcated rivets | 2,7 | — |
| 8308 90 00 | – Other, including parts | 2,7 | — |
| 8309 | Stoppers, caps and lids (including crown corks, screw caps and pouring stoppers), capsules for bottles, threaded bungs, bung covers, seals and other packing accessories, of base metal | ||
| 8309 10 00 | – Crown corks | 2,7 | — |
| 8309 90 | – Other | ||
| 8309 90 10 | – – Capsules of lead; capsules of aluminium of a diameter exceeding 21 mm | 3,7 | — |
| 8309 90 90 | – – Other | 2,7 | — |
| 8310 00 00 | Sign-plates, nameplates, address-plates and similar plates, numbers, letters and other symbols, of base metal, excluding those of heading 9405 | 2,7 | — |
| 8311 | Wire, rods, tubes, plates, electrodes and similar products, of base metal or of metal carbides, coated or cored with flux material, of a kind used for soldering, brazing, welding or deposition of metal or of metal carbides; wire and rods, of agglomerated base metal powder, used for metal spraying | ||
| 8311 10 00 | – Coated electrodes of base metal, for electric arc-welding | 2,7 | — |
| 8311 20 00 | – Cored wire of base metal, for electric arc-welding | 2,7 | — |
| 8311 30 00 | – Coated rods and cored wire, of base metal, for soldering, brazing or welding by flame | 2,7 | — |
| 8311 90 00 | – Other | 2,7 | — |
SECTION XVI
MACHINERY AND MECHANICAL APPLIANCES; ELECTRICAL EQUIPMENT; PARTS THEREOF; SOUND RECORDERS AND REPRODUCERS, TELEVISION IMAGE AND SOUND RECORDERS AND REPRODUCERS, AND PARTS AND ACCESSORIES OF SUCH ARTICLES
Notes
-
- This section does not cover:
- (a) transmission or conveyor belts or belting, of plastics of Chapter 39, or of vulcanised rubber (heading 4010 ), or other articles of a kind used in machinery or mechanical or electrical appliances or for other technical uses, of vulcanised rubber other than hard rubber (heading 4016 );
- (b) articles of leather or of composition leather (heading 4205 ) or of furskin (heading 4303 ), of a kind used in machinery or mechanical appliances or for other technical uses;
- (c) bobbins, spools, cops, cones, cores, reels or similar supports, of any material (for example, Chapter 39, 40, 44 or 48 or Section XV);
- (d) perforated cards for jacquard or similar machines (for example, Chapter 39 or 48 or Section XV);
- (e) transmission or conveyor belts or belting, of textile material (heading 5910 ) or other articles of textile material for technical uses (heading 5911 );
- (f) precious or semi-precious stones (natural, synthetic or reconstructed) of headings 7102 to 7104 , or articles wholly of such stones of heading 7116 , except unmounted worked sapphires and diamonds for styli (heading 8522 );
- (g) parts of general use, as defined in note 2 to Section XV, of base metal (Section XV), or similar goods of plastics (Chapter 39);
- (h) drill pipe (heading 7304 );
- (ij) endless belts of metal wire or strip (Section XV);
- (k) articles of Chapter 82 or 83;
- (l) articles of Section XVII;
- (m) articles of Chapter 90;
- (n) clocks, watches or other articles of Chapter 91;
- (o) interchangeable tools of heading 8207 or brushes of a kind used as parts of machines (heading 9603 ); similar interchangeable tools are to be classified according to the constituent material of their working part (for example, in Chapter 40, 42, 43, 45 or 59 or heading 6804 or 6909 );
- (p) articles of Chapter 95; or
- (q) typewriter or similar ribbons, whether or not on spools or in cartridges (classified according to their constituent material, or in heading 9612 if inked or otherwise prepared for giving impressions).
-
- Subject to note 1 to this section, note 1 to Chapter 84 and note 1 to Chapter 85, parts of machines (not being parts of the articles of heading 8484 , 8544 , 8545 , 8546 or 8547 ) are to be classified according to the following rules:
- (a) Parts which are goods included in any of the headings of Chapter 84 or 85 (other than headings 8409 , 8431 , 8448 , 8466 , 8473 , 8487 , 8503 , 8522 , 8529 , 8538 and 8548 ) are in all cases to be classified in their respective headings.
- (b) Other parts, if suitable for use solely or principally with a particular kind of machine, or with a number of machines of the same heading (including a machine of heading 8479 or 8543 ) are to be classified with the machines of that kind or in heading 8409 , 8431 , 8448 , 8466 , 8473 , 8503 , 8522 , 8529 or 8538 as appropriate. However, parts which are equally suitable for use principally with the goods of headings 8517 and 8525 to 8528 are to be classified in heading 8517 .
- (c) All other parts are to be classified in heading 8409 , 8431 , 8448 , 8466 , 8473 , 8503 , 8522 , 8529 or 8538 as appropriate or, failing that, in heading 8487 or 8548 .
-
- Unless the context otherwise requires, composite machines consisting of two or more machines fitted together to form a whole and other machines designed for the purpose of performing two or more complementary or alternative functions are to be classified as if consisting only of that component or as being that machine which performs the principal function.
Reading this document does not replace reading the official text published in the Official Journal of the European Union. We assume no responsibility for any inaccuracies arising from the conversion of the original to this format.
This text is published under EUR-Lex's own terms of reuse, not a Legalize or public-domain licence.
EUR-Lex
Creative Commons Attribution 4.0 International (CC BY 4.0)
© European Union, https://eur-lex.europa.eu — Source: EUR-Lex (Publications Office of the European Union). Reused under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Only EU legislation published in the printed Official Journal of the European Union is deemed authentic; consolidated texts are reproduced here for documentation purposes and have been reformatted to Markdown.