LegalizeCommission Implementing Regulation (EU) 2016/1375 of 29 July 2016 amending Council Regulation (EU) No 267/2012 concerning restrictive measures against Iran
This is the act as published. Later amendments are not folded into the text below: each one is a separate act in this repository and an entry in this law's history.
CATEGORY 1 — SPECIAL MATERIALS AND RELATED EQUIPMENT
1A Systems, Equipment and Components
| The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 |
|---|---|---|---|
| 1A007 | b. Electrically driven explosive detonators as follows: 1. Exploding bridge (EB); 2. Exploding bridge wire (EBW); 3. Slapper; 4. Exploding foil initiators (EFI). Technical Notes: 1. The word initiator or igniter is sometimes used in place of the word detonator. 2. For the purpose of 1A007.b. the detonators of concern all utilise a small electrical conductor (bridge, bridge wire, or foil) that explosively vaporises when a fast, high-current electrical pulse is passed through it. In non-slapper types, the exploding conductor starts a chemical detonation in a contacting high explosive material such as PETN (pentaerythritoltetranitrate). In 3. slapper detonators, the explosive vaporization of the electrical conductor drives a flyer or slapper across a gap, and the impact of the slapper on an explosive starts a chemical detonation. The slapper in some designs is driven by magnetic force. The term exploding foil detonator may refer to either an EB or a slapper-type detonator. | 6.A.1. | Detonators and multipoint initiation systems, as follows: a. Electrically driven explosive detonators, as follows: 1. Exploding bridge (EB); 2. Exploding bridge wire (EBW); 3. Slapper; 4. Exploding foil initiators (EFI); |
| 1A007 | Equipment and devices, specially designed to initiate charges and devices containing “energetic materials”, by electrical means, as follows: N.B.: SEE ALSO MILITARY GOODS CONTROLS, 3A229 AND 3A232. a. Explosive detonator firing sets designed to drive explosive detonators specified in 1A007.b.; | 6.A.2. | Firing sets and equivalent high-current pulse generators, as follows: a. Detonator firing sets (initiation systems, firesets), including electronically-charged, explosively-driven and optically-driven firing sets designed to drive multiple controlled detonators specified by Item 6.A.1. above; |
| 1A202 | Composite structures, other than those specified in 1A002, in the form of tubes and having both of the following characteristics: N.B.: SEE ALSO 9A010 AND 9A110. a. An inside diameter of between 75 mm and 400 mm; and b. Made with any of the “fibrous or filamentary materials” specified in 1C010.a. or b. or 1C210.a. or with carbon prepreg materials specified in 1C210.c. | 2.A.3. | Composite structures in the form of tubes having both of the following characteristics: a. An inside diameter of between 75 and 400 mm; and b. Made with any of the “fibrous or filamentary materials” specified in Item 2.C.7.a. or carbon prepreg materials specified in Item 2.C.7.c. |
| 1A225 | Platinized catalysts specially designed or prepared for promoting the hydrogen isotope exchange reaction between hydrogen and water for the recovery of tritium from heavy water or for the production of heavy water. | 2.A.2. | Platinized catalysts specially designed or prepared for promoting the hydrogen isotope exchange reaction between hydrogen and water for the recovery of tritium from heavy water or for the production of heavy water. |
| 1A226 | Specialized packings which may be used in separating heavy water from ordinary water, having both of the following characteristics: a. Made of phosphor bronze mesh chemically treated to improve wettability; and b. Designed to be used in vacuum distillation towers. | 4.A.1. | Specialized packings which may be used in separating heavy water from ordinary water, having both of the following characteristics: a. Made of phosphor bronze mesh chemically treated to improve wettability; and b. Designed to be used in vacuum distillation towers. |
| 1A227 | High-density (lead glass or other) radiation shielding windows, having all of the following characteristics, and specially designed frames therefor: a. A ‘cold area’ greater than 0,09 m2; b. A density greater than 3 g/cm3; and c. A thickness of 100 mm or greater. Technical Note: In 1A227 the term ‘cold area’ means the viewing area of the window exposed to the lowest level of radiation in the design application. | 1.A.1. | High-density (lead glass or other) radiation shielding windows, having all of the following characteristics, and specially designed frames therefor: a. A ‘cold area’ greater than 0,09 m2; b. A density greater than 3 g/cm3; and c. A thickness of 100 mm or greater. Technical Note: In Item 1.A.1.a. the term ‘cold area’ means the viewing area of the window exposed to the lowest level of radiation in the design application. |
1B Test, Inspection and Production Equipment
| The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 |
|---|---|---|---|
| 1B201 | Filament winding machines, other than those specified in 1B001 or 1B101, and related equipment, as follows: a. Filament winding machines having all of the following characteristics: 1. Having motions for positioning, wrapping, and winding fibres coordinated and programmed in two or more axes; 2. Specially designed to fabricate composite structures or laminates from “fibrous or filamentary materials”; and 3. Capable of winding cylindrical tubes with an internal diameter between 75 and 650 mm and lengths of 300 mm or greater; b. Coordinating and programming controls for the filament winding machines specified in 1B201.a.; c. Precision mandrels for the filament winding machines specified in 1B201.a. | 3.B.4. | Filament winding machines and related equipment, as follows: a. Filament winding machines having all of the following characteristics: 1. Having motions for positioning, wrapping, and winding fibers coordinated and programmed in two or more axes; 2. Specially designed to fabricate composite structures or laminates from “fibrous or filamentary materials”; and 3. Capable of winding cylindrical tubes with an internal diameter between 75 and 650 mm and lengths of 300 mm or greater; b. Coordinating and programming controls for the filament winding machines specified in Item 3.B.4.a.; c. Precision mandrels for the filament winding machines specified in Item 3.B.4.a. |
| 1B225 | Electrolytic cells for fluorine production with an output capacity greater than 250 g of fluorine per hour. | 3.B.1. | Electrolytic cells for fluorine production with an output capacity greater than 250 g of fluorine per hour. |
| 1B226 | Electromagnetic isotope separators designed for, or equipped with, single or multiple ion sources capable of providing a total ion beam current of 50 mA or greater. Note: 1B226 includes separators: a. Capable of enriching stable isotopes; b. With the ion sources and collectors both in the magnetic field and those configurations in which they are external to the field. | 3.B.5. | Electromagnetic isotope separators designed for, or equipped with, single or multiple ion sources capable of providing a total ion beam current of 50 mA or greater. Notes: 1. Item 3.B.5. includes separators capable of enriching stable isotopes as well as those for uranium. N.B.: A separator capable of separating the isotopes of lead with a one-mass unit difference is inherently capable of enriching the isotopes of uranium with a three-unit mass difference. 2. Item 3.B.5. includes separators with the ion sources and collectors both in the magnetic field and those configurations in which they are external to the field. Technical Note: A single 50 mA ion source cannot produce more than 3 g of separated highly enriched uranium (HEU) per year from natural abundance feed. |
| 1B228 | Hydrogen-cryogenic distillation columns having all of the following characteristics: a. Designed for operation with internal temperatures of 35 K (–238 °C) or less; b. Designed for operation at an internal pressure of 0,5 to 5 MPa; c. Constructed of either: 1. Stainless steel of the 300 series with low sulphur content and with an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; or 2. Equivalent materials which are both cryogenic and H2-compatible; and d. With internal diameters of 30 cm or greater and ‘effective lengths’ of 4 m or greater. Technical Note: In 1B228 ‘effective length’ means the active height of packing material in a packed-type column, or the active height of internal contactor plates in a plate-type column. | 4.B.2. | Hydrogen-cryogenic distillation columns having all of the following characteristics: a. Designed for operation at internal temperatures of 35 K (–238 °C) or less; b. Designed for operation at internal pressures of 0,5 to 5 MPa; c. Constructed of either: 1. Stainless steel of the 300 series with low sulfur content and with an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; or 2. Equivalent materials which are both cryogenic and H2-compatible; and d. With internal diameters of 30 cm or greater and ‘effective lengths’ of 4 m or greater. Technical Note: The term ‘effective length’ means the active height of packing material in a packed-type column, or the active height of internal contactor plates in a plate-type column. |
| 1B229 | Water-hydrogen sulphide exchange tray columns and ‘internal contactors’, as follows: N.B.: For columns which are specially designed or prepared for the production of heavy water see 0B004. a. Water-hydrogen sulphide exchange tray columns, having all of the following characteristics: 1. Can operate at pressures of 2 MPa or greater; 2. Constructed of carbon steel having an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; and 3. With a diameter of 1,8 m or greater; b. ‘Internal contactors’ for the water-hydrogen sulphide exchange tray columns specified in 1B229.a. Technical Note: ‘Internal contactors’ of the columns are segmented trays which have an effective assembled diameter of 1,8 m or greater, are designed to facilitate countercurrent contacting and are constructed of stainless steels with a carbon content of 0,03 % or less. These may be sieve trays, valve trays, bubble cap trays, or turbogrid trays. | 4.B.1. | Water-hydrogen sulfide exchange tray columns and internal contactors, as follows: N.B.: For columns which are especially designed or prepared for the production of heavy water, see INFCIRC/254/Part 1 (as amended). a. Water-hydrogen sulfide exchange tray columns, having all of the following characteristics: 1. Can operate at pressures of 2 MPa or greater; 2. Constructed of carbon steel having an austenitic ASTM (or equivalent standard) grain size number of 5 or greater; and 3. With a diameter of 1,8 m or greater; b. Internal contactors for the water-hydrogen sulfide exchange tray columns specified in Item 4.B.1.a. Technical Note: Internal contactors of the columns are segmented trays which have an effective assembled diameter of 1,8 m or greater; are designed to facilitate countercurrent contacting and are constructed of stainless steels with a carbon content of 0,03 % or less. These may be sieve trays, valve trays, bubble cap trays or turbogrid trays. |
| 1B230 | Pumps capable of circulating solutions of concentrated or dilute potassium amide catalyst in liquid ammonia (KNH2/NH3), having all of the following characteristics: a. Airtight (i.e., hermetically sealed); b. A capacity greater than 8,5 m3/h; and c. Either of the following characteristics: 1. For concentrated potassium amide solutions (1 % or greater), an operating pressure of 1,5 to 60 MPa; or 2. For dilute potassium amide solutions (less than 1 %), an operating pressure of 20 to 60 MPa. | 4.A.2. | Pumps capable of circulating solutions of concentrated or dilute potassium amide catalyst in liquid ammonia (KNH2/NH3), having all of the following characteristics: a. Airtight (i.e., hermetically sealed); b. A capacity greater than 8,5 m3/h; and c. Either of the following characteristics: 1. For concentrated potassium amide solutions (1 % or greater), an operating pressure of 1,5 to 60 MPa; or 2. For dilute potassium amide solutions (less than 1 %), an operating pressure of 20 to 60 MPa. |
| 1B231 | Tritium facilities or plants, and equipment therefor, as follows: a. Facilities or plants for the production, recovery, extraction, concentration, or handling of tritium; b. Equipment for tritium facilities or plants, as follows: 1. Hydrogen or helium refrigeration units capable of cooling to 23 K (–250 °C) or less, with heat removal capacity greater than 150 W; 2. Hydrogen isotope storage or purification systems using metal hydrides as the storage or purification medium. | 2.B.1. | Tritium facilities or plants, and equipment therefor, as follows: a. Facilities or plants for the production, recovery, extraction, concentration or handling of tritium; b. Equipment for tritium facilities or plants, as follows: 1. Hydrogen or helium refrigeration units capable of cooling to 23 K (–250 °C) or less, with heat removal capacity greater than 150 W; 2. Hydrogen isotope storage or purification systems using metal hydrides as the storage or purification medium. |
| 1B232 | Turboexpanders or turboexpander-compressor sets having both of the following characteristics: a. Designed for operation with an outlet temperature of 35 K (–238 °C) or less; and b. Designed for a throughput of hydrogen gas of 1 000 kg/h or greater. | 4.A.3. | Turboexpanders or turboexpander-compressor sets having both of the following characteristics: a. Designed for operation with an outlet temperature of 35 K (– 238 °C) or less; and b. Designed for a throughput of hydrogen gas of 1 000 kg/h or greater. |
| 1B233 | Lithium isotope separation facilities or plants, and systems and equipment therefor, as follows: a. Facilities or plants for the separation of lithium isotopes; b. Equipment for the separation of lithium isotopes based on the lithium-mercury amalgam process, as follows: 1. Packed liquid-liquid exchange columns specially designed for lithium amalgams; 2. Mercury or lithium amalgam pumps; 3. Lithium amalgam electrolysis cells; 4. Evaporators for concentrated lithium hydroxide solution; c. Ion exchange systems specially designed for lithium isotope separation, and specially designed components therefor; d. Chemical exchange systems (employing crown ethers, cryptands, or lariat ethers), specially designed for lithium isotope separation, and specially designed components therefor. | 2.B.2. | Lithium isotope separation facilities or plants, and systems and equipment therefor, as follows: N.B.: Certain lithium isotope separation equipment and components for the plasma separation process (PSP) are also directly applicable to uranium isotope separation and are controlled under INFCIRC/254 Part 1 (as amended). a. Facilities or plants for the separation of lithium isotopes; b. Equipment for the separation of lithium isotopes based on the lithium-mercury amalgam process, as follows: 1. Packed liquid-liquid exchange columns specially designed for lithium amalgams; 2. Mercury or lithium amalgam pumps; 3. Lithium amalgam electrolysis cells; 4. Evaporators for concentrated lithium hydroxide solution; c. Ion exchange systems specially designed for lithium isotope separation, and specially designed component parts therefor; d. Chemical exchange systems (employing crown ethers, cryptands, or lariat ethers) specially designed for lithium isotope separation, and specially designed component parts therefor. |
| 1B234 | High explosive containment vessels, chambers, containers and other similar containment devices designed for the testing of high explosives or explosive devices and having both of the following characteristics: N.B.: SEE ALSO MILITARY GOODS CONTROLS. a. Designed to fully contain an explosion equivalent to 2 kg of TNT or greater; and b. Having design elements or features enabling real time or delayed transfer of diagnostic or measurement information. | 5.B.7. | High explosive containment vessels, chambers, containers and other similar containment devices designed for the testing of high explosives or explosive devices and having both of the following characteristics: a. Designed to fully contain an explosion equivalent to 2 kg of TNT or greater; and b. Having design elements or features enabling real time or delayed transfer of diagnostic or measurement information. |
1C Materials
| The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 |
|---|---|---|---|
| 1C202 | Alloys, other than those specified in 1C002.b.3. or .b.4., as follows: a. Aluminium alloys having both of the following characteristics: 1. ‘Capable of’ an ultimate tensile strength of 460 MPa or more at 293 K (20 °C); and 2. In the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm; | 2.C.1. | Aluminium alloys having both of the following characteristics: a. ‘Capable of’ an ultimate tensile strength of 460 MPa or more at 293 K (20 °C); b. and b. In the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm Technical Note: In Item 2.C.1. the phrase ‘capable of’ encompasses aluminium alloys before or after heat treatment. |
| 1C202 | b. Titanium alloys having both of the following characteristics: 1. ‘Capable of’ an ultimate tensile strength of 900 MPa or more at 293 K (20 °C); and 2. In the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm. Technical Note: The phrase alloys ‘capable of’ encompasses alloys before or after heat treatment. | 2.C.13. | Titanium alloys having both of the following characteristics: a. ‘Capable of’ an ultimate tensile strength of 900 MPa or more at 293 K (20 °C); In the form of tubes or cylindrical solid forms (including forgings) with an outside diameter of more than 75 mm. Technical Note: In Item 2.C.13. the phrase ‘capable of’ encompasses titanium alloys before or after heat treatment |
| 1C210 | ‘Fibrous or filamentary materials’ or prepregs, other than those specified in 1C010.a., b. or e., as follows: a. Carbon or aramid ‘fibrous or filamentary materials’ having either of the following characteristics: 1. A “specific modulus” of 12,7 × 106 m or greater; or 2. A “specific tensile strength” of 23,5 × 104 m or greater; Note: 1C210.a. does not control aramid ‘fibrous or filamentary materials’ having 0,25 % by weight or more of an ester based fibre surface modifier; | 2.C.7.a | “Fibrous or filamentary materials”, and prepregs, as follows: a. Carbon or aramid “fibrous or filamentary materials” having either of the following characteristics: 1. A “specific modulus” of 12,7 × 106 m or greater; or 2. A “specific tensile strength” of 23,5 × 104 m or greater; Note: Item 2.C.7.a. does not control aramid “fibrous or filamentary materials” having 0,25 % or more by weight of an ester based fiber surface modifier. |
| 1C210 | b. Glass ‘fibrous or filamentary materials’ having both of the following characteristics: 1. A “specific modulus” of 3,18 × 106 m or greater; and 2. A “specific tensile strength” of 7,62 × 104 m or greater; | 2.C.7.b | Glass “fibrous or filamentary materials” having both of the following characteristics: 1. A “specific modulus” of 3,18 × 106 m or greater; and 2. A “specific tensile strength” of 7,62 × 104 m or greater; |
| 1C210 | c. Thermoset resin impregnated continuous “yarns”, “rovings”, “tows” or “tapes” with a width of 15 mm or less (prepregs), made from carbon or glass ‘fibrous or filamentary materials’ specified in 1C210.a. or b. Technical Note: The resin forms the matrix of the composite. Note: In 1C210, ‘fibrous or filamentary materials’ is restricted to continuous “monofilaments”, “yarns”, “rovings”, “tows” or “tapes”. | 2.C.7.c | c. Thermoset resin impregnated continuous “yarns”, “rovings”, “tows” or “tapes” with a width of 15 mm or less (prepregs), made from carbon or glass “fibrous or filamentary materials” specified in Item 2.C.7.a. or Item 2.C.7.b. Technical Note: The resin forms the matrix of the composite. Technical Notes: 1. In Item 2.C.7. “Specific modulus” is the Young's modulus in N/m2 divided by the specific weight in N/m3 when measured at a temperature of 296 ± 2 K (23 ± 2 °C) and a relative humidity of 50 ± 5 %. 2. In Item 2.C.7. “Specific tensile strength” is the ultimate tensile strength in N/m2 divided by the specific weight in N/m3 when measured at a temperature of 296 ± 2 K (23 ± 2 °C) and a relative humidity of 50 ± 5 %. |
| 1C216 | Maraging steel, other than that specified in 1C116, ‘capable of’ an ultimate tensile strength of 1 950 MPa or more, at 293 K (20 °C). Note: 1C216 does not control forms in which all linear dimensions are 75 mm or less. Technical Note: The phrase maraging steel ‘capable of’ encompasses maraging steel before or after heat treatment. | 2.C.11. | Maraging steel ‘capable of’ an ultimate tensile strength of 1 950 MPa or more at 293 K (20 °C). Note: Item 2.C.11. does not control forms in which all linear dimensions are 75 mm or less. Technical Note: In Item 2.C.11. the phrase ‘capable of’ encompasses maraging steel before or after heat treatment. |
| 1C225 | Boron enriched in the boron-10 (10B) isotope to greater than its natural isotopic abundance, as follows: elemental boron, compounds, mixtures containing boron, manufactures thereof, waste or scrap of any of the foregoing. Note: In 1C225 mixtures containing boron include boron loaded materials. Technical Note: The natural isotopic abundance of boron-10 is approximately 18,5 weight per cent (20 atom per cent). | 2.C.4. | Boron enriched in the boron-10 (10B) isotope to greater than its natural isotopic abundance, as follows: elemental boron, compounds, mixtures containing boron, manufactures thereof, waste or scrap of any of the foregoing. Note: In Item 2.C.4. mixtures containing boron include boron loaded materials. Technical Note: The natural isotopic abundance of boron-10 is approximately 18,5 weight percent (20 atom percent). |
| 1C226 | Tungsten, tungsten carbide, and alloys containing more than 90 % tungsten by weight, other than that specified by 1C117, having both of the following characteristics: a. In forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 mm and 300 mm; and b. A mass greater than 20 kg. Note: 1C226 does not control manufactures specially designed as weights or gamma-ray collimators. | 2.C.14. | Tungsten, tungsten carbide, and alloys containing more than 90 % tungsten by weight, having both of the following characteristics: a. In forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 and 300 mm; and b. A mass greater than 20 kg. Note: Item 2.C.14. does not control manufactures specially designed as weights or gamma-ray collimators. |
| 1C227 | Calcium having both of the following characteristics: a. Containing less than 1 000 parts per million by weight of metallic impurities other than magnesium; and b. Containing less than 10 parts per million by weight of boron. | 2.C.5. | Calcium having both of the following characteristics: a. Containing less than 1 000 parts per million by weight of metallic impurities other than magnesium; and b. Containing less than 10 parts per million by weight of boron. |
| 1C228 | Magnesium having both of the following characteristics: a. Containing less than 200 parts per million by weight of metallic impurities other than calcium; and b. Containing less than 10 parts per million by weight of boron. | 2.C.10. | Magnesium having both of the following characteristics: a. Containing less than 200 parts per million by weight of metallic impurities other than calcium; and b. Containing less than 10 parts per million by weight of boron. |
| 1C229 | Bismuth having both of the following characteristics: a. A purity of 99,99 % or greater by weight; and b. Containing less than 10 ppm (parts per million) by weight of silver. | 2.C.3. | Bismuth having both of the following characteristics: a. A purity of 99,99 % or greater by weight; and b. Containing less than 10 ppm (parts per million) by weight of silver. |
| 1C230 | Beryllium metal, alloys containing more than 50 % beryllium by weight, beryllium compounds, manufactures thereof, and waste or scrap of any of the foregoing, other than that specified in the Military Goods Controls. N.B.: SEE ALSO MILITARY GOODS CONTROLS. Note: 1C230 does not control the following: a. Metal windows for X-ray machines, or for bore-hole logging devices; b. Oxide shapes in fabricated or semi-fabricated forms specially designed for electronic component parts or as substrates for electronic circuits; c. Beryl (silicate of beryllium and aluminium) in the form of emeralds or aquamarines. | 2.C.2. | Beryllium metal, alloys containing more than 50 % beryllium by weight, beryllium compounds, manufactures thereof, and waste or scrap of any of the foregoing. Note: Item 2.C.2. does not control the following: a. Metal windows for X-ray machines or for bore-hole logging devices; b. Oxide shapes in fabricated or semi-fabricated forms specially designed for electronic component parts or as substrates for electronic circuits; c. Beryl (silicate of beryllium and aluminium) in the form of emeralds or aquamarines. |
| 1C231 | Hafnium metal, alloys containing more than 60 % hafnium by weight, hafnium compounds containing more than 60 % hafnium by weight, manufactures thereof, and waste or scrap of any of the foregoing. | 2.C.8. | Hafnium metal, alloys containing more than 60 % hafnium by weight, hafnium compounds containing more than 60 % hafnium by weight, manufactures thereof, and waste or scrap of any of the foregoing. |
| 1C232 | Helium-3 (3He), mixtures containing helium-3, and products or devices containing any of the foregoing. Note: 1C232 does not control a product or device containing less than 1 g of helium-3. | 2.C.18. | Helium-3 (3He), mixtures containing helium-3, and products or devices containing any of the foregoing. Note: Item 2.C.18. does not control a product or device containing less than 1 g of helium-3. |
| 1C233 | Lithium enriched in the lithium-6 (6Li) isotope to greater than its natural isotopic abundance, and products or devices containing enriched lithium, as follows: elemental lithium, alloys, compounds, mixtures containing lithium, manufactures thereof, waste or scrap of any of the foregoing. Note: 1C233 does not control thermoluminescent dosimeters. Technical Note: The natural isotopic abundance of lithium-6 is approximately 6,5 weight per cent (7,5 atom per cent). | 2.C.9. | Lithium enriched in the lithium-6 (6Li) isotope to greater than its natural isotopic abundance and products or devices containing enriched lithium, as follows: elemental lithium, alloys, compounds, mixtures containing lithium, manufactures thereof, waste or scrap of any of the foregoing. Note: Item 2.C.9. does not control thermoluminescent dosimeters. Technical Note: The natural isotopic abundance of lithium-6 is approximately 6,5 weight percent (7,5 atom percent). |
| 1C234 | Zirconium with a hafnium content of less than 1 part hafnium to 500 parts zirconium by weight, as follows: metal, alloys containing more than 50 % zirconium by weight, compounds, manufactures thereof, waste or scrap of any of the foregoing, other than those specified in 0A001.f. Note: 1C234 does not control zirconium in the form of foil having a thickness of 0,10 mm or less. | 2.C.15. | Zirconium with a hafnium content of less than 1 part hafnium to 500 parts zirconium by weight, as follows: metal, alloys containing more than 50 % zirconium by weight, compounds, manufactures thereof, waste or scrap of any of the foregoing. Note: Item 2.C.15. does not control zirconium in the form of foil having a thickness of 0,10 mm or less. |
| 1C235 | Tritium, tritium compounds, mixtures containing tritium in which the ratio of tritium to hydrogen atoms exceeds 1 part in 1 000 , and products or devices containing any of the foregoing. Note: 1C235 does not control a product or device containing less than 1,48 × 103 GBq (40 Ci) of tritium. | 2.C.17. | Tritium, tritium compounds, mixtures containing tritium in which the ratio of tritium to hydrogen atoms exceeds 1 part in 1 000 , and products or devices containing any of the foregoing. Note: Item 2.C.17. does not control a product or device containing less than 1,48 × 103 GBq of tritium. |
| 1C236 | ‘Radionuclides’ appropriate for making neutron sources based on alpha-n reaction, other than those specified in 0C001 and 1C012.a., in the following forms: a. Elemental; b. Compounds having a total activity of 37 GBq/kg (1 Ci/kg) or greater; c. Mixtures having a total activity of 37 GBq/kg (1 Ci/kg) or greater; d. Products or devices containing any of the foregoing. Note: 1C236 does not control a product or device containing less than 3,7 GBq (100 millicuries) of activity. Technical Note: In 1C236 ‘radionuclides’ are any of the following: — Actinium-225 (Ac-225) — Actinium-227 (Ac-227) — Californium-253 (Cf-253) — Curium-240 (Cm-240) — Curium-241 (Cm-241) — Curium-242 (Cm-242) — Curium-243 (Cm-243) — Curium-244 (Cm-244) — Einsteinium-253 (Es-253) — Einsteinium-254 (Es-254) — Gadolinium-148 (Gd-148) — Plutonium-236 (Pu-236) — Plutonium-238 (Pu-238) — Polonium-208 (Po-208) — Polonium-209 (Po-209) — Polonium-210 (Po-210) — Radium-223 (Ra-223) — Thorium-227 (Th-227) — Thorium-228 (Th-228) — Uranium-230 (U-230) — Uranium-232 (U-232) | 2.C.19. | Radionuclides appropriate for making neutron sources based on alpha-n reaction: Actinium 225 Curium 244 Polonium 209 Actinium 227 Einsteinium 253 Polonium 210 Californium 253 Einsteinium 254 Radium 223 Curium 240 Gadolinium 148 Thorium 227 Curium 241 Plutonium 236 Thorium 228 Curium 242 Plutonium 238 Uranium 230 Curium 243 Polonium 208 Uranium 232 In the following forms: a. Elemental; b. Compounds having a total activity of 37 GBq per kg or greater; c. Mixtures having a total activity of 37 GBq per kg or greater; d. Products or devices containing any of the foregoing. Note: Item 2.C.19. does not control a product or device containing less than 3,7 GBq of activity. |
| 1C237 | Radium 226 (226Ra), radium-226 alloys, radium-226 compounds, mixtures containing radium 226, manufactures thereof, and products or devices containing any of the foregoing. Note: 1C237 does not control the following: a. Medical applicators; b. A product or device containing less than 0,37 GBq (10 millicuries) of radium 226. | 2.C.12. | Radium-226 (226Ra), radium-226 alloys, radium-226 compounds, mixtures containing radium-226, manufactures thereof, and products or devices containing any of the foregoing. Note: Item 2.C.12. does not control the following: a. Medical applicators; b. A product or device containing less than 0,37 GBq of radium-226. |
| 1C238 | Chlorine trifluoride (ClF3). | 2.C.6. | Chlorine trifluoride (ClF3). |
| 1C239 | High explosives, other than those specified in the Military Goods Controls, or substances or mixtures containing more than 2 % by weight thereof, with a crystal density greater than 1,8 g/cm3 and having a detonation velocity greater than 8 000 m/s. | 6.C.1.o | Any explosive with a crystal density greater than 1,8 g/cm3 and having a detonation velocity greater than 8 000 m/s. |
| 1C240 | Nickel powder and porous nickel metal, other than those specified in 0C005, as follows: a. Nickel powder having both of the following characteristics: 1. A nickel purity content of 99,0 % or greater by weight; and 2. A mean particle size of less than 10 μm measured by American Society for Testing and Materials (ASTM) B330 standard; b. Porous nickel metal produced from materials specified in 1C240.a. Note: 1C240 does not control the following: a. Filamentary nickel powders; b. Single porous nickel sheets with an area of 1 000 cm2 per sheet or less. Technical Note: 1C240.b. refers to porous metal formed by compacting and sintering the materials in 1C240.a. to form a metal material with fine pores interconnected throughout the structure. | 2.C.16. | Nickel powder and porous nickel metal, as follows: N.B.: For nickel powders which are especially prepared for the manufacture of gaseous diffusion barriers see INFCIRC/254/Part 1 (as amended). a. Nickel powder having both of the following characteristics: 1. A nickel purity content of 99,0 % or greater by weight; and 2. A mean particle size of less than 10 μm measured by the ASTM B 330 standard; b. Porous nickel metal produced from materials specified in Item 2.C.16.a. Note: Item 2.C.16. does not control the following: a. Filamentary nickel powders; b. Single porous nickel metal sheets with an area of 1 000 cm2 per sheet or less. Technical Note: Item 2.C.16.b. refers to porous metal formed by compacting and sintering the material in Item 2.C.16.a. to form a metal material with fine pores interconnected throughout the structure. |
| 1C241 | Rhenium, and alloys containing 90 % by weight or more rhenium; and alloys of rhenium and tungsten containing 90 % by weight or more of any combination of rhenium and tungsten, other than those specified in 1C226, having both of the following characteristics: a. In forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 and 300 mm; and b. A mass greater than 20 kg. | 2.C.20. | Rhenium, and alloys containing 90 % by weight or more rhenium; and alloys of rhenium and tungsten containing 90 % by weight or more of any combination of rhenium and tungsten, having both of the following characteristics: a. In forms with a hollow cylindrical symmetry (including cylinder segments) with an inside diameter between 100 and 300 mm; and b. A mass greater than 20 kg. |
1D Software
| The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 |
|---|---|---|---|
| 1D001 | “Software” specially designed or modified for the “development”, “production” or “use” of equipment specified in 1B001 to 1B003. | 1.D.2. | “software” means a collection of one or more “programs” or “microprograms” fixed in any tangible medium of expression |
| 1D201 | “Software” specially designed for the “use” of goods specified in 1B201. | 1.D.3. | “software” means a collection of one or more “programs” or “microprograms” fixed in any tangible medium of expression |
1E Technology
| The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 |
|---|---|---|---|
| 1E201 | “Technology” according to the General Technology Note for the “use” of goods specified in 1A002, 1A007, 1A202, 1A225 to 1A227, 1B201, 1B225 to 1B234, 1C002.b.3. or .b.4., 1C010.b., 1C202, 1C210, 1C216, 1C225 to 1C241 or 1D201. | 1.E.1. | “Technology” -- means specific information required for the “development”, “production”, or “use” of any item contained in the List. This information may take the form of “technical data” or “technical assistance”. |
| 1E202 | “Technology” according to the General Technology Note for the “development” or “production” of goods specified in 1A007, 1A202 or 1A225 to 1A227. | 1.E.1. | “Technology” -- means specific information required for the “development”, “production”, or “use” of any item contained in the List. This information may take the form of “technical data” or “technical assistance”. |
| 1E203 | “Technology” according to the General Technology Note for the “development” or “production” of goods specified in 1A007, 1A202 or 1A225 to 1A227. | 1.E.1. | “Technology” -- means specific information required for the “development”, “production”, or “use” of any item contained in the List. This information may take the form of “technical data” or “technical assistance”. |
CATEGORY 2 — MATERIALS PROCESSING
2A Systems, Equipment and Components
| The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 | Nuclear Suppliers Group's control list as in INFCIRC/254/Rev.9/Part 2 |
|---|---|---|---|
| 2A225 | Crucibles made of materials resistant to liquid actinide metals, as follows: a. Crucibles having both of the following characteristics: 1. A volume of between 150 cm3 and 8 000 cm3; and 2. Made of or coated with any of the following materials, or combination of the following materials, having an overall impurity level of 2 % or less by weight: a. Calcium fluoride (CaF2); b. Calcium zirconate (metazirconate) (CaZrO3); c. Cerium sulphide (Ce2S3); d. Erbium oxide (erbia) (Er2O3); e. Hafnium oxide (hafnia) (HfO2); f. Magnesium oxide (MgO); g. Nitrided niobium-titanium-tungsten alloy (approximately 50 % Nb, 30 % Ti, 20 % W); h. Yttrium oxide (yttria) (Y2O3); or i. Zirconium oxide (zirconia) (ZrO2); b. Crucibles having both of the following characteristics: 1. A volume of between 50 cm3 and 2 000 cm3; and 2. Made of or lined with tantalum, having a purity of 99,9 % or greater by weight; c. Crucibles having all of the following characteristics: 1. A volume of between 50 cm3 and 2 000 cm3; 2. Made of or lined with tantalum, having a purity of 98 % or greater by weight; and 3. Coated with tantalum carbide, nitride, boride, or any combination thereof. | 2.A.1 | Crucibles made of materials resistant to liquid actinide metals, as follows: a. Crucibles having both of the following characteristics: 1. A volume of between 150 cm3 (150 ml) and 8 000 cm3 (8 l (litres)); and 2. Made of or coated with any of the following materials, or combination of the following materials, having an overall impurity level of 2 % or less by weight: a. Calcium fluoride (CaF2); b. Calcium zirconate (metazirconate) (CaZrO3); c. Cerium sulfide (Ce2S3); d. Erbium oxide (erbia) (Er2O3); e. Hafnium oxide (hafnia) (HfO2); f. Magnesium oxide (MgO); g. Nitrided niobium-titanium-tungsten alloy (approximately 50 % Nb, 30 % Ti, 20 % W); h. Yttrium oxide (yttria) (Y2O3); or i. Zirconium oxide (zirconia) (ZrO2); b. Crucibles having both of the following characteristics: 1. A volume of between 50 cm3 (50 ml) and 2 000 cm3 (2 liters); and 2. Made of or lined with tantalum, having a purity of 99,9 % or greater by weight; c. Crucibles having all of the following characteristics: 1. A volume of between 50 cm3 (50 ml) and 2 000 cm3 (2 liters); 2. Made of or lined with tantalum, having a purity of 98 % or greater by weight; and 3. Coated with tantalum carbide, nitride, boride, or any combination thereof. |
| 2A226 | Valves having all of the following characteristics: a. A ‘nominal size’ of 5 mm or greater; b. Having a bellows seal; and c. Wholly made of or lined with aluminium, aluminium alloy, nickel, or nickel alloy containing more than 60 % nickel by weight. Technical Note: For valves with different inlet and outlet diameters, the ‘nominal size’ in 2A226 refers to the smallest diameter. | 3.A.3. | Valves having all of the following characteristics: a. A nominal size of 5 mm or greater; b. Having a bellows seal; and c. Wholly made of or lined with aluminium, aluminium alloy, nickel, or nickel alloy containing more than 60 % nickel by weight. Technical Note: For valves with different inlet and outlet diameter, the nominal size parameter in Item 3.A.3.a. refers to the smallest diameter. |
2B Test, Inspection and Production Equipment
Reading this document does not replace reading the official text published in the Official Journal of the European Union. We assume no responsibility for any inaccuracies arising from the conversion of the original to this format.
This text is published under EUR-Lex's own terms of reuse, not a Legalize or public-domain licence.
EUR-Lex
Creative Commons Attribution 4.0 International (CC BY 4.0)
© European Union, https://eur-lex.europa.eu — Source: EUR-Lex (Publications Office of the European Union). Reused under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Only EU legislation published in the printed Official Journal of the European Union is deemed authentic; consolidated texts are reproduced here for documentation purposes and have been reformatted to Markdown.