Legalize / European Union / Implementing Regulation

Commission Implementing Regulation (EU) 2015/504 of 11 March 2015 implementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to the administrative requirements for the approval and market surveillance of agricultural and forestry vehicles Text with EEA relevance

Type Implementing Regulation

Publication 2015-03-28

Last updated 2018-08-07

State In force

Department European Commission

Source EUR-Lex

articles 14

Reform history JSON API

27.1.1. Requirements under UNECE Regulation 62 (OJ L 89, 27.3.2013, p. 37) are met with the relevant documentation included in the information document: yes/no/not applicable (⁴)

27.1.2. Relevant requirements as prescribed for N2-category vehicles in points 2, 5 except point 5.6, 6.2 and 6.3, under UNECE Regulation No 18 (OJ L 120, 13.5.2010, p. 29) are met with the relevant documentation included in the information document: yes/no/not applicable (⁴)

27.1.3. Alternatively to entry 27.1.1 or entry 27.1.2, provide the following information:

27.1.3.1. Detailed description, including photographs or drawings, of the protective device(s) and of the vehicle parts involved in its installation: …

27.1.3.2. List of the main components comprising the protective device(s): …

27.2. For R- and S-category vehicles

27.2.1. Detailed description, including photographs or drawings, of the protective device(s) and of the vehicle parts involved in its installation: …

27.2.1.1. List of the main components comprising the protective device(s): …

28. REAR REGISTRATION PLATE(S) SPACE

28.1.Location of registration plate(s) (indicate variants where necessary; drawings may be used as appropriate):

28.1.1.Height above road surface, upper edge: …mm

28.1.2.Height above road surface, lower edge: …mm

28.1.3.Distance of the centre line from the longitudinal median plane of the vehicle: …mm

28.1.4.Dimensions (length × width): …mm × …mm

28.1.5.Inclination of the plane to the vertical: …degr.

28.1.6.Angle of visibility in the horizontal plane: ….degr.

29. BALLAST MASSES

29.1.Detailed technical description (including photographs or drawings with dimensions) of the ballast masses and how they are mounted on the tractor:

29.2.Number of sets of ballast masses: …

29.2.1.Number of components on each set: Set 1: … Set 2: …Set …

29.3.Mass of the components on each set: Set 1: …kg Set 2: …kg Set …:…kg

29.3.1.Total mass of each set: Set 1: …kg Set 2: …kg Set …:…kg

29.4.Total mass of ballast masses: …kg

29.4.1.Distribution of these masses among the axles: …kg

29.5.Material(s) and method of construction: …

30. SAFETY OF ELECTRICAL SYSTEMS

30.1. Brief description of the power circuit components installation and drawings/photographs showing the location of the power circuit components installation: …

30.2. Schematic diagram of all electrical functions included in power circuit: …

30.3. Working voltage(s) (V): …

30.4. Description of protection against electric-shocks: …

30.5. Fuse and/or circuit breaker yes/no/optional (⁴)

30.5.1. Diagram showing the functional range: …

30.6. Configuration of power wiring harness: …

30.7. Generator

30.7.1. Type: …

30.7.2. Rated power: … VA

30.8. All-electric vehicles

30.8.1. For all-electric T2-, T3-, C2- or C3-category vehicles, requirements of Annex IV to Commission Delegated Regulation (EU) No 3/2014 are met, with relevant documentation included in the information document: yes/no/as far as practicable (⁴) (if as far as practicable, specify: …)

30.9. Battery isolator

30.9.1. Disconnection of the battery by: electronic system/ignition key/common tool/switch/other (⁴) (if other, specify: …)

31. FUEL TANK(S)

31.1. Drawing and technical description of the tank(s) with connections and lines of the breathing and venting system, locks, valves, fastening devices: …

31.2. Drawing clearly showing the position of the tank(s) in the vehicle: …

31.3. Drawing of the heat shield between tank and exhaust device: …

31.4. Main fuel tank(s)

31.4.1. Maximum capacity: …

31.4.2. Materials used: …

31.4.3. Fuel tank inlet: restricted orifice/label (⁴) …

31.4.4. Measure(s) for charge dissipation (if any): …

31.5. Reserve fuel tank(s)

31.5.1. Maximum capacity: …

31.5.2. Materials used: …

31.5.3. Fuel tank inlet: restricted orifice/label (⁴) …

31.5.4. Measure(s) for charge dissipation (if any): …

32. LATERAL AND REAR PROTECTION

32.1. Lateral protection

32.1.1. Presence: yes/no/incomplete (⁴)

32.1.2. Drawing of the vehicle parts relevant to the lateral protection, i.e. drawing of the vehicle and/or chassis with position and mounting of the axle(s), drawing of the mountings and/or the fittings of lateral protection device(s). If the lateral protection is achieved without lateral protection device(s) the drawing shall clearly show that the required dimensions are met: …

32.1.3. Drawing of the floor line at the vehicle lateral: …

32.1.4. Drawings of the necessary sections through the external surface to measure the height (H) of the external surface projections in accordance with Appendix 1 to Annex XXVII to Commission Delegated Regulation (EU) 2015/208: …

32.1.5. In the case of lateral protection device(s), full description and/or drawing of such device(s) (including mountings and fittings) or its/their component type-approval number(s): …

32.1.5.1. Materials used: …

32.1.5.2. Complete details of fittings required and full instructions, including torque requirements, for fitting: …

32.1.6. Requirements under points 2 and 3 and Parts I, II and III of UNECE Regulation No 73 (OJ L 122, 8.5.2012, p. 1) are met with relevant documentation included in the information document: yes/no (⁴)

32.2. Rear protective structure

32.2.1. Presence: yes/no/incomplete (⁴)

32.2.2. Drawing of the vehicle parts relevant to the rear protective structure, i.e. drawing of the vehicle and/or chassis with position and mounting of the widest rear axle, drawing of the mounting and/or fitting of the rear protective structure. If the rear protective structure is not a special device, the drawing shall clearly show that the required dimensions are met: …

32.2.3. Drawing of the floor line at the vehicle rear end: …

32.2.4. In case of a special device, full description and/or drawing of the rear protective structure (including mountings and fittings), or, if approved as separate technical unit, type-approval number: …

32.2.4.1. Materials used: …

32.2.4.2. Complete details of fittings required and full instructions, including torque requirements, for fitting: …

33. LOAD PLATFORM(S)

33.1. Load platform(s) dimensions

33.1.1. Length of the load platform(s): … mm

33.1.2. Width of load platform(s): … mm

33.1.3. Height of load platform(s) above the ground (⁴⁷): … mm

33.2. Safe load carrying capacity of load platform(s) declared by manufacturer: … kg

33.2.1. Distribution of this (these) load(s) among the axles: … kg

33.3. For T- and C-category vehicles, detachable platform(s): yes/no/optional (⁴)

33.3.1. Description of the devices for attachment to the vehicle: …

33.4. Stability of the load platform

33.4.1. Position of centre of gravity of the platform(s) in the longitudinal, transverse and vertical direction: …

33.4.2. For vehicles with multiple load platforms, position of the centre of gravity of the vehicle with loaded platform(s) and without driver in the longitudinal, transverse and vertical direction: …

34. FRONT TOWING DEVICE (T-AND C-CATEGORY VEHICLES)

34.1. Dimensioned drawing of the front towing device and of the securing device: …

34.2. For vehicles equipped with a maximum technically permissible mass not exceeding 2 000 kg, requirements of Commission (EU) Regulation No 1005/2010 (OJ L 291, 9.11.2010, p. 36) are met, with the relevant documentation included in the information document: yes/no (⁴)

35. TYRES

35.1. Type-approved in accordance with Annex XXX to Commission Delegated Regulation (EU) 2015/208: yes/no/not applicable (⁴)

35.2. Type-approved in accordance with Regulation (EC) No 661/2009 of the European Parliament and of the Council (OJ L 200, 31.7.2009, p. 1): yes/no/not applicable (⁴)

35.3. Approved in accordance with UNECE Regulation No 106 (OJ L 257, 30.9.2010, p. 231): yes/no/not applicable (⁴)

35.4. Approved in accordance with UNECE Regulation No 30 (OJ L 307, 23.11.2011, p. 1): yes/no/not applicable (⁴)

35.5. Approved in accordance with UNECE Regulation No 54 (OJ L 307, 23.11.2011, p. 2): yes/no/not applicable (⁴)

35.6. Approved in accordance with UNECE Regulation No 75 (OJ L 84, 30.3.2011, p. 46): yes/no/not applicable (⁴)

35.7. Approved in accordance with UNECE Regulation No 117 (OJ L 307, 23.11.2011, p. 3): yes/no/not applicable (⁴)

36. SPRAY-SUPPRESSION SYSTEM

36.1. Wheel guards

36.1.1. Vehicle fitted with wheel guards: yes/no (⁴)

36.1.2. Brief description of the vehicle with regard to its wheel guards: …

36.1.3. Detailed drawings of the wheel guards and their position on the vehicle showing the dimensions and taking account of the extremes of tyre/wheel combinations: …

36.2. Other spray-suppression devices

36.2.1. Presence: yes/no/incomplete (⁴)

36.2.2. Brief description of the vehicle with regard to its spray-suppression system and the constituent components: …

36.2.3. Detailed drawings of the spray-suppression system and its position on the vehicle showing the dimensions and taking account of the extremes of tyre/wheel combinations: …

37. CRAWLER UNDERCARRIAGE

(provide also entry 4.1.2.3)

37.1. Photographs and dimensioned drawings of the arrangement of the crawler undercarriage and its installation on the vehicle (including the elements inside of track belts to ensure that the track belt is guided over the rollers and the track pattern in the outside): …

37.2. Type of material in contact with the surface: rubber tracks/steel tracks/rubber pads on the track shoes (⁴)

37.3. Metallic tracks

37.3.1. Number of track rollers directly transferring load onto the road surface (NR): …

37.3.2. Outer surface area of each pad (AP): … mm²

37.4. Rubber tracks

37.4.1. Total surface area of rubber lugs in contact with the road (AL): … mm²

37.4.2. Percentage of lug area versus the total surface of the belt: … %

38. MECHANICAL COUPLING

38.1. Photographs and dimensional drawings of the mechanical coupling, its installation on the vehicle and its coupling with the device installed on the towed vehicle:

38.1.1. Rear mechanical coupling: yes/no (⁴)

38.1.2. Front coupling device (for R- and S-category vehicles): yes/no (⁴)

38.2. Short technical description of the mechanical coupling specifying the type of construction and the material used

38.2.1. Rear mechanical coupling: …

38.2.2. Front coupling device (for R- and S-category vehicles): …

38.3. Rear mechanical coupling


Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	…	…	…
Make:	Make:	Make:	…	…	…
Manufacturer's type designation:	Manufacturer's type designation:	Manufacturer's type designation:	…	…	…
(EU) type-approval mark or -number:	(EU) type-approval mark or -number:	(EU) type-approval mark or -number:	…	…	…
Maximum horizontal load/D-Value (⁴) (⁴⁴):	Maximum horizontal load/D-Value (⁴) (⁴⁴):	Maximum horizontal load/D-Value (⁴) (⁴⁴):	… kg/kN (⁴)	… kg/kN (⁴)	… kg/kN (⁴)
Towable mass (T) (⁴) (⁴⁴):	Towable mass (T) (⁴) (⁴⁴):	Towable mass (T) (⁴) (⁴⁴):	… tonnes	… tonnes	… tonnes
Maximum permissible vertical load on the coupling point (⁴⁴):	Maximum permissible vertical load on the coupling point (⁴⁴):	Maximum permissible vertical load on the coupling point (⁴⁴):	… kg	… kg	… kg
Position of coupling point (⁶²)	height above ground,	minimum	… mm	… mm	… mm
Position of coupling point (⁶²)	height above ground,	maximum	… mm	… mm	… mm
Position of coupling point (⁶²)	distance from vertical plane passing through the axis of the rear axle	minimum	… mm	… mm	… mm
Position of coupling point (⁶²)	distance from vertical plane passing through the axis of the rear axle	maximum	… mm	… mm	… mm

38.4. Front coupling device (for R- and S-category vehicles):


Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	…	…	…
Make:	Make:	Make:	…	…	…
Manufacturer's type designation:	Manufacturer's type designation:	Manufacturer's type designation:	…	…	…
(EU) type-approval mark or -number:	(EU) type-approval mark or -number:	(EU) type-approval mark or -number:	…	…	…
Maximum horizontal load/D-Value (⁴) (⁴⁴):	Maximum horizontal load/D-Value (⁴) (⁴⁴):	Maximum horizontal load/D-Value (⁴) (⁴⁴):	… kg/kN (⁴)	… kg/kN (⁴)	… kg/kN (⁴)
Towable mass (T) (⁴) (⁴⁴):	Towable mass (T) (⁴) (⁴⁴):	Towable mass (T) (⁴) (⁴⁴):	… tonnes	… tonnes	… tonnes
Maximum permissible vertical load on the coupling point (⁴⁴):	Maximum permissible vertical load on the coupling point (⁴⁴):	Maximum permissible vertical load on the coupling point (⁴⁴):	… kg	… kg	… kg
Position of coupling point (⁶²)	height above ground,	minimum	… mm	… mm	… mm
Position of coupling point (⁶²)	height above ground,	maximum	… mm	… mm	… mm

38.5. Description of the mechanical coupling:


Type (according to Appendix 1 of Annex XXXIV to Commission Delegated Regulation (EU) 2015/208):	…
Make:	…
Manufacturer’s type designation:	…
Maximum horizontal load/D-Value (⁴) (⁴⁴):	… kg/kN (⁴)
Towable mass (T) (⁴) (⁴⁴):	… tonnes
Maximum permissible vertical load on the coupling point (S) (⁴⁴):	… kg
Photographs and scale drawings of the coupling device. These drawings shall in particular show the required dimensions in detail as well as the measurements for mounting the device.
Short technical description of the coupling device specifying the type of construction and the material used.
Type of Test	Static/Dynamic (⁴)
(EU) type-approval mark or -number of — drawbar eyes, coupling heads or similar coupling devices that shall be attached to the mechanical coupling (in the case of hinged or rigid drawbars) — type-approval mark or –number of mechanical couplings that shall be attached to the ladder frame /trailer hitch support (if restricted to certain types):	…

38.6. Component type-approval for a mechanical coupling granted under UNECE Regulation No 55 (OJ L 227, 28.8.2010, p. 1), with relevant documentation included in the information document: yes/no/not applicable (⁴)

39. THREE-POINT LIFTING MECHANISM

39.1. Three-point lifting mechanism: front mounted/rear mounted/both front and rear mounted/inexistent (⁴)

39.2. Maximum towable mass (¹⁶): … kg

40. ADDITIONAL COUPLING POINTS

40.1. Additional coupling points: yes/no/optional (⁴)

40.2. Detailed technical description (including photographs or drawings) and main purpose(s) of the additional coupling points: …

40.3. Maximum permissible vertical load on the additional coupling points: … kg

D. INFORMATION ON BRAKING PERFORMANCE

41. SUSPENSION

41.1. Brief description and schematic drawing of suspension and its control system for of each axle or group of axles or wheel: …

41.2. Drawing of the suspension arrangements: …

41.3. Level adjustment: yes/no/optional (⁴)

41.4. Brief description of the electrical/electronic components: …

41.5. Air-suspension for driving axle(s): yes/no (⁴)

41.5.1. Suspension of driving axle(s) equivalent to air-suspension: yes/no (⁴)

41.5.2. Frequency and damping of the oscillation of the sprung mass: …

41.6. Air-suspension for non-driving axle(s): yes/no (⁴)

41.6.1. Suspension of non-driving axle(s) equivalent to air-suspension: yes/no (⁴)

41.6.2. Frequency and damping of the oscillation of the sprung mass: …

41.7. Characteristics of the springing parts of the suspension (design, characteristics of the materials and dimensions): …

41.8. Vehicle equipped with hydro-pneumatic/hydraulic/pneumatic (⁴) suspension: yes/no (⁴)

41.9. Stabilisers: yes/no/optional (⁴)

41.10. Shock absorbers: yes/no/optional (⁴)

41.11. Other devices (if any): …

42. AXLE(S) AND TYRES

42.1. Description (including photographs and drawings) of the axle(s): …

42.2. Material(s) and method of construction: …

42.3. Make (where appropriate): …

42.4. Type (where appropriate): …

42.5. Maximum permissible mass supported by the axle(s): … kg

42.6. Axle(s) dimensions:

42.6.1. Length: … mm

42.6.2. Width: … mm

42.7. Braking connection to the axle(s): axial/radial/integrated/other (⁴) (if other, specify: …)

42.8. Dimensions of the largest permissible tyres on braked axles: …

42.8.1. Nominal rolling circumference of the largest tyres on braked axles: …

42.8.2. Dimensions of the largest permissible tyres on powered axles: …

42.8.3. Nominal rolling circumference of the of the largest tyres on powered axles: …

43. BRAKING

43.1. Brief description of the braking system(s) installed on the vehicle (⁵⁵): …

43.2.Specifications of the vehicle with respect to the control circuits of the pneumatic, hydraulic and/or electric control lines of the braking system(s) and a list of the supported messages and parameters: …

43.4. Braking system(s)

43.4.1. Description of the braking system(s) operation (including any electronic parts), electric block diagram, hydraulic or pneumatic circuit plan (⁵⁵): …

43.4.2 Schematic drawing and operating sketch of the braking system(s) (⁵⁵): …

43.4.3. List of braking-system components, properly identified (⁵⁵): …

43.4.4. Technical explanation on the calculation for the braking system(s) (determination of the ratio of the total braking forces at the circumference of the wheels to the force applied to the braking control) (⁵⁵): …

43.4.5. External energy source(s) (if any) (characteristics, capacity of energy reservoirs, maximum and minimum pressure, pressure gauge and minimum-pressure warning device on the dashboard, vacuum reservoirs and supply valve, supply compressors, compliance with provisions regarding pressure equipment) (⁵⁵): …

43.4.6. Electronic braking system: yes/no/optional (⁴)

43.4.7. Type-I test report number(s), in accordance with Annex VII to Commission Delegated Regulation (EU) 2015/68 (if applicable): …

43.5. Braking transmission (on towing vehicle)

43.5.1. Braking transmission of the service braking system on towing vehicle: mechanical/pneumatic/hydraulic/hydrostatic/without power assistance/power-assisted/fully powered transmission (⁴)

43.5.2. Transmission technology: pneumatic/hydraulic/both pneumatic and hydraulic (⁴)

43.5.3.Locking of left and right braking controls: yes/no (⁴)

43.6. Towed vehicle braking control devices (on towing vehicle)

43.6.1.Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/None (⁴)

43.6.2.Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …

43.6.2.1.Pneumatic connection type: Two lines/None (⁴)

43.6.2.1.1.Pneumatic supply pressure (two lines): … kPa

43.6.2.1.2.Electrical control line: yes/no (⁴)

43.6.2.2.Hydraulic connection type: Single line / Two lines / None (⁴)

43.6.2.2.1.Hydraulic supply pressure: Single line: … kPa Two lines: … kPa

43.6.2.2.2.Presence of ISO 7638:2003 connector (¹⁵): yes/no (⁴)

43.7. Towed vehicle braking devices (on towed vehicle)

43.7.1. Towed vehicle braking control system technology: Hydraulic / Pneumatic / Electric/ Inertia / None (⁴)

43.7.2. Towed vehicle-brake actuating device: Drum / Disc / Other (⁴)

43.7.2.1. Description and characteristics: …

43.7.3. Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): …

43.7.3.1. Pneumatic connection type: Two lines/None (⁴)

43.7.3.1.1. Electrical control line: yes/no (⁴)

43.7.3.2. Hydraulic connection type: Two lines / None (⁴)

43.7.3.2.1. Presence of ISO 7638:2003 connector (¹⁵): yes/no (⁴)

43.A. TOWED VEHICLE AXLE AND BRAKE INFORMATION DOCUMENT WITH RESPECT TO THE ALTERNATIVE TYPE I AND TYPE III PROCEDURE

43.A.1.General

43.A.1.1.Name and address of axle or vehicle manufacturer:

43.A.2.Axle data

43.A.2.1.Manufacturer (name and address): …

43.A.2.2.Type/variant: …

43.A.2.3.Axle identifier: ID1- …

43.A.2.4.Test axle load (Fe): … daN

43.A.2.5.Wheel and brake data according to the following figures 1A and 1B …

43.A.3.Brake

43.A.3.1.General information

43.A.3.1.1.Make:

43.A.3.1.2.Manufacturer (name and address):

43.A.3.1.3.Type of brake (e.g. drum / disc):

43.A.3.1.3.1.Variant (e.g. S-cam, single wedge etc.):

43.A.3.1.4.Brake identifier: ID2-

43.A.3.1.5.Brake data according to the figures 2A and 2B:

43.A.3.2.Drum brake data

43.A.3.2.1.Brake adjustment device (external/integrated): …

43.A.3.2.2.Declared maximum brake input torque Cmax: … Nm

43.A.3.2.3.Mechanical efficiency: η = …

43.A.3.2.4.Declared brake input threshold torque C0,dec: … Nm

43.A.3.2.5.Effective length of the cam shaft: … mm

43.A.3.3.Brake drum

43.A.3.3.1.Max diameter of friction surface (wear limit) … mm

43.A.3.3.2.Base material: …

43.A.3.3.3.Declared mass: … kg

43.A.3.3.4.Nominal mass: … kg

43.A.3.4.Brake lining

43.A.3.4.1.Manufacturer and address …

43.A.3.4.2.Make …

43.A.3.4.3.Type …

43.A.3.4.4.Identification (type identification on lining) …

43.A.3.4.5.Minimum thickness (wear limit) … mm

43.A.3.4.6.Method of attaching friction material to brake shoe: …

43.A.3.4.6.1.… Worst case of attachment (in the case of more than one):

43.A.3.5.Disc brake data

43.A.3.5.1.Connection type to the axle (axial, radial, integrated, etc.): …

43.A.3.5.2.Brake adjustment device (external/integrated): …

43.A.3.5.3.Max. actuation stroke: … mm

43.A.3.5.4.Declared maximum input force ThAmax: … daN

43.A.3.5.4.1Cmax = ThAmax · le : … Nm

43.A.3.5.5.Friction radius: re = … mm

43.A.3.5.6.Lever length: le = … mm

43.A.3.5.7.Input/output ratio (le/ee): i = ….

43.A.3.5.8.Mechanical efficiency: η = …

43.A.3.5.9.Declared brake input threshold force ThA0,dec: … N

43.A.3.5.9.1.C0,dec = ThA0,dec · le : … Nm

43.A.3.5.10.Minimum rotor thickness (wear limit): … mm

43.A.3.6.Brake disc data …

43.A.3.6.1.Disc type description: …

43.A.3.6.2.Connection/mounting to the hub: …

43.A.3.6.3.Ventilation (yes/no): …

43.A.3.6.4.Declared mass: … kg

43.A.3.6.5.Nominal mass: … kg

43.A.3.6.6.Declared external diameter: … mm

43.A.3.6.7.Minimum external diameter: … mm

43.A.3.6.8.Inner diameter of friction ring: … mm

43.A.3.6.9.Width of ventilation channel (if appl.): … mm

43.A.3.6.10.Base material: …

43.A.3.7.Brake pad data …

43.A.3.7.1.Manufacturer and address: …

43.A.3.7.2.Make:

43.A.3.7.3.Type: …

43.A.3.7.4.Identification (type identification on pad back plate): …

43.A.3.7.5.Minimum thickness (wear limit): … mm

43.A.3.7.6.Method of attaching friction material to pad back plate: …

43.A.3.7.6.1.Worst case of attachment (in the case of more than one): …

Figure 1A

Image omitted; see official source

Figure 1B

Image omitted; see official source

Figure 2A

Image omitted; see official source

Figure 2B

Image omitted; see official source

xe (mm)	ae (mm)	he (mm)	ce (mm)	de (mm)	ee (mm)	α0e	α1e	be (mm)	re (mm)	Ae (cm2)	S1e (mm)	S2e (mm)	S3e (mm)

E. INFORMATION ON VEHICLE CONSTRUCTION

44. CONFORMITY OF PRODUCTION

44.1. Description of overall quality-assurance management systems: …

45. ACCESS TO VEHICLE ON BOARD DIAGNOSTIC (OBD) AND VEHICLE REPAIR AND MAINTENANCE INFORMATION (⁴⁵)

45.1. Address of principal website for access to vehicle repair and maintenance information (⁴⁵): …

45.2. In the case of multi-stage type-approval, address of principal website for access to vehicle repair and maintenance information from manufacturer(s) at previous stage(s) (⁴⁵): …

45.3. Relevant information to enable the development of replacement components which are critical to the correct functioning of the OBD system provided: yes/no (⁴)

45.4. Annual worldwide production of a type (⁶¹): …

45.5. Proof(s) of compliance that vehicle repair and maintenance information is provided using only open text and graphic formats or formats which can be viewed and printed using only standard software plug-ins that are freely available, easy to install, and which run with computer operating systems commonly in use.

45.5.1. Keywords in the metadata conform to ISO 15031-2:2010 (Road vehicles — Communication between vehicle and external equipment for emissions-related diagnostics — Part 2: Guidance on terms, definitions, abbreviations and acronyms): yes/no (⁴)

45.6. Reprogramming of control units in accordance with point 2.5 of Appendix 1 to Annex V to Commission Delegated Regulation (EU) No 1322/2014

45.6.1. Reprogramming of control units conducted in accordance with: /SAE J2534/TMC RP1210/other non-proprietary software (⁴) (if other non-proprietary software, specify: …)

45.6.1.1. Proprietary software: yes/no (⁴)

45.6.1.2. ISO 22900-2 (Road vehicles — Modular vehicle communication interface (MVCI) — Part 2: Diagnostic protocol data unit application programming interface (D-PDU API)): yes/no (⁴)

45.6.1.3. SAE J2534 (Recommended practice for pass-thru vehicle programming): yes/no (⁴)

45.6.1.4. TMC RP1210 (API): yes/no (⁴)

45.6.1.5. Other non-proprietary software: yes/no (⁴) (if other non-proprietary software, specify: …)

45.6.2. Compatibility validation of manufacturer-specific application and vehicle communication interfaces (VCIs) is made by: independently developed VCIs/loan of special hardware (⁴)

45.6.3. In-vehicle communication and communication between ECUs and diagnostic service according to standard:

45.6.3.1.SAE J1939-13 (Serial control and communications vehicle network): yes/no (⁴)

45.6.3.2.ISO 11783-2 (Tractors and machinery for agriculture and forestry – Serial control and communications data network): yes/no (⁴)

45.6.3.3.ISO 15031-3 (Road vehicles – Communication between vehicle and external equipment for emissions-related diagnostics): yes/no (⁴)

45.6.3.4.ISO 13400-4 (Road vehicles – Diagnostic communication over Internet Protocol (DoIP)) (⁴): yes/no (⁴)

45.7. Information required for the manufacture of diagnostic tools

45.7.1. The vehicle manufacturer uses diagnostic and test tools in accordance with ISO 22900-2:2009 (Road vehicles — Modular vehicle communication interface (MVCI) — Part 2: Diagnostic protocol data unit application programming interface (D-PDU API)) and ISO 22901-2:2011 (Road vehicles — Open diagnostic data exchange (ODX) — Part 2: Emissions-related diagnostic data) in their franchised networks: yes/no/not applicable (⁴) (if not applicable: specify reasons: …)

45.7.2. ODX files are accessible to independent operators via the manufacturer's website: yes/no/not applicable (⁴) (if not applicable: specify reasons: …)

45.7.3. Communication protocol information as laid down in point 1.1 of Appendix 2 to Annex V to Commission Delegated Regulation (EU) No 1322/2014 are made available through manufacturer's repair information websites: yes/no/not applicable (⁴) (if not applicable: specify reasons: …)

45.7.4. Information required for the test and diagnosis of OBD monitored components as laid down in point 1.2 of Appendix 2 to Annex V to Commission Delegated Regulation (EU) No 1322/2014 is made available through manufacturer's repair information websites: yes/no/not applicable (⁴) (if not applicable: specify reasons: …)

45.7.5. Data required to perform the repair as laid down in point 1.3 of Appendix 2 to Annex V to Commission Delegated Regulation (EU) No 1322/2014 are made available through manufacturer's repair information websites: yes/no/not applicable (⁴) (if not applicable: specify reasons: …)

45.8. Repair and maintenance information of vehicle combinations

45.8.1 The vehicle manufacturer recommends the combination of a type of tractor with a type of R or S category vehicle or vice versa: yes/no (⁴)

45.8.2. Vehicles for which the combination is recommended:

45.8.2.1. Make (trade name of manufacturer) (¹⁸): …

45.8.2.2. Type (¹⁷): …

45.8.2.2.1. Variant(s) (¹⁷): …

45.8.2.2.2. Version(s) (¹⁷): …

45.8.2.3. Commercial name(s) (if available): …

45.8.2.4. Category, subcategory and speed index of the vehicle (²): …

45.8.3. Vehicle OBD and vehicle repair and maintenance information related to the interconnectivity of both vehicles provided through a website set up jointly by several manufacturers or a consortium of manufacturers: yes/no (⁴)

45.8.3.1. Address of the website set up jointly by several manufacturers or a consortium of manufacturers (⁴⁵): …

46. ROLL-OVER PROTECTIVE STRUCTURE (ROPS)

46.1. Equipment of ROPS: compulsory/optional/standard (⁴)

46.2. ROPS by cab/by frame/by roll bar(s) mounted at front/rear (⁴)

46.2.1. In the case of roll bar: foldable/not foldable (⁴)

46.2.2. In the case of foldable roll bar:

46.2.2.1.Folding operation: non-assisted / partially assisted / fully assisted (⁴)

46.2.2.2.In case of non-assisted or partially assisted folding operation:

46.2.2.2.1.Hand-operated foldable ROPS: with tools/ without tools (⁴)

46.2.2.2.2.Photographs and detailed technical drawings showing the grasping area and a lateral and top view of the accessible zones. Dimensions and maximum forces for actuating the ROPS must figure on the drawings: …

46.2.2.3.In case of partially assisted or fully assisted folding operation, brief description of the assistance devices as well as of their control devices, if any, and their location: …

46.2.2.4.Locking mechanism: manual/automatic (⁴)

46.2.2.4.1.For manual locking mechanisms, brief description of the locking mechanism and of its ergonomic design to avoid pinching or shearing hazards and to limit the force required for its operation: …

46.2.2.4.2.For automatic locking mechanisms,

46.2.2.4.2.1.Brief description of the locking mechanism, its control devices, if any, and their location: …

46.2.2.4.2.2.Manufacturers' certificate set out in Note 2 of point 5.5. of Part B3 of Annex IX to Commission Delegated Regulation (EU) No 1322/2014: yes/no (⁴)

46.3. Photographs and detailed technical drawings showing the position of the ROPS, position of the seat index point (SIP), the details of mountings and position of the front part of the tractor capable of supporting the tractor when overturned (if necessary) etc. (in the case of front-mounted foldable ROPS, show the grasping area and a lateral and top view of the accessible zones). The main dimensions must figure on the drawings, including external dimensions of tractor with protective structure fitted and main interior dimensions: …

46.4. Brief description of the protective structure, comprising:

46.4.1. Type of construction: …

46.4.2. Details of mountings: …

46.4.3. Details of the front part of the tractor capable of supporting the tractor when overturned (if necessary): …

46.4.4. Additional frame: …

46.5. Dimensions (⁵²)

46.5.1. Height of roof members above the seat index point (SIP): … mm

46.5.2. Height of roof members above the tractor footplate: … mm

46.5.3. Interior width of the protective structure vertically above the seat index point at the level of centre of the steering wheel: … mm

46.5.4. Distance from the centre of the steering wheel to the right-hand side of the protective structure: … mm

46.5.5. Distance from the centre of the steering wheel to the left-hand side of the protective structure: … mm

46.5.6. Minimum distance from the steering wheel rim to the protective structure: … mm

46.5.7. Horizontal distance from the seat index point to the rear of the protective structure above the seat index point: … mm

46.5.8. Position (with reference to the rear axle) of the front part of the tractor capable of supporting the tractor when overturned (if necessary):

46.5.8.1. Horizontal distance: … mm

46.5.8.2. Vertical distance: … mm

46.6. Details of materials used in the construction of the protective structure and specifications of steels used (⁵³)

46.6.1. Main frame (parts — material — sizes): …

46.6.2. Mountings (parts — material — sizes): …

46.6.3. Assembly and mounting bolts (parts — sizes): …

46.6.4. Roof (parts — material — sizes): …

46.6.5. Cladding (if equipped) (parts — material — sizes): …

46.6.6. Glass (if equipped) (parts — material — sizes): …

46.6.7. Front part of the tractor capable of supporting the tractor when overturned (if necessary) (parts — material — sizes): …

46.7. Alternatively to entries 46.1 to 46.6.7, provide the following information:

46.7.1. Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (dynamic test), OECD Code 3, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

46.7.2. Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry track-laying tractors, OECD Code 8, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

46.7.3. Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (static test), OECD Code 4, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

46.7.4. Complete test report issued on the basis of the OECD standard Code for the official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 6, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

46.7.5. Complete test report issued on the basis of the OECD standard Code for the official testing of rear mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 7, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

47. FALLING OBJECT PROTECTIVE STRUCTURES (FOPS)

47.1. T- and C-category vehicles equipped for forestry applications

47.1.1. Requirements under standard ISO 8083:2006 (Machinery for forestry — Falling-object protective structures (FOPS) — Laboratory tests and performance requirements) level I/level II (⁴) on FOPS are met with relevant documentation included in the information document: yes/no (⁴)

47.2. All other T- and C-category vehicles fitted with FOPS

47.2.1. Photographs and detailed technical drawings showing the position of the FOPS, position of the seat index point (SIP), etc. The main dimensions must figure on the drawings, including external dimensions of tractor with protective structure fitted and main interior dimensions:

47.2.2. Brief description of the protective structure, comprising:

47.2.2.1. Type of construction: …

47.2.2.2. Details of mountings: …

47.2.3. Dimensions (⁵²)

47.2.3.1. Height of roof members above the seat index point (SIP): … mm

47.2.3.2. Height of roof members above the tractor footplate: … mm

47.2.3.3. Overall height of the tractor with the protective structure fitted: … mm

47.2.3.4. Overall width of the protective structure (if mudguards are included, this is to be stated): … mm

47.2.4. Details of materials used in the construction of the protective structure and specifications of steels used (⁵³)

47.2.4.1. Main frame (parts — material — sizes): …

47.2.4.2. Mountings (parts — material — sizes): …

47.2.4.3. Assembly and mounting bolts (parts — sizes): …

47.2.4.4. Roof (parts — material — sizes): …

47.2.5. Details of tractor manufacturer's reinforcements on original parts: …

47.2.6. Alternatively to entries 47.2.1 to 47.2.5, a complete test report issued on the basis of the OECD standard Code for the official testing of falling object protective structures on agricultural and forestry tractors, OECD Code 10, Edition 2015 of July 2014 is provided with relevant documentation included in the information document: yes/no (⁴)

48. DRIVER'S EXPOSURE TO NOISE LEVEL

48.1. T- or C-category (with rubber tracks) vehicles to be tested in accordance with Test method 1, in accordance with point 2 of Annex XIII to Commission Delegated Regulation (EU) No 1322/2014: yes/no/not applicable (⁴)

48.2. T- or C-category (with rubber tracks) vehicles to be tested in accordance with Test method 2, in accordance with point 3 of Annex XIII to Commission Delegated Regulation (EU) No 1322/2014: yes/no/not applicable (⁴)

48.3. C-category vehicles with steel tracks to be tested on a layer of humid sand as specified by paragraph 5.3.2 of ISO 6395:2008 (Earth-moving machinery — Determination of sound power level — Dynamic test conditions): yes/no/not applicable (⁴)

48.4. Alternatively to entries 48.1 to 48.3, a complete test report issued on the basis of the OECD standard Code for the official measurement of noise at the driving position(s) on agricultural and forestry tractors, OECD Code 5, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

49. SEATING POSITIONS (SADDLES AND SEATS)

49.1. Seating position configuration: seat/saddle (⁴)

49.2. Coordinates or drawing of the Seat Reference point(s) (S) of all seating positions: …

49.3. Description and drawings of:

49.3.1. The seats and their anchorages: …

49.3.2. The adjustment system: …

49.3.3. The displacement and locking systems: …

49.3.4. The seat-belt anchorages (if incorporated in the seat structure): …

49.3.5. The parts of the vehicle used as anchorages: …

49.4. Driver's seat

49.4.1. Position of the driving seat: left/right/centre (⁴)

49.4.2. Driver's seat type category: category A class I/II/III, category B (⁴)

49.4.3. Reversible driving position: yes/no (⁴)

49.4.3.1. Description of the reversible driving position: …

49.4.4. Dimensions of the driving seat, including the depth and width of the seat surface, the position and inclination of the backrest, as well as the inclination of the seat surface:

49.4.5. Main characteristics of the driving seat: …

49.4.6. Adjustment system: …

49.4.7. Displacement and locking system in the longitudinal and vertical directions: …

49.4.7.1. In the case of vehicles not equipped with an adjustable seat, indicate the displacement of the steering column and pedal(s): …

49.5. Passenger seat(s)

49.5.1.Number of passenger seats: …

49.5.2.Location and arrangement (⁸): …

49.5.3.Dimensions of the passenger seat(s): …

49.5.4.Main characteristics of the passenger seat(s): …

49.5.5.Requirements under standard EN 15694:2009 (Agricultural and forestry tractors. Passenger seat. Requirements and test procedures) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

49.5.6.Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs - Quads). Safety requirements and test methods) on passenger seats for ATV Type II vehicle are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

50. OPERATING SPACE AND ACCESS TO AND EXIT OF THE VEHICLE INCLUDING DOORS AND WINDOWS

50.1. Operating space

50.1.1. Detailed photographs or drawings, including dimensions of the operating space, indicating in particular the position of the Seat reference point (S) and the dimensions of the operating space around it, the clearance between the base of the steering wheel and the fixed parts of the tractor, the locations of the control devices, rungs and necessary handrails: …

50.1.2. Hand-operated control devices have the minimum clearances required by point 4.5.3 of ISO 4254-1:2013 (Agricultural machinery — Safety — Part 1: General requirements) with relevant documentation included in the information document: yes/no (⁴)

50.2. Access to the driving position:

50.2.1. Detailed photographs or drawings and/or an exploded view, including dimensions of entrances, steps, rungs, handrails and handholds: …

50.2.2. Minimum dimensions of steps, integral foot recesses and rungs:

50.2.2.1. Depth clearance: … mm

50.2.2.2. Width clearance: … mm

50.2.2.3. Height clearance: … mm

50.2.2.4. Distance between surface of two steps: … mm

50.2.3. For C-category vehicles, requirements under section 3.3.5 of Annex XV to Commission Delegated Regulation (EU) No 1322/2014 are met with relevant documentation included in the information document: yes/no (⁴)

50.2.4. Handrails/handholds (⁴) provided: yes/no (⁴)

50.3. Access to other positions than the driving position:

50.3.1. Detailed photographs or drawings and/or an exploded view, including dimensions of entrances, steps, rungs, handrails and handholds: …

50.3.2. Minimum dimensions of steps, integral foot recesses and rungs:

50.3.2.1. Depth clearance: … mm

50.3.2.2. Width clearance: … mm

50.3.2.3. Height clearance: … mm

50.3.2.4. Distance between surface of two steps: … mm

50.3.3. Handrails/handholds (⁴) provided: yes/no (⁴)

50.4. Occupant doors, latches and hinges

50.4.1. Number of doors, and its configuration, dimensions and maximum angle of opening (⁵): …

50.4.2. Drawing of latches and hinges and of their position in the doors: …

50.4.3. Technical description of latches and hinges: …

50.4.4. Vehicle doors, with powered windows and powered roof hatches, if fitted, complying with paragraphs 5.8.1 to 5.8.5 of UNECE Regulation No 21(OJ L 188, 16.7.2008, p. 32): yes/no (⁴)

50.5. Windows and emergency exit(s)

50.5.1. Photographs or drawings and/or an exploded view of the arrangement of windows and emergency exits, as well as of any additional means to facilitate the evacuation: …

50.5.2. Number of windows: … and of emergency exits: …

50.5.3. Dimensions of windows: … mm × … mm and of emergency exits: … mm × … mm

50.5.4. Means to overcome differences in height exceeding 1 000 mm to facilitate the evacuation, if fitted: …

51. POWER TAKE-OFF(S)

51.1. Number of power take-offs: …

51.2. Main power take-off

51.2.1.Position: front/rear/other (⁴) (if other specify: …)

51.2.2.Revolutions per minute: … min^–1

51.2.2.1.Ratio of power take-off revolutions to that of the engine: …

51.2.3.Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2 (⁵⁷) or ISO 789-1:1990 (Agricultural tractors – Test procedures – Part 1: Power tests for power take-off))

Rated speed PTO (min^–1)	Corresponding engine speed (min^–1)	Power (kW)
1-540	…	…
2-1 000	…	…
540E
1 000 E

51.2.4.Power take-off guard (description, dimensions, drawings, photographs): …

51.3. Secondary power take-off (if any)

51.3.1. Position: front/rear/other (⁴) (if other specify: …)

51.3.2. Revolutions per minute: …

51.3.2.1. Ratio of power take-off revolutions to that of the engine: …

51.3.3. Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2 (⁵⁷) or ISO 789-1:1990 (Agricultural tractors – Test procedures – Part 1: Power tests for power take-off))

Rated speed PTO (min^–1)	Corresponding engine speed (min^–1)	Power (kW)
1-540	…	…
2-1 000	…	…
540E
1 000 E

51.3.4. Power take-off guard(s) (description, dimensions, drawings, photographs): …

51.4. Rear power take-off

51.4.1. Requirements under standard ISO 500-1:2014 (Agricultural tractors — Rear-mounted power take-off types 1, 2, 3 and 4 — Part 1: General specifications, safety requirements, dimensions for master shield and clearance zone) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

51.4.2. Requirements under standard ISO 500-2:2004 (Agricultural tractors — Rear-mounted power take-off types 1, 2 and 3 — Part 2: Narrow-track tractors, dimensions for master shield and clearance zone) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

51.5. Front power take-off

51.5.1. Requirements under standard ISO 8759-1:1998 (Agricultural wheeled tractors — Front-mounted equipment — Part 1: Power take-off and three-point linkage), with the exception of its clause 4.2, are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

52. PROTECTION OF DRIVE COMPONENTS, EXHAUST SYSTEM, GUARDS AND PROTECTIVE DEVICES

52.1. Description (including drawings, sketches or photos) of the protection devices with dimensions showing the safety distances for avoiding contact with dangerous parts and the protective devices fitted for protection on dangerous points, at least for the following components:

52.1.1. Control devices: …

52.1.2. Rear three point lifting mechanism: …

52.1.3. Front three point lifting mechanism: …

52.1.4. Driving seat and environment: …

52.1.5. Passenger seat(s) (if any): …

52.1.6. Steering and swing axle: …

52.1.7. Transmission shafts fixed on the tractor: …

52.1.8. Clearance zone around the drive wheels: …

52.1.9. Engine hood: …

52.1.10. Protection against hot surfaces: …

52.1.11. Exhaust system: …

52.1.12. Wheels: …

52.2. Description (including photographs and drawings, if necessary) of the protective devices employed for:

52.2.1. Single surface protection: …

52.2.2. Multi-surface protection: …

52.2.3. Protection by total encapsulation: …

52.2.4. Brief description of the electrical/electronic components (if any): …

52.3. Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs — Quads). Safety requirements and test methods) on hot surfaces are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

52.4. Description (including drawings, sketches or photos) of the layout and marking of flexible hydraulic hoses: …

52.5. For R-category vehicles with tipping capability, description (including drawings, sketches or photos) of the support devices for service and maintenance: …

52.6. Description and identification (including drawings, sketches or photos) of the greasing points and the means to access them: …

53. SEAT-BELT ANCHORAGES

53.1. Requirements under standard ISO 3776-1:2006 (Tractors and machinery for agriculture — Seat belts — Part 1: Anchorage location requirements) are met with relevant documentation included in the information document: yes/no (⁴)

53.2. Photographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages: …

53.3. Drawings of the anchorages and the parts of the vehicle structure to which they are attached (together with a statement on the nature of the materials used): …

53.4. Designation of the types of belts (¹⁴) authorised for attachment to the anchorages on the vehicles

					Anchorage location	Anchorage location
					Vehicle structure	Seat structure
Driver's seat	Image omitted; see official source	Lower anchorages	Image omitted; see official source	outboard inboard
Driver's seat	Image omitted; see official source	Upper anchorages
Passenger seat 1	Image omitted; see official source	Lower anchorages	Image omitted; see official source	outboard inboard
Passenger seat 1	Image omitted; see official source	Upper anchorages
Passenger seat …	Image omitted; see official source	Lower anchorages	Image omitted; see official source	outboard inboard
Passenger seat …	Image omitted; see official source	Upper anchorages

53.4.1. Observation: …

53.5. Special devices (example: seat-height adjustment, preloading device, etc.): …

53.6. Description of a particular type of safety belt where an anchorage is located in the seat backrest or incorporates an energy dissipating device: …

53.7. Alternative to entries 53.2 to 53.6.

53.7.1. Requirements under standard ISO 3776-2:2013 (Tractors and machinery for agriculture — Seat belts — Part 2: Anchorage strength requirements) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

53.7.2. Test report granted a on the basis of UNECE Regulation No 14 (OJ L 109, 28.4.2011, p. 1) with relevant documentation included in the information document: yes/no/not applicable (⁴)

53.7.3. Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (dynamic test), OECD Code 3 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

53.7.4. Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry track-laying tractors, OECD Code 8 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

53.7.5. Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (static test), OECD Code 4 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

53.7.6. Complete test report issued on the basis of the OECD standard Code for the official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 6 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

53.7.7 Complete test report issued on the basis of the OECD standard Code for the official testing of rear mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 7 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable (⁴)

54. SAFETY BELTS

54.1. Requirements under standard ISO 3776-3:2009 (Tractors and machinery for agriculture — Seat belts — Part 3: Requirements for assemblies) are met with relevant documentation included in the information document: yes/no (⁴)

54.2. Test report granted a on the basis of UNECE Regulation No 16 (OJ L 233, 9.9.2011, p. 1) with relevant documentation included in the information document: yes/no (⁴)

54.3. Number and position of safety belts and seats on which they can be used, please fill out table below:

Safety belt configuration and associated information

			Complete EU type-approval mark / ECE type-approval mark	Variant, if applicable	Belt adjustment device for height (indicate yes/no/optional)
Driver's seat		L
Driver's seat		C
Driver's seat		R
Passenger seat 1		L
Passenger seat 1		C
Passenger seat 1		R
Passenger seat …		L
Passenger seat …		C
Passenger seat …		R
L = left, C = centre, R = right	L = left, C = centre, R = right	L = left, C = centre, R = right	L = left, C = centre, R = right	L = left, C = centre, R = right	L = left, C = centre, R = right

54.4. Brief description of electrical/electronic components: …

55. PROTECTION AGAINST PENETRATING OBJECTS (OPS)

55.1. T- and C-category vehicles equipped for forestry applications

55.1.1. Requirements under ISO 8084:2003 (Machinery for forestry — Operator protective structures — Laboratory tests and performance requirements) are met with relevant documentation included in the information document: yes/no (⁴)

55.2. All other T- and C-category vehicles fitted with OPS

55.2.1. Requirements under Annex 14 to UNECE Regulation 43 (OJ L 230, 31.8.2010, p. 119) on safety glazing are met with the relevant documentation included in the information document: yes/no (⁴)

56. OPERATOR'S MANUAL, INFORMATION WARNINGS AND MARKINGS

56.1. Operator's manual

56.1.1. Requirements under ISO 3600:1996 (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Operator's manuals — Content and presentation), with the exception of section 4.3 (Machine identification), are met: yes/no (⁴)

56.1.2. Information requested under Annex XXII to Commission Delegated Regulation (EU) No 1322/2014 is provided in the operator's manual: yes/no (⁴)

56.2. Information, warnings and markings

56.2.1. Requirements under ISO 3767 Parts 1 (1998+A2:2012) (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 1: Common symbols) and, if applicable, Part 2 (:2008) (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 2: Symbols for agricultural tractors and machinery) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

56.2.2. Alternatively to entry 56.2.1, requirements under UNECE Regulation No 60 (OJ L 95, 31.3.2004, p. 10) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

56.2.3. Requirements under ISO 11684:1995 (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Safety signs and hazard pictorials — General principles) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

56.2.4. Requirements under ISO 7010:2011 (Graphical symbols — Safety colours and safety signs — Registered safety signs) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

56.3. Description, colour coding and means for the identification of flow directions of hydraulic couplings (including drawings, sketches or photos): …

56.4. Description, colour coding and means of identification of safe jacking points (including drawings, sketches or photos): …

57. DRIVER-OPERATED CONTROL DEVICES INCLUDING IDENTIFICATION OF CONTROL DEVICES, TELL-TALES AND INDICATORS

57.1. Photographs and/or drawings of the arrangement of symbols and controls, tell-tales and indicators:

57.2. Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and symbols to be used for that purpose

Symbol No	Device	Control / indicator available [^E0020]	Identified by symbol [^E0020]	Where [^E0021]	Tell-tale available [^E0020]	Identified by symbol [^E0020]	Where [^E0021]
1	Dipped-beam head lamps
2	Main-beam head lamps
3	Position (side) lamps
4	Front fog lamps
5	Rear fog lamp
6	Headlamp levelling device
7	Parking lamps
8	Direction indicators
9	Hazard warning
10	Windscreen wiper
11	Windscreen washer
12	Windscreen wiper and washer
13	Headlamp cleaning device
14	Windscreen demisting and defrosting
15	Rear window demisting and defrosting
16	Ventilating fan
17	Diesel pre-heat
18	Choke
19	Brake failure
20	Fuel level
21	Battery charging condition
22	Engine coolant temperature
23	Malfunction indicator light (MI)

x = yes – = no or not separately available o = optional.

d = directly on control, indicator or tell-tale c = in close vicinity.

57.3. Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols which shall be used if they are to be identified

Symbol No	Device	Control / indicator available [^E0022]	Identified by symbol [^E0022]	Where [^E0023]	Tell-tale available [^E0022]	Identified by symbol [^E0022]	Where [^E0023]
1	Parking brake
2	Rear window wiper
3	Rear window washer
4	Rear window wiper and washer
5	Intermittent windscreen wiper
6	Audible warning device
7	Hood
8	Seat belt
9	Engine oil pressure
10	Unleaded petrol
11	…
12	….

x = yes – = no or not separately available o = optional.

d = directly on control, indicator or tell-tale c = in close vicinity.

57.4. Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the interior of the vehicle and showing for tractors without enclosed cab, how the accessibility to internal control devices from the ground has been avoided: …

57.5. Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the exterior of the vehicle and indicating the front and the rear hazard zones in accordance with Appendix 1 of Annex XXIII to Commission Delegated Regulation (EU) No 1322/2014: …

57.6. Requirements under Annexes A and C of standard ISO 15077:2008 (Tractors and self-propelled machinery for agriculture – Operator controls – Actuating forces, displacement, location and method of operation) are met with relevant documentation included in the information document: yes/no (⁴)

57.7. Requirements under paragraph 4.5.3 of standard ISO 4254-1:2013 (Agricultural machinery – Safety – Part 1: General requirements), with the exception of fingertip operation control devices, are met with relevant documentation included in the information document: yes/no (⁴)

57.8. Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs - Quads). Safety requirements and test methods) on throttle control and manual clutch control are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

57.9. For vehicles of T- and C-category, requirements under standard ISO 10975:2009 (Tractors and machinery for agriculture – Auto-guidance systems for operator-controlled tractors and self-propelled machines – Safety requirements) are met with relevant documentation included in the information document: yes/no/not applicable (⁴)

58. PROTECTION AGAINST HAZARDOUS SUBSTANCES

58.1. Brief description (including drawings and photographs) of the air delivery and filtration system, including the devices to obtain a positive differential within the cab and the air flow of fresh filtered air: …

58.2. Requirements under standard EN 15695-1 (Agricultural tractors and self-propelled sprayers — Protection of the operator (driver) against hazardous substances — Part 1: Cab classification, requirements and test procedures): category 1/category 2/category 3 category 4 (⁴) on cab classification with regard to protection against hazardous substances are met with relevant documentation included in the information document: yes/no (⁴)

58.3. Requirements under standard EN 15695-2 (Agricultural tractors and self-propelled sprayers — Protection of the operator (driver) against hazardous substances — Part 2: Filters, requirements and test procedures): Dust filter/Aerosol filter/Vapour filter (⁴) on filters with regard to protection against hazardous substances are met with relevant documentation included in the information document: yes/no (⁴)

59. FOR T- AND C-CATEGORY VEHICLES, MACHINERY (⁶³) MOUNTED ON THE VEHICLE

59.1. General description of the machinery and its inter-action with the vehicle: …

59.2. Overall drawing of the machinery and drawings of the control circuits, as well as the pertinent descriptions and explanations necessary for understanding the operation of the machinery: …

Appendix 1

Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of an engine/engine family system

A. GENERAL INFORMATION

2. GENERAL INFORMATION CONCERNING SYSTEMS, COMPONENTS OR SEPARATE TECHNICAL UNITS

2.1. Make(s) (trade name(s) of manufacturer): …

2.2. Type (⁶): …

2.2.1. Commercial name(s) (if available): …

2.2.2. Type-approval number(s) (⁴⁹) (if available): …

2.2.3. Type-approval(s) issued on (date, if available): …

2.2.4. For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available) (¹⁹): …

2.3. Company name and address of manufacturer: …

2.3.1. Name(s) and address(es) of assembly/manufacture plants: …

2.3.2. Name and address of manufacturer's authorised representative (if any): …

2.4. For systems and separate technical units, vehicle(s) for which they are intended for (²¹):

2.4.1. Type (¹⁷): …

2.4.2. Variant(s) (¹⁷): …

2.4.3. Version(s) (¹⁷): …

2.4.4. Commercial name(s) (if available): …

2.4.5. Category, subcategory and speed index of the vehicle (²): …

5. GENERAL POWERTRAIN CHARACTERISTICS

5.1. Maximum vehicle speed

5.1.1. Forward maximum vehicle speed

5.1.1.1. Declared maximum design vehicle speed: … km/h

5.1.1.2. Calculated maximum design vehicle speed in top gear (show factors used in calculation) (⁴¹): … km/h

5.1.1.3. Measured maximum vehicle speed: … km/h (⁴¹)

5.1.2. Rearward maximum vehicle speed (⁵⁴)

5.1.2.1. Declared rearward maximum design vehicle speed: … km/h

B. INFORMATION ON ENVIRONMENTAL AND PROPULSION PERFORMANCE

6. ESSENTIAL CHARACTERISTICS OF THE ENGINE

6.1.7. Category and sub-category of the engine (⁷):

6.2.1. Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (⁴): …

6.2.2. Ignition Type: Compression ignition/spark ignition (⁴)

6.2.3.1. Cylinders' number: … and configuration (²⁶):

6.2.8. Fuel

6.2.8.1. Fuel Type (⁹):

6.2.8.3. List of additional fuels, fuel mixtures or emulsions compatible with use by the engine declared by the manufacturer in accordance with point 1.4 of Annex I to Delegated Regulation (EU) 2017/654 (provide reference to recognised standard or specification): …

6.3.2.1. Declared rated speed: … rpm

6.3.2.1.2. Declared rated net power: … kW

6.3.2.2. Maximum power speed: … rpm

6.3.2.2.2. Maximum net power: … kW

6.3.6.4. Engine total swept volume: … cm³

Appendix 2

Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an external sound level system

A. GENERAL INFORMATION

2. GENERAL INFORMATION CONCERNING SYSTEMS, COMPONENTS OR SEPARATE TECHNICAL UNITS

2.1. Make(s) (trade name(s) of manufacturer): …

2.2. Type (⁶): …

2.2.1. Commercial name(s) (if available): …

2.2.2. Type-approval number(s) (⁴⁹) (if available): …

2.2.3. Type-approval(s) issued on (date, if available): …

2.2.4. For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available) (¹⁹): …

2.3. Company name and address of manufacturer: …

2.3.1. Name(s) and address(es) of assembly/manufacture plants: …

2.3.2. Name and address of manufacturer's authorised representative (if any): …

2.4. For systems and separate technical units, vehicle(s) for which they are intended for (²¹):

2.4.1. Type (¹⁷): …

2.4.2. Variant(s) (¹⁷): …

2.4.3. Version(s) (¹⁷): …

2.4.4. Commercial name(s) (if available): …

2.4.5. Category, subcategory and speed index of the vehicle (²): …

5. GENERAL POWERTRAIN CHARACTERISTICS

5.1. Maximum vehicle speed

5.1.1. Forward maximum vehicle speed

5.1.1.1. Declared maximum design vehicle speed: … km/h

5.1.1.2. Calculated maximum design vehicle speed in top gear (show factors used in calculation) (⁴¹): … km/h

5.1.1.3. Measured maximum vehicle speed: … km/h (⁴¹)

5.1.2. Rearward maximum vehicle speed (⁵⁴)

5.1.2.1. Declared rearward maximum design vehicle speed: … km/h

6. ESSENTIAL CHARACTERISTICS OF THE ENGINE

6.1.7. Category and sub-category of the engine (⁷):

6.2.1. Combustion Cycle: four stroke cycle/two stroke cycle/rotary/other (specify) (⁴): …

6.2.2. Ignition Type: Compression ignition/spark ignition (⁴)

6.2.3.1. Cylinders' number: … and configuration (²⁶):

6.3.2.1. Declared rated speed: … rpm

6.3.2.1.2. Declared rated net power: … kW

6.3.2.2. Maximum power speed: … rpm

6.3.2.2.2. Maximum net power: … kW

6.3.6.4. Engine total swept volume: … cm³

10. EXTERNAL SOUND LEVEL

10.1. External sound level declared by the manufacturer

10.1.1. Moving: … dB(A)

10.1.2 Stationary: … dB(A)

Reading this document does not replace reading the official text published in the Official Journal of the European Union. We assume no responsibility for any inaccuracies arising from the conversion of the original to this format.

This text is published under EUR-Lex's own terms of reuse, not a Legalize or public-domain licence. EUR-Lex
Creative Commons Attribution 4.0 International (CC BY 4.0)
© European Union, https://eur-lex.europa.eu — Source: EUR-Lex (Publications Office of the European Union). Reused under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Only EU legislation published in the printed Official Journal of the European Union is deemed authentic; consolidated texts are reproduced here for documentation purposes and have been reformatted to Markdown.