Legalize / European Union / Implementing Regulation

Commission Implementing Regulation (EU) 2016/1375 of 29 July 2016 amending Council Regulation (EU) No 267/2012 concerning restrictive measures against Iran

Type Implementing Regulation

Publication 2016-08-16

State In force

Text As published

Department European Commission

Source EUR-Lex

articles 2

This is the act as published. Later amendments are not folded into the text below: each one is a separate act in this repository and an entry in this law's history.

Reform history JSON API

The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex
1B001	Equipment for the production or inspection of “composite” structures or laminates specified in 1A002 or “fibrous or filamentary materials” specified in 1C010, as follows, and specially designed components and accessories therefor: N.B.: SEE ALSO 1B101 AND 1B201.
1B001	a. Filament winding machines, of which the motions for positioning, wrapping and winding fibres are coordinated and programmed in three or more ‘primary servo positioning’ axes, specially designed for the manufacture of “composite” structures or laminates, from “fibrous or filamentary materials”;	M6B1a	Filament winding machines or ‘fibre/tow-placement machines’, of which the motions for positioning, wrapping and winding fibres can be coordinated and programmed in three or more axes, designed to fabricate composite structures or laminates from fibrous or filamentary materials, and co-ordinating and programming controls
1B001	b. ‘Tape-laying machines’, of which the motions for positioning and laying tape are coordinated and programmed in five or more ‘primary servo positioning’ axes, specially designed for the manufacture of “composite” airframe or ‘missile’ structures; Note: In 1B001.b., ‘missile’ means complete rocket systems and unmanned aerial vehicle systems. Technical Note: For the purposes of 1B001.b., ‘tape-laying machines’ have the ability to lay one or more ‘filament bands’ limited to widths greater than 25 mm and less than or equal to 305 mm, and to cut and restart individual ‘filament band’ courses during the laying process.	M6B1b	‘Tape-laying machines’ of which the motions for positioning and laying tape can be co-ordinated and programmed in two or more axes, designed for the manufacture of composite airframes and missile structures; Note: For the purposes of 6.B.1.a. and 6.B.1.b., the following definitions apply: 1. A ‘filament band’ is a single continuous width of fully or partially resinimpregnated tape, tow, or fibre. Fully or partially resin-impregnated ‘filament bands’ include those coated with dry powder that tacks upon heating. 2. ‘Fibre/tow-placement machines’ and ‘tape-laying machines’ are machines that perform similar processes that use computer-guided heads to lay one or several ‘filament bands’ onto a mold to create a part or a structure. These machines have the ability to cut and restart individual ‘filament band’ courses during the laying process. 3. ‘Fibre/tow-placement machines’ have the ability to place one or more ‘filament bands’ having widths less than or equal to 25,4 mm. This refers to the minimum width of material the machine can place, regardless of the upper capability of the machine. 4. ‘Tape-laying machines’ have the ability to place one or more ‘filament bands’ having widths less than or equal to 304,8 mm, but cannot place ‘filaments bands’ with a width equal to or less than 25,4 mm. This refers to the minimum width of material the machine can place, regardless of the upper capability of the machine.
1B001	c. Multidirectional, multidimensional weaving machines or interlacing machines, including adapters and modification kits, specially designed or modified for weaving, interlacing or braiding fibres, for “composite” structures; Technical Note: For the purposes of 1B001.c., the technique of interlacing includes knitting.	M6B1c	Multi-directional, multi-dimensional weaving machines or interlacing machines, including adapters and modification kits for weaving, interlacing or braiding fibres to manufacture composite structures; Note: 6.B.1.c. does not control textile machinery not modified for the end-uses stated.
1B001	d. Equipment specially designed or adapted for the production of reinforcement fibres, as follows:		Equipment designed or modified for the production of fibrous or filamentary materials as follows:
1B001	1. Equipment for converting polymeric fibres (such as polyacrylonitrile, rayon, pitch or polycarbosilane) into carbon fibres or silicon carbide fibres, including special equipment to strain the fibre during heating;	M6B1d1	1. Equipment for converting polymeric fibres (such as polyacrylonitrile, rayon, or polycarbosilane) including special provision to strain the fibre during heating;
1B001	2. Equipment for the chemical vapour deposition of elements or compounds, on heated filamentary substrates, to manufacture silicon carbide fibres;	M6B1d2	2. Equipment for the vapour deposition of elements or compounds on heated filament substrates;
1B001	3. Equipment for the wet-spinning of refractory ceramics (such as aluminium oxide);	M6B1d3	3. Equipment for the wet-spinning of refractory ceramics (such as aluminium oxide)
1B001	4. Equipment for converting aluminium containing precursor fibres into alumina fibres by heat treatment; e. Equipment for producing prepregs specified in 1C010.e. by the hot melt method; f. Non-destructive inspection equipment specially designed for “composite” materials, as follows: 1. X-ray tomography systems for three dimensional defect inspection; 2. Numerically controlled ultrasonic testing machines of which the motions for positioning transmitters or receivers are simultaneously coordinated and programmed in four or more axes to follow the three dimensional contours of the component under inspection; g. ‘Tow-placement machines’, of which the motions for positioning and laying tows are coordinated and programmed in two or more ‘primary servo positioning’ axes, specially designed for the manufacture of “composite” airframe or ‘missile’ structures. Technical Note: For the purposes of 1B001.g., ‘tow-placement machines’ have the ability to place one or more ‘filament bands’ having widths less than or equal to 25 mm, and to cut and restart individual ‘filament band’ courses during the placement process. Technical Note: 1. For the purpose of 1B001, ‘primary servo positioning’ axes control, under computer program direction, the position of the end effector (i.e., head) in space relative to the work piece at the correct orientation and direction to achieve the desired process. 2. For the purposes of 1B001., a ‘filament band’ is a single continuous width of fully or partially resin-impregnated tape, tow or fibre.	M6B1e	Equipment designed or modified for special fibre surface treatment or for producing prepregs and preforms, including rollers, tension stretchers, coating equipment, cutting equipment and clicker dies. Note: Examples of components and accessories for the machines specified in 6.B.1. are moulds, mandrels, dies, fixtures and tooling for the preform pressing, curing, casting, sintering or bonding of composite structures, laminates and manufactures thereof
1B002	Equipment for producing metal alloys, metal alloy powder or alloyed materials, specially designed to avoid contamination and specially designed for use in one of the processes specified in 1C002.c.2. N.B.: SEE ALSO 1B102.	M4B3d	Metal powder “production equipment” usable for the “production”, in a controlled environment, of spherical, spheroidal or atomised materials specified in 4.C.2.c., 4.C.2.d. or 4.C.2.e. Note: 4.B.3.d. includes: a. Plasma generators (high frequency arc-jet) usable for obtaining sputtered or spherical metallic powders with organization of the process in an argon-water environment; b. Electroburst equipment usable for obtaining sputtered or spherical metallic powders with organization of the process in an argon-water environment; c. Equipment usable for the “production” of spherical aluminium powders by powdering a melt in an inert medium (e.g. nitrogen). Notes: 1. The only batch mixers, continuous mixers, usable for solid propellants or propellants constituents specified in 4.C., and fluid energy mills specified in 4.B., are those specified in 4.B.3. 2. Forms of metal powder “production equipment” not specified in 4.B.3.d. are to be evaluated in accordance with 4.B.2.
1B101	Equipment, other than that specified in 1B001, for the “production” of structural composites as follows; and specially designed components and accessories therefor: N.B.: SEE ALSO 1B201. Note: Components and accessories specified in 1B101 include moulds, mandrels, dies, fixtures and tooling for the preform pressing, curing, casting, sintering or bonding of composite structures, laminates and manufactures thereof.
1B101	a. Filament winding machines or fibre placement machines, of which the motions for positioning, wrapping and winding fibres can be coordinated and programmed in three or more axes, designed to fabricate composite structures or laminates from fibrous or filamentary materials, and coordinating and programming controls;	M6B1a	Filament winding machines or ‘fibre/tow-placement machines’, of which the motions for positioning, wrapping and winding fibres can be coordinated and programmed in three or more axes, designed to fabricate composite structures or laminates from fibrous or filamentary materials, and co-ordinating and programming controls;
1B101	b. Tape-laying machines of which the motions for positioning and laying tape and sheets can be coordinated and programmed in two or more axes, designed for the manufacture of composite airframe and “missile” structures;	M6B1b	‘Tape-laying machines’ of which the motions for positioning and laying tape can be co-ordinated and programmed in two or more axes, designed for the manufacture of composite airframes and missile structures; Note: For the purposes of 6.B.1.a. and 6.B.1.b., the following definitions apply: 1. A ‘filament band’ is a single continuous width of fully or partially resinimpregnated tape, tow, or fibre. Fully or partially resin-impregnated ‘filament bands’ include those coated with dry powder that tacks upon heating. 2. ‘Fibre/tow-placement machines’ and ‘tape-laying machines’ are machines that perform similar processes that use computer-guided heads to lay one or several ‘filament bands’ onto a mold to create a part or a structure. These machines have the ability to cut and restart individual ‘filament band’ courses during the laying process. 3. ‘Fibre/tow-placement machines’ have the ability to place one or more ‘filament bands’ having widths less than or equal to 25,4 mm. This refers to the minimum width of material the machine can place, regardless of the upper capability of the machine. 4. ‘Tape-laying machines’ have the ability to place one or more ‘filament bands’ having widths less than or equal to 304,8 mm, but cannot place ‘filaments bands’ with a width equal to or less than 25,4 mm. This refers to the minimum width of material the machine can place, regardless of the upper capability of the machine.
1B101	c. Equipment designed or modified for the “production” of “fibrous or filamentary materials” as follows: 1. Equipment for converting polymeric fibres (such as polyacrylonitrile, rayon or polycarbosilane) including special provision to strain the fibre during heating; 2. Equipment for the vapour deposition of elements or compounds on heated filament substrates; 3. Equipment for the wet-spinning of refractory ceramics (such as aluminium oxide);	M6B1d	Equipment designed or modified for the production of fibrous or filamentary materials as follows: 1. Equipment for converting polymeric fibres (such as polyacrylonitrile, rayon, or polycarbosilane) including special provision to strain the fibre during heating; 2. Equipment for the vapour deposition of elements or compounds on heated filament substrates; 3. Equipment for the wet-spinning of refractory ceramics (such as aluminium oxide);
1B101	d. Equipment designed or modified for special fibre surface treatment or for producing prepregs and preforms specified in entry 9C110. Note: 1B101.d. includes rollers, tension stretchers, coating equipment, cutting equipment and clicker dies.	M6B1e	Equipment designed or modified for special fibre surface treatment or for producing prepregs and preforms, including rollers, tension stretchers, coating equipment, cutting equipment and clicker dies. Note: Examples of components and accessories for the machines specified in 6.B.1. are moulds, mandrels, dies, fixtures and tooling for the preform pressing, curing, casting, sintering or bonding of composite structures, laminates and manufactures thereof
1B102	Metal powder “production equipment”, other than that specified in 1B002, and components as follows: N.B.: SEE ALSO 1B115.b. a. Metal powder “production equipment” usable for the “production”, in a controlled environment, of spherical, spheroidal or atomised materials specified in 1C011.a., 1C011.b., 1C111.a.1., 1C111.a.2. or in the Military Goods Controls. b. Specially designed components for “production equipment” specified in 1B002 or 1B102.a. Note: 1B102 includes: a. Plasma generators (high frequency arc-jet) usable for obtaining sputtered or spherical metallic powders with organization of the process in an argon-water environment; b. Electroburst equipment usable for obtaining sputtered or spherical metallic powders with organization of the process in an argon-water environment; c. Equipment usable for the “production” of spherical aluminium powders by powdering a melt in an inert medium (e.g. nitrogen).	M4B3d	Metal powder “production equipment” usable for the “production”, in a controlled environment, of spherical, spheroidal or atomised materials specified in 4.C.2.c., 4.C.2.d. or 4.C.2.e. Note: 4.B.3.d. includes: a. Plasma generators (high frequency arc-jet) usable for obtaining sputtered or spherical metallic powders with organization of the process in an argon-water environment; b. Electroburst equipment usable for obtaining sputtered or spherical metallic powders with organization of the process in an argon-water environment; c. Equipment usable for the “production” of spherical aluminium powders by powdering a melt in an inert medium (e.g. nitrogen). Notes: 1. The only batch mixers, continuous mixers, usable for solid propellants or propellants constituents specified in 4.C., and fluid energy mills specified in 4.B., are those specified in 4.B.3. 2. Forms of metal powder “production equipment” not specified in 4.B.3.d. are to be evaluated in accordance with 4.B.2.
1B115	Equipment, other than that specified in 1B002 or 1B102, for the production of propellant and propellant constituents, as follows, and specially designed components therefor:
1B115	a. “Production equipment” for the “production”, handling or acceptance testing of liquid propellants or propellant constituents specified in 1C011.a., 1C011.b., 1C111 or in the Military Goods Controls;	M4B1	“Production equipment”, and specially designed components therefor, for the “production”, handling or acceptance testing of liquid propellants or propellant constituents specified in 4.C.
1B115	b. “Production equipment” for the “production”, handling, mixing, curing, casting, pressing, machining, extruding or acceptance testing of solid propellants or propellant constituents specified in 1C011.a., 1C011.b., 1C111 or in the Military Goods Controls. Note: 1B115.b. does not control batch mixers, continuous mixers or fluid energy mills. For the control of batch mixers, continuous mixers and fluid energy mills see 1B117, 1B118 and 1B119. Note 1: For equipment specially designed for the production of military goods, see the Military Goods Controls. Note 2: 1B115 does not control equipment for the “production”, handling and acceptance testing of boron carbide.	M4B2	“Production equipment”, other than that described in 4.B.3., and specially designed components therefor, for the production, handling, mixing, curing, casting, pressing, machining, extruding or acceptance testing of solid propellants or propellant constituents specified in 4.C.
1B116	Specially designed nozzles for producing pyrolitically derived materials formed on a mould, mandrel or other substrate from precursor gases which decompose in the 1 573 K (1 300 °C) to 3 173 K (2 900 °C) temperature range at pressures of 130 Pa to 20 kPa.	M6B2	Nozzles specially designed for the processes referred to in 6.E.3.
1B117	Batch mixers with provision for mixing under vacuum in the range of zero to 13,326 kPa and with temperature control capability of the mixing chamber and having all of the following, and specially designed components therefor: a. A total volumetric capacity of 110 litres or more; and b. At least one ‘mixing/kneading shaft’ mounted off centre. Note: In 1B117.b. the term ‘mixing/kneading shaft’ does not refer to deagglomerators or knife-spindles.	M4B3a	Batch mixers with provision for mixing under vacuum in the range of zero to 13,326 kPa and with temperature control capability of the mixing chamber and having all of the following: 1. A total volumetric capacity of 110 litres or more; and 2. At least one ‘mixing/kneading shaft’ mounted off centre; Note: In Item 4.B.3.a.2. the term ‘mixing/kneading shaft’ does not refer to deagglomerators or knife-spindles.
1B118	Continuous mixers with provision for mixing under vacuum in the range of zero to 13,326 kPa and with a temperature control capability of the mixing chamber having any of the following, and specially designed components therefor: a. Two or more mixing/kneading shafts; or b. A single rotating shaft which oscillates and having kneading teeth/pins on the shaft as well as inside the casing of the mixing chamber.	M4B3b	Continuous mixers with provision for mixing under vacuum in the range of zero to 13,326 kPa and with a temperature control capability of the mixing chamber having any of the following: 1. Two or more mixing/kneading shafts; or 2. A single rotating shaft which oscillates and having kneading teeth/pins on the shaft as well as inside the casing of the mixing chamber;
1B119	Fluid energy mills usable for grinding or milling substances specified in 1C011.a., 1C011.b., 1C111 or in the Military Goods Controls, and specially designed components therefor.	M4B3c	Fluid energy mills usable for grinding or milling substances specified in 4.C

1C Materials

The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex
1C001	Materials specially designed for use as absorbers of electromagnetic waves, or intrinsically conductive polymers, as follows: N.B.: SEE ALSO 1C101. a. Materials for absorbing frequencies exceeding 2 × 10⁸ Hz but less than 3 × 10¹² Hz; Note 1: 1C001.a. does not control: a. Hair type absorbers, constructed of natural or synthetic fibres, with non-magnetic loading to provide absorption; b. Absorbers having no magnetic loss and whose incident surface is non-planar in shape, including pyramids, cones, wedges and convoluted surfaces; c. Planar absorbers, having all of the following: 1. Made from any of the following: a. Plastic foam materials (flexible or non-flexible) with carbon-loading, or organic materials, including binders, providing more than 5 % echo compared with metal over a bandwidth exceeding ± 15 % of the centre frequency of the incident energy, and not capable of withstanding temperatures exceeding 450 K (177 °C); or b. Ceramic materials providing more than 20 % echo compared with metal over a bandwidth exceeding ± 15 % of the centre frequency of the incident energy, and not capable of withstanding temperatures exceeding 800 K (527 °C); Technical Note: Absorption test samples for 1C001.a. Note: 1.c.1. should be a square at least 5 wavelengths of the centre frequency on a side and positioned in the far field of the radiating element. 2. Tensile strength less than 7 × 10⁶ N/m²; and 3. Compressive strength less than 14 × 10⁶ N/m²; d. Planar absorbers made of sintered ferrite, having all of the following: 1. A specific gravity exceeding 4,4; and 2. A maximum operating temperature of 548 K (275 °C). Note 2: Nothing in Note 1 to 1C001.a. releases magnetic materials to provide absorption when contained in paint. b. Materials for absorbing frequencies exceeding 1,5 × 10¹⁴ Hz but less than 3,7 × 10¹⁴ Hz and not transparent to visible light; Note: 1C001.b. does not control materials, specially designed or formulated for any of the following applications: a. Laser marking of polymers; or b. Laser welding of polymers. c. Intrinsically conductive polymeric materials with a ‘bulk electrical conductivity’ exceeding 10 000 S/m (Siemens per metre) or a ‘sheet (surface) resistivity’ of less than 100 ohms/square, based on any of the following polymers: 1. Polyaniline; 2. Polypyrrole; 3. Polythiophene; 4. Poly phenylene-vinylene; or 5. Poly thienylene-vinylene. Note: 1C001.c. does not control materials in a liquid form. Technical Note: ‘Bulk electrical conductivity’ and ‘sheet (surface) resistivity’ should be determined using ASTM D-257 or national equivalents.	M17C1	Materials for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures (i.e. stealth technology), for applications usable for the systems specified in 1.A. or 19.A. or the subsystems specified in 2.A. Notes: 1. 17.C.1. includes structural materials and coatings (including paints), specially designed for reduced or tailored reflectivity or emissivity in the microwave, infrared or ultraviolet spectra. 2. 17.C.1. does not control coatings (including paints) when specially used for thermal control of satellites.
1C007	Ceramic powders, non-“composite” ceramic materials, ceramic-“matrix”“composite” materials and precursor materials, as follows: N.B.: SEE ALSO 1C107.	M6C5	Ceramic composite materials (dielectric constant less than 6 at any frequency from 100 MHz to 100 GHz) for use in missile radomes usable in systems specified in 1.A. or 19.A.1.
1C007	a. Ceramic powders of single or complex borides of titanium, having total metallic impurities, excluding intentional additions, of less than 5 000 ppm, an average particle size equal to or less than 5 μm and no more than 10 % of the particles larger than 10 μm; b. Non-“composite” ceramic materials in crude or semi-fabricated form, composed of borides of titanium with a density of 98 % or more of the theoretical density; Note: 1C007.b. does not control abrasives. c. Ceramic-ceramic “composite” materials with a glass or oxide-“matrix” and reinforced with fibres having all of the following: 1. Made from any of the following materials: a. Si-N; b. Si-C; c. Si-Al-O-N; or d. Si-O-N; and 2. Having a “specific tensile strength” exceeding 12,7 × 10³m; d. Ceramic-ceramic “composite” materials, with or without a continuous metallic phase, incorporating particles, whiskers or fibres, where carbides or nitrides of silicon, zirconium or boron form the “matrix”; e. Precursor materials (i.e., special purpose polymeric or metallo-organic materials) for producing any phase or phases of the materials specified in 1C007.c., as follows: 1. Polydiorganosilanes (for producing silicon carbide); 2. Polysilazanes (for producing silicon nitride); 3. Polycarbosilazanes (for producing ceramics with silicon, carbon and nitrogen components); f. Ceramic-ceramic “composite” materials with an oxide or glass “matrix” reinforced with continuous fibres from any of the following systems: 1. Al2O3 (CAS 1344-28-1); or 2. Si-C-N. Note: 1C007.f. does not control “composites” containing fibres from these systems with a fibre tensile strength of less than 700 MPa at 1 273 K (1 000 °C) or fibre tensile creep resistance of more than 1 % creep strain at 100 MPa load and 1 273 K (1 000 °C) for 100 hours.	M6C6	Silicon-carbide materials as follows: a. Bulk machinable silicon-carbide reinforced unfired ceramic usable for nose tips usable in systems specified in 1.A. or 19.A.1.; Reinforced silicon-carbide ceramic composites usable for nose tips, re-entry vehicles, nozzle flaps, usable in systems specified in 1.A. or 19.A.1.
1C010	“Fibrous or filamentary materials”, as follows: N.B.: SEE ALSO 1C210 AND 9C110. a. Organic “fibrous or filamentary materials”, having all of the following: 1. “Specific modulus” exceeding 12,7 × 10⁶ m; and 2. “Specific tensile strength” exceeding 23,5 × 10⁴ m; Note: 1C010.a. does not control polyethylene. b. Carbon “fibrous or filamentary materials”, having all of the following: 1. “Specific modulus” exceeding 14,65 × 10⁶ m; and 2. “Specific tensile strength” exceeding 26,82 × 10⁴ m; Note: 1C010.b. does not control: a. “Fibrous or filamentary materials”, for the repair of “civil aircraft” structures or laminates, having all of the following: 1. An area not exceeding 1 m²; 2. A length not exceeding 2,5 m; and 3. A width exceeding 15 mm. b. Mechanically chopped, milled or cut carbon “fibrous or filamentary materials” 25,0 mm or less in length. c. Inorganic “fibrous or filamentary materials”, having all of the following: 1. “Specific modulus” exceeding 2,54 × 10⁶ m; and 2. Melting, softening, decomposition or sublimation point exceeding 1 922 K (1 649 °C) in an inert environment; Note: 1C010.c. does not control: a. Discontinuous, multiphase, polycrystalline alumina fibres in chopped fibre or random mat form, containing 3 % by weight or more silica, with a “specific modulus” of less than 10 × 10⁶ m; b. Molybdenum and molybdenum alloy fibres; c. Boron fibres; d. Discontinuous ceramic fibres with a melting, softening, decomposition or sublimation point lower than 2 043 K (1 770 °C) in an inert environment. Technical Notes: 1. For the purpose of calculating “specific tensile strength”, “specific modulus” or specific weight of “fibrous or filamentary materials” in 1C010.a., 1C010.b. or 1C010.c., the tensile strength and modulus should be determined by using Method A described in ISO 10618 (2004) or national equivalents. 2. Assessing the “specific tensile strength”, “specific modulus” or specific weight of non-unidirectional “fibrous or filamentary materials” (e.g., fabrics, random mats or braids) in 1C010. is to be based on the mechanical properties of the constituent unidirectional monofilaments (e.g., monofilaments, yarns, rovings or tows) prior to processing into the non-unidirectional “fibrous or filamentary materials”. d. “Fibrous or filamentary materials”, having any of the following: 1. Composed of any of the following: a. Polyetherimides specified in 1C008.a.; or b. Materials specified in 1C008.b. to 1C008.f.; or 2. Composed of materials specified in 1C010.d.1.a. or 1C010.d.1.b. and “commingled” with other fibres specified in 1C010.a., 1C010.b. or 1C010.c.;
1C010	e. Fully or partially resin-impregnated or pitch-impregnated “fibrous or filamentary materials” (prepregs), metal or carbon-coated “fibrous or filamentary materials” (preforms) or “carbon fibre preforms”, having all of the following: 1. Having any of the following: a. Inorganic “fibrous or filamentary materials” specified in 1C010.c.; or b. Organic or carbon “fibrous or filamentary materials”, having all of the following: 1. “Specific modulus” exceeding 10,15 × 10⁶ m; and 2. “Specific tensile strength” exceeding 17,7 × 10⁴ m; and 2. Having any of the following: a. Resin or pitch, specified in 1C008 or 1C009.b.; b. ‘Dynamic Mechanical Analysis glass transition temperature (DMA Tg)’ equal to or exceeding 453 K (180 °C) and having a phenolic resin; or c. ‘Dynamic Mechanical Analysis glass transition temperature (DMA Tg)’ equal to or exceeding 505 K (232 °C) and having a resin or pitch, not specified in 1C008 or 1C009.b., and not being a phenolic resin; Note 1: Metal or carbon-coated “fibrous or filamentary materials” (preforms) or “carbon fibre preforms”, not impregnated with resin or pitch, are specified by “fibrous or filamentary materials” in 1C010.a., 1C010.b. or 1C010.c. Note 2: 1C010.e. does not control: a. Epoxy resin “matrix” impregnated carbon “fibrous or filamentary materials” (prepregs) for the repair of “civil aircraft” structures or laminates, having all the following; 1. An area not exceeding 1 m²; 2. A length not exceeding 2,5 m; and 3. A width exceeding 15 mm. b. Fully or partially resin-impregnated or pitch-impregnated mechanically chopped, milled or cut carbon “fibrous or filamentary materials” 25,0 mm or less in length when using a resin or pitch other than those specified by 1C008 or 1C009.b. Technical Note: The ‘Dynamic Mechanical Analysis glass transition temperature (DMA Tg)’ for materials specified by 1C010.e. is determined using the method described in ASTM D 7028-07, or equivalent national standard, on a dry test specimen. In the case of thermoset materials, degree of cure of a dry test specimen shall be a minimum of 90 % as defined by ASTM E 2160-04 or equivalent national standard.	M6C1	Resin impregnated fibre prepregs and metal coated fibre preforms, for the goods specified in 6.A.1., made either with organic matrix or metal matrix utilising fibrous or filamentary reinforcements having a specific tensile strength greater than 7,62 × 104 m and a specific modulus greater than 3,18 × 106 m. Note: The only resin impregnated fibre prepregs specified in 6.C.1. are those using resins with a glass transition temperature (Tg), after cure, exceeding 145 °C as determined by ASTM D4065 or national equivalents. Technical Notes: 1. In Item 6.C.1. ‘specific tensile strength’ is the ultimate tensile strength in N/m² divided by the specific weight in N/m³, measured at a temperature of (296 ± 2)K ((23 ± 2)°C) and a relative humidity of (50 ± 5)%. 2. In Item 6.C.1. ‘specific modulus’ is the Young's modulus in N/m² divided by the specific weight in N/m³, measured at a temperature of (296 ± 2)K ((23 ± 2)°C) and a relative humidity of (50 ± 5)%.
1C011	Metals and compounds, as follows: N.B.: SEE ALSO 1C111.
1C011	a. Metals in particle sizes of less than 60 μm whether spherical, atomised, spheroidal, flaked or ground, manufactured from material consisting of 99 % or more of zirconium, magnesium and alloys thereof; Technical Note: The natural content of hafnium in the zirconium (typically 2 % to 7 %) is counted with the zirconium. Note: The metals or alloys specified in 1C011.a. are controlled whether or not the metals or alloys are encapsulated in aluminium, magnesium, zirconium or beryllium.	M4C2d	Metal powders of any of the following: zirconium (CAS 7440-67-7), beryllium (CAS 7440-41-7), magnesium (CAS 7439-95-4) or alloys of these, if at least 90 % of the total particles by particle volume or weight are made up of particles of less than 60 μm (determined by measurement techniques such as using a sieve, laser diffraction or optical scanning), whether spherical, atomised, spheroidal, flaked or ground, consisting of 97 % by weight or more of any of the above mentioned metals; Note: In a multimodal particle distribution (e.g. mixtures of different grain sizes) in which one or more modes are controlled, the entire powder mixture is controlled. Technical Note: The natural content of hafnium (CAS 7440-58-6) in the zirconium (typically 2 % to 7 %) is counted with the zirconium.
1C011	b. Boron or boron alloys, with a particle size of 60 μm or less, as follows: 1. Boron with a purity of 85 % by weight or more; 2. Boron alloys with a boron content of 85 % by weight or more; Note: The metals or alloys specified in 1C011.b. are controlled whether or not the metals or alloys are encapsulated in aluminium, magnesium, zirconium or beryllium. c. Guanidine nitrate (CAS 506-93-4); d. Nitroguanidine (NQ) (CAS 556-88-7). N.B.: See also Military Goods Controls for metal powders mixed with other substances to form a mixture formulated for military purposes.	M4C2e	Metal powders of either boron (CAS 7440-42-8) or boron alloys with a boron content of 85 % or more by weight, if at least 90 % of the total particles by particle volume or weight are made up of particles of less than 60 μm (determined by measurement techniques such as using a sieve, laser diffraction or optical scanning), whether spherical, atomised, spheroidal, flaked or ground; Note: In a multimodal particle distribution (e.g. mixtures of different grain sizes) in which one or more modes are controlled, the entire powder mixture is controlled.
1C101	Materials and devices for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures, other than those specified in 1C001, usable in ‘missiles’, “missile” subsystems or unmanned aerial vehicles specified in 9A012 or 9A112.a. Note 1: 1C101 includes: a. Structural materials and coatings specially designed for reduced radar reflectivity; b. Coatings, including paints, specially designed for reduced or tailored reflectivity or emissivity in the microwave, infrared or ultraviolet regions of the electromagnetic spectrum. Note 2: 1C101 does not include coatings when specially used for the thermal control of satellites. Technical Note: In 1C101 ‘missile’ means complete rocket systems and unmanned aerial vehicle systems capable of a range exceeding 300 km.	M17A1	Devices for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures (i.e. stealth technology), for applications usable for the systems specified in 1.A. or 19.A. or the subsystems specified in 2.A. or 20.A.
1C101	Materials and devices for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures, other than those specified in 1C001, usable in ‘missiles’, “missile” subsystems or unmanned aerial vehicles specified in 9A012 or 9A112.a. Note 1: 1C101 includes: a. Structural materials and coatings specially designed for reduced radar reflectivity; b. Coatings, including paints, specially designed for reduced or tailored reflectivity or emissivity in the microwave, infrared or ultraviolet regions of the electromagnetic spectrum. Note 2: 1C101 does not include coatings when specially used for the thermal control of satellites. Technical Note: In 1C101 ‘missile’ means complete rocket systems and unmanned aerial vehicle systems capable of a range exceeding 300 km.	M17C1	Materials for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures (i.e. stealth technology), for applications usable for the systems specified in 1.A. or 19.A. or the subsystems specified in 2.A. Notes: 1. 17.C.1. includes structural materials and coatings (including paints), specially designed for reduced or tailored reflectivity or emissivity in the microwave, infrared or ultraviolet spectra. 2. 17.C.1. does not control coatings (including paints) when specially used for thermal control of satellites.
1C102	Resaturated pyrolized carbon-carbon materials designed for space launch vehicles specified in 9A004 or sounding rockets specified in 9A104.	M6C2	Resaturated pyrolised (i.e. carbon-carbon) materials having all of the following: a. Designed for rocket systems; and b. Usable in the systems specified in 1.A. or 19.A.1.
1C107	Graphite and ceramic materials, other than those specified in 1C007, as follows:
1C107	a. Fine grain graphites with a bulk density of 1,72 g/cm³ or greater, measured at 288 K (15 °C), and having a grain size of 100 μm or less, usable for rocket nozzles and re-entry vehicle nose tips, which can be machined to any of the following products: 1. Cylinders having a diameter of 120 mm or greater and a length of 50 mm or greater; 2. Tubes having an inner diameter of 65 mm or greater and a wall thickness of 25 mm or greater and a length of 50 mm or greater; or 3. Blocks having a size of 120 mm × 120 mm × 50 mm or greater; N.B.: See also 0C004	M6C3	Fine grain graphites with a bulk density of at least 1,72 g/cc measured at 15 °C and having a grain size of 100 × 10^-6 m (100 μm) or less, usable for rocket nozzles and re-entry vehicle nose tips, which can be machined to any of the following products: a. Cylinders having a diameter of 120 mm or greater and a length of 50 mm or greater; b. Tubes having an inner diameter of 65 mm or greater and a wall thickness of 25 mm or greater and a length of 50 mm or greater; or c. Blocks having a size of 120 mm × 120 mm × 50 mm or greater
1C107	b. Pyrolytic or fibrous reinforced graphites, usable for rocket nozzles and reentry vehicle nose tips usable in “missiles”, space launch vehicles specified in 9A004 or sounding rockets specified in 9A104; N.B.: See also 0C004	M6C4	Pyrolytic or fibrous reinforced graphites usable for rocket nozzles and reentry vehicle nose tips usable in systems specified in 1.A. or 19.A.1.
1C107	c. Ceramic composite materials (dielectric constant less than 6 at any frequency from 100 MHz to 100 GHz) for use in radomes usable in “missiles”, space launch vehicles specified in 9A004 or sounding rockets specified in 9A104;	M6C5	Ceramic composite materials (dielectric constant less than 6 at any frequency from 100 MHz to 100 GHz) for use in missile radomes usable in systems specified in 1.A. or 19.A.1.
1C107	d. Bulk machinable silicon-carbide reinforced unfired ceramic, usable for nose tips usable in “missiles”, space launch vehicles specified in 9A004 or sounding rockets specified in 9A104;	M6C6a	Bulk machinable silicon-carbide reinforced unfired ceramic usable for nose tips usable in systems specified in 1.A. or 19.A.1.;
1C107	e. Reinforced silicon-carbide ceramic composites, usable for nose tips, reentry vehicles and nozzle flaps usable in “missiles”, space launch vehicles specified in 9A004 or sounding rockets specified in 9A104.	M6C6b	Reinforced silicon-carbide ceramic composites usable for nose tips, re-entry vehicles, nozzle flaps, usable in systems specified in 1.A. or 19.A.1.
1C111	Propellants and constituent chemicals for propellants, other than those specified in 1C011, as follows: a. Propulsive substances:
1C111	1. Spherical or spheroidal aluminium powder other than that specified in the Military Goods Controls, in particle size of less than 200 μm and an aluminium content of 97 % by weight or more, if at least 10 % of the total weight is made up of particles of less than 63 μm, according to ISO 2591-1:1988 or national equivalents; Technical Note: A particle size of 63 μm (ISO R-565) corresponds to 250 mesh (Tyler) or 230 mesh (ASTM standard E-11). 2. Metal powders, other than that specified in the Military Goods Controls, as follows:	M4C2c	Spherical or spheroidal aluminium powder (CAS 7429-90-5) in particle size of less than 200 × 10^-6 m (200 μm) and an aluminium content of 97 % by weight or more, if at least 10 % of the total weight is made up of particles of less than 63 μm, according to ISO 2591-1:1988 or national equivalents; Technical Note: A particle size of 63 μm (ISO R-565) corresponds to 250 mesh (Tyler) or 230 mesh (ASTM standard E-11).
1C111	a. Metal powders of zirconium, beryllium or magnesium, or alloys of these metals, if at least 90 % of the total particles by particle volume or weight are made up of particles of less than 60 μm (determined by measurement techniques such as using a sieve, laser diffraction or optical scanning), whether spherical, atomized, spheroidal, flaked or ground, consisting 97 % by weight or more of any of the following: 1. Zirconium; 2. Beryllium; or 3. Magnesium; Technical Note: The natural content of hafnium in the zirconium (typically 2 % to 7 %) is counted with the zirconium.	M4C2d	Metal powders of any of the following: zirconium (CAS 7440-67-7), beryllium (CAS 7440-41-7), magnesium (CAS 7439-95-4) or alloys of these, if at least 90 % of the total particles by particle volume or weight are made up of particles of less than 60 μm (determined by measurement techniques such as using a sieve, laser diffraction or optical scanning), whether spherical, atomised, spheroidal, flaked or ground, consisting of 97 % by weight or more of any of the above mentioned metals; Note: In a multimodal particle distribution (e.g. mixtures of different grain sizes) in which one or more modes are controlled, the entire powder mixture is controlled. Technical Note: The natural content of hafnium (CAS 7440-58-6) in the zirconium (typically 2 % to 7 %) is counted with the zirconium.
1C111	b. Metal powders of either boron or boron alloys with a boron content of 85 % or more by weight, if at least 90 % of the total particles by particle volume or weight are made up of particles of less than 60 μm (determined by measurement techniques such as using a sieve, laser diffraction or optical scanning), whether spherical, atomised, spheroidal, flaked or ground; Note: 1C111a.2.a. and 1C111a.2.b. controls powder mixtures with a multimodal particle distribution (e.g. mixtures of different grain sizes) if one or more modes are controlled.	M4C2e	Metal powders of either boron (CAS 7440-42-8) or boron alloys with a boron content of 85 % or more by weight, if at least 90 % of the total particles by particle volume or weight are made up of particles of less than 60 μm (determined by measurement techniques such as using a sieve, laser diffraction or optical scanning), whether spherical, atomised, spheroidal, flaked or ground Note: In a multimodal particle distribution (e.g. mixtures of different grain sizes) in which one or more modes are controlled, the entire powder mixture is controlled.
1C111	3. Oxidiser substances usable in liquid propellant rocket engines as follows: a. Dinitrogen trioxide (CAS 10544-73-7); b. Nitrogen dioxide (CAS 10102-44-0)/dinitrogen tetroxide (CAS 10544-72-6); c. Dinitrogen pentoxide (CAS 10102-03-1); d. Mixed Oxides of Nitrogen (MON); Technical Note: Mixed Oxides of Nitrogen (MON) are solutions of Nitric Oxide (NO) in Dinitrogen Tetroxide/Nitrogen Dioxide (N2O4/NO2 ) that can be used in missile systems. There are a range of compositions that can be denoted as MONi or MONij, where i and j are integers representing the percentage of Nitric Oxide in the mixture (e.g., MON3 contains 3 % Nitric Oxide, MON25 25 % Nitric Oxide. An upper limit is MON40, 40 % by weight). e. SEE MILITARY GOODS CONTROLS FOR Inhibited Red Fuming Nitric Acid (IRFNA); f. SEE MILITARY GOODS CONTROLS AND 1C238 FOR Compounds composed of fluorine and one or more of other halogens, oxygen or nitrogen;	M4C4a	Oxidiser substances usable in liquid propellant rocket engines as follows: 1. Dinitrogen trioxide (CAS 10544-73-7) 2. Nitrogen dioxide (CAS 10102-44-0) / dinitrogen tetroxide (CAS 10544-72-6); 3. Dinitrogen pentoxide (CAS 10102-03-1); 4. Mixed Oxides of Nitrogen (MON); Technical Note: Mixed Oxides of Nitrogen (MON) are solutions of Nitric Oxide (NO) in Dinitrogen Tetroxide/Nitrogen Dioxide (N2O4/NO2) that can be used in missile systems. There are a range of compositions that can be denoted as MONi or MONij where i and j are integers representing the percentage of Nitric Oxide in the mixture (e.g. MON3 contains 3 % Nitric Oxide, MON25 25 % Nitric Oxide. An upper limit is MON40, 40 % by weight). 5. Inhibited Red Fuming Nitric Acid (IRFNA) (CAS 8007-58-7); 6. Compounds composed of fluorine and one or more of other halogens, oxygen or nitrogen; Note: Item 4.C.4.a.6. does not control Nitrogen Trifluoride (NF3) (CAS 7783-54- 2) in a gaseous state as it is not usable for missile applications.
1C111	4. Hydrazine derivatives as follows: N.B.: SEE ALSO MILITARY GOODS CONTROLS. a. Trimethylhydrazine (CAS 1741-01-1); b. Tetramethylhydrazine (CAS 6415-12-9); c. N,N diallylhydrazine (CAS 5164-11-4); d. Allylhydrazine (CAS 7422-78-8); e. Ethylene dihydrazine; f. Monomethylhydrazine dinitrate; g. Unsymmetrical dimethylhydrazine nitrate; h. Hydrazinium azide (CAS 14546-44-2); i. Dimethylhydrazinium azide; j. Hydrazinium dinitrate (CAS 13464-98-7); k. Diimido oxalic acid dihydrazine (CAS 3457-37-2); l. 2-hydroxyethylhydrazine nitrate (HEHN); m. See Military Goods Controls for Hydrazinium perchlorate; n. Hydrazinium diperchlorate (CAS 13812-39-0); o. Methylhydrazine nitrate (MHN) (CAS 29674-96-2); p. Diethylhydrazine nitrate (DEHN); q. 3,6-dihydrazino tetrazine nitrate (1,4-dihydrazine nitrate) (DHTN);	M4C2b	Hydrazine derivatives as follows: 1. Monomethylhydrazine (MMH) (CAS 60-34-4); 2. Unsymmetrical dimethylhydrazine (UDMH) (CAS 57-14-7); 3. Hydrazine mononitrate (CAS 13464-97-6); 4. Trimethylhydrazine (CAS 1741-01-1); 5. Tetramethylhydrazine (CAS 6415-12-9); 6. N,N diallylhydrazine (CAS 5164-11-4); 7. Allylhydrazine (CAS 7422-78-8); 8. Ethylene dihydrazine (CAS 6068-98-0); 9. Monomethylhydrazine dinitrate; 10. Unsymmetrical dimethylhydrazine nitrate; 11. Hydrazinium azide (CAS 14546-44-2); 12. 1,1-Dimethylhydrazinium azide (CAS 227955-52-4) / 1,2-Dimethylhydrazinium azide (CAS 299177-50-7); 13. Hydrazinium dinitrate (CAS 13464-98-7); 14. Diimido oxalic acid dihydrazine (CAS 3457-37-2); 15. 2-hydroxyethylhydrazine nitrate (HEHN); 16. Hydrazinium perchlorate (CAS 27978-54-7); 17. Hydrazinium diperchlorate (CAS 13812-39-0); 18. Methylhydrazine nitrate (MHN) (CAS 29674-96-2); 19. 1,1-Diethylhydrazine nitrate (DEHN) / 1,2-Diethylhydrazine nitrate (DEHN) (CAS 363453-17-2); 20. 3,6-dihydrazino tetrazine nitrate (DHTN); Technical note: 3,6-dihydrazino tetrazine nitrate is also referred to as 1,4-dihydrazine nitrate.
1C111	5. High energy density materials, other than that specified in the Military Goods Controls, usable in ‘missiles’ or unmanned aerial vehicles specified in 9A012 or 9A112.a.; a. Mixed fuel that incorporate both solid and liquid fuels, such as boron slurry, having a mass-based energy density of 40 × 10⁶ J/kg or greater; b. Other high energy density fuels and fuel additives (e.g., cubane, ionic solutions, JP-10) having a volume-based energy density of 37,5 × 10⁹ J/m³ or greater, measured at 20 °C and one atmosphere (101,325 kPa) pressure; Note: 1C111.a.5.b. does not control fossil refined fuels and biofuels produced from vegetables, including fuels for engines certified for use in civil aviation, unless specially formulated for ‘missiles’ or unmanned aerial vehicles specified in 9A012 or 9A112.a.. Technical Note: In 1C111.a.5. ‘missile’ means complete rocket systems and unmanned aerial vehicle systems capable of a range exceeding 300 km.	M4C2f	High energy density materials, usable in the systems specified in 1.A. or 19.A., as follows: 1. Mixed fuels that incorporate both solid and liquid fuels, such as boron slurry, having a mass- based energy density of 40 × 10⁶ J/kg or greater; 2. Other high energy density fuels and fuel additives (e.g., cubane, ionic solutions, JP-10) having a volume-based energy density of 37,5 × 10⁹ J/m³ or greater, measured at 20 °C and one atmosphere (101,325 kPa) pressure. Note: Item 4.C.2.f.2. does not control fossil refined fuels and biofuels produced from vegetables, including fuels for engines certified for use in civil aviation, unless specifically formulated for systems specified in 1.A. or 19.A.
1C111	6. Hydrazine replacement fuels as follows: a. 2-Dimethylaminoethylazide (DMAZ) (CAS 86147-04-8);	M4C2g	Hydrazine replacement fuels as follows: 1. 2-Dimethylaminoethylazide (DMAZ) (CAS 86147-04-8).
1C111	b. Polymeric substances: 1. Carboxy-terminated polybutadiene (including carboxyl-terminated polybutadiene) (CTPB); 2. Hydroxy-terminated polybutadiene (including hydroxyl-terminated polybutadiene) (HTPB), other than that specified in the Military Goods Controls; 3. Polybutadiene-acrylic acid (PBAA); 4. Polybutadiene-acrylic acid-acrylonitrile (PBAN); 5. Polytetrahydrofuran polyethylene glycol (TPEG); Technical Note: Polytetrahydrofuran polyethylene glycol (TPEG) is a block co-polymer of poly 1,4-Butanediol (CAS 110-63-4) and polyethylene glycol (PEG) (CAS 25322-68-3). 6. Polyglycidyl nitrate (PGN or poly-GLYN) (CAS 27814-48-8).	M4C5	Polymeric substances, as follows: a. Carboxy — terminated polybutadiene (including carboxyl — terminated polybutadiene) (CTPB); b. Hydroxy — terminated polybutadiene (including hydroxyl — terminated polybutadiene) (HTPB); c. Glycidyl azide polymer (GAP); d. Polybutadiene — Acrylic Acid (PBAA); e. Polybutadiene — Acrylic Acid — Acrylonitrile (PBAN) (CAS 25265-19-4 / CAS 68891-50-9); f. Polytetrahydrofuran polyethylene glycol (TPEG). Technical Note: Polytetrahydrofuran polyethylene glycol (TPEG) is a block co-polymer of poly 1,4-Butanediol (CAS 110-63-4) and polyethylene glycol (PEG) (CAS 25322-68-3). g. Polyglycidyl nitrate (PGN or poly-GLYN) (CAS 27814-48-8)
1C111	c. Other propellant additives and agents:
1C111	1. SEE MILITARY GOODS CONTROLS FOR Carboranes, decaboranes, pentaboranes and derivatives thereof;	M4C6c1	Carboranes, decaboranes, pentaboranes and derivatives thereof
1C111	2. Triethylene glycol dinitrate (TEGDN) (CAS 111-22-8);	M4C6d1	Triethylene glycol dinitrate (TEGDN) (CAS 111-22-8);
1C111	3. 2-Nitrodiphenylamine (CAS 119-75-5);	M4C6e1	2-Nitrodiphenylamine (CAS 119-75-5);
1C111	4. Trimethylolethane trinitrate (TMETN) (CAS 3032-55-1);	M4C6d2	Trimethylolethane trinitrate (TMETN) (CAS 3032-55-1);
1C111	5. Diethylene glycol dinitrate (DEGDN) (CAS 693-21-0);	M4C6d4	Diethylene glycol dinitrate (DEGDN) (CAS 693-21-0)
1C111	6. Ferrocene derivatives as follows: a. See Military Goods Controls for catocene; b. See Military Goods Controls for Ethyl ferrocene; c. See Military Goods Controls for Propyl ferrocene; d. See Military Goods Controls for n-butyl ferrocene; e. See Military Goods Controls for Pentyl ferrocene; f. See Military Goods Controls for Dicyclopentyl ferrocene; g. See Military Goods Controls for Dicyclohexyl ferrocene; h. See Military Goods Controls for Diethyl ferrocene; i. See Military Goods Controls for Dipropyl ferrocene; j. See Military Goods Controls for Dibutyl ferrocene; k. See Military Goods Controls for Dihexyl ferrocene; l. See Military Goods Controls for Acetyl ferrocene / 1,1′-diacetyl ferrocene; m. See Military Goods Controls for ferrocene carboxylic acids; n. See Military Goods Controls for butacene; o. Other ferrocene derivatives usable as rocket propellant burning rate modifiers, other than those specified in the Military Goods Controls. Note: 1C111.c.6.o. does not control ferrocene derivatives that contain a six carbon aromatic functional group attached to the ferrocene molecule.	M4C6c2	Ferrocene derivatives, as follows: a. Catocene (CAS 37206-42-1); b. Ethyl ferrocene (CAS 1273-89-8); c. Propyl ferrocene; d. n-Butyl ferrocene (CAS 31904-29-7); e. Pentyl ferrocene (CAS 1274-00-6); f. Dicyclopentyl ferrocene (CAS 125861-17-8); g. Dicyclohexyl ferrocene; h. Diethyl ferrocene (CAS 1273-97-8); i. Dipropyl ferrocene; j. Dibutyl ferrocene (CAS 1274-08-4); k. Dihexyl ferrocene (CAS 93894-59-8); l. Acetyl ferrocene (CAS 1271-55-2) / 1,1′-diacetyl ferrocene (CAS 1273-94-5); m. Ferrocene carboxylic acid (CAS 1271-42-7) / 1,1′- Ferrocenedicarboxylic acid (CAS 1293-87-4); n. Butacene (CAS 125856-62-4); o. Other ferrocene derivatives usable as rocket propellant burning rate modifiers; Note: Item 4.C.6.c.2.o does not control ferrocene derivatives that contain a six carbon aromatic functional group attached to the ferrocene molecule.
1C111	7. 4,5 diazidomethyl-2-methyl-1,2,3-triazole (iso- DAMTR), other than that specified in the Military Goods Controls. Note: For propellants and constituent chemicals for propellants not specified in 1C111, see the Military Goods Controls.	M4C6d5	4,5 diazidomethyl-2-methyl-1,2,3-triazole (iso- DAMTR);
1C116	Maraging steels, useable in ‘missiles’, having all of the following: N.B.: SEE ALSO 1C216.	M6C8	Maraging steels, usable in the systems specified in 1.A. or 19.A.1., having all of the following: a. Having an ultimate tensile strength, measured at 20 °C, equal to or greater than: 1. 0,9 GPa in the solution annealed stage; or 2. 1,5 GPa in the precipitation hardened stage; and b. Any of the following forms: 1. Sheet, plate or tubing with a wall or plate thickness equal to or less than 5,0 mm; or 2. Tubular forms with a wall thickness equal to or less than 50 mm and having an inner diameter equal to or greater than 270 mm. Technical Note: Maraging steels are iron alloys: a. Generally characterised by high nickel, very low carbon content and use substitutional elements or precipitates to produce strengthening and agehardening of the alloy; and b. Subjected to heat treatment cycles to facilitate the martensitic transformation process (solution annealed stage) and subsequently age hardened (precipitation hardened stage).
1C117	Materials for the fabrication of ‘missiles’ components as follows: a. Tungsten and alloys in particulate form with a tungsten content of 97 % by weight or more and a particle size of 50 × 10^-6 m (50 μm) or less; b. Molybdenum and alloys in particulate form with a molybdenum content of 97 % by weight or more and a particle size of 50 × 10^-6 m (50 μm) or less; c. Tungsten materials in solid form having all of the following: 1. Any of the following material compositions: a. Tungsten and alloys containing 97 % by weight or more of tungsten; b. Copper infiltrated tungsten containing 80 % by weight or more of tungsten; or c. Silver infiltrated tungsten containing 80 % by weight ot more of tungsten; and 2. Able to be machined to any of the following products: a. Cylinders having a diameter of 120 mm or greater and a length of 50 mm or greater; b. Tubes having an inner diameter of 65 mm or greater and a wall thickness of 25 mm or greater and a length of 50 mm or greater; or c. Blocks having a size of 120 mm by 120 mm by 50 mm or greater. Technical Note: In 1C117 ‘missile’ means complete rocket systems and unmanned aerial vehicle systems capable of a range exceeding 300 km.	M6C7	Materials for the fabrication of missile components in the systems specified in 1.A., 19.A.1. or 19.A.2, as follows:. a. Tungsten and alloys in particulate form with a tungsten content of 97 % by weight or more and a particle size of 50 × 10^-6 m (50 μm) or less; b. Molybdenum and alloys in particulate form with a molybdenum content of 97 % by weight or more and a particle size of 50 × 10^-6 m (50 μm) or less; c. Tungsten materials in the solid form having all of the following: 1. Any of the following material compositions: i. Tungsten and alloys containing 97 % by weight or more of tungsten; ii. Copper infiltrated tungsten containing 80 % by weight or more of tungsten; or iii. Silver infiltrated tungsten containing 80 % by weight or more of tungsten; and 2. Able to be machined to any of the following products: i. Cylinders having a diameter of 120 mm or greater and a length of 50 mm or greater; ii. Tubes having an inner diameter of 65 mm or greater and a wall thickness of 25 mm or greater and a length of 50 mm or greater; or iii. Blocks having a size of 120 mm × 120 mm × 50 mm or greater
1C118	Titanium-stabilised duplex stainless steel (Ti-DSS) having all of the following: a. Having all of the following characteristics: 1. Containing 17,0 – 23,0 weight percent chromium and 4,5 – 7,0 weight percent nickel; 2. Having a titanium content of greater than 0,10 weight percent; and 3. A ferritic-austenitic microstructure (also referred to as a two-phase microstructure) of which at least 10 percent is austenite by volume (according to ASTM E-1181-87 or national equivalents); and b. Having any of the following forms: 1. Ingots or bars having a size of 100 mm or more in each dimension; 2. Sheets having a width of 600 mm or more and a thickness of 3 mm or less; or 3. Tubes having an outer diameter of 600 mm or more and a wall thickness of 3 mm or less.	M6C9	Titanium-stabilized duplex stainless steel (Ti-DSS) usable in the systems specified in 1.A. or 19.A.1. and having all of the following: a. Having all of the following characteristics: 1. Containing 17,0 – 23,0 weight percent chromium and 4,5 – 7,0 weight percent nickel; 2. Having a titanium content of greater than 0,10 weight percent; and 3. A ferritic-austenitic microstructure (also referred to as a two-phase microstructure ) of which at least 10 % is austenite by volume (according to ASTM E-1181-87 or national equivalents); and b. Any of the following forms: 1. Ingots or bars having a size of 100 mm or more in each dimension; 2. Sheets having a width of 600 mm or more and a thickness of 3 mm or less; or 3. Tubes having an outer diameter of 600 mm or more and a wall thickness of 3 mm or less.
1C238	Chlorine trifluoride (ClF3).	M4C4a6	Compounds composed of fluorine and one or more of other halogens, oxygen or nitrogen; Note: Item 4.C.4.a.6. does not control Nitrogen Trifluoride (NF3) (CAS 7783-54- 2) in a gaseous state as it is not usable for missile applications.

1D Software

The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex
1D001	“Software” specially designed or modified for the “development”, “production” or “use” of equipment specified in 1B001 to 1B003.	M6D1	“Software” specially designed or modified for the operation or maintenance of equipment specified in 6.B.1.
1D101	“Software” specially designed or modified for the operation or maintenance of goods specified in1B101, 1B102, 1B115, 1B117, 1B118 or 1B119.	M4D1	“Software” specially designed or modified for the operation or maintenance of equipment specified in 4.B. for the “production” and handling of materials specified in 4.C.
1D101	“Software” specially designed or modified for the operation or maintenance of goods specified in1B101, 1B102, 1B115, 1B117, 1B118 or 1B119.	M6D1	“Software” specially designed or modified for the operation or maintenance of equipment specified in 6.B.1.
1D103	“Software” specially designed for analysis of reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures.	M17D1	“Software” specially designed for reduced observables such as radar reflectivity, ultraviolet/infrared signatures and acoustic signatures (i.e. stealth technology), for applications usable for the systems specified in 1.A. or 19.A. or the subsystems specified in 2.A. Note: 17.D.1. includes “software” specially designed for analysis of signature reduction.

1E Technology

The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	The corresponding systems, equipment and components as identified in Council Regulation (EC) No 428/2009 of 5 May 2009 setting up a Community regime for the control of exports, transfer, brokering and transit of dual-use items	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex	Missile Technology Control Regime (M.TCR): Equipment, software and technology annex
1E001	“Technology” according to the General Technology Note for the “development” or “production” of equipment or materials specified in 1A001.b., 1A001.c., 1A002 to 1A005, 1A006.b., 1A007, 1B or 1C.	M	“Technology”, in accordance with the General Technology Note, for the “development”, “production” or “use” of equipment or “software” specified in 1.A., 1.B., or 1.D.
1E101	“Technology” according to the General Technology Note for the “use” of goods specified in 1A102, 1B001, 1B101, 1B102, 1B115 to 1B119, 1C001, 1C101, 1C107, 1C111 to 1C118, 1D101 or 1D103.	M	“Technology”, in accordance with the General Technology Note, for the “development”, “production” or “use” of equipment or “software” specified in 1.A., 1.B., or 1.D.
1E102	“Technology” according to the General Technology Note for the “development” of “software” specified in 1D001, 1D101 or 1D103.	M6E1	“Technology”, in accordance with the General Technology Note, for the “development”, “production” or “use” of equipment, materials or “software” specified in 6.A., 6.B., 6.C. or 6.D.
1E102	“Technology” according to the General Technology Note for the “development” of “software” specified in 1D001, 1D101 or 1D103.	M17E1	“Technology”, in accordance with the General Technology Note, for the “development”, “production” or “use” of equipment, materials or “software” specified in 17.A., 17.B., 17.C. or 17.D. Note: 17.E.1. includes databases specially designed for analysis of signature reduction
1E103	[M6E2]“Technology” for the regulation of temperature, pressure or atmosphere in autoclaves or hydroclaves, when used for the “production” of “composites” or partially processed “composites”.	M6E2	“Technical data” (including processing conditions) and procedures for the regulation of temperature, pressures or atmosphere in autoclaves or hydroclaves when used for the production of composites or partially processed composites, usable for equipment or materials specified in 6.A. or 6.C
1E104	“Technology” relating to the “production” of pyrolytically derived materials formed on a mould, mandrel or other substrate from precursor gases which decompose in the 1 573 K (1 300 °C) to 3 173 K (2 900 °C) temperature range at pressures of 130 Pa to 20 kPa. Note: 1E104 includes “technology” for the composition of precursor gases, flow-rates and process control schedules and parameters.	M6E1

CATEGORY 2 — MATERRIALS PROCESSING

Reading this document does not replace reading the official text published in the Official Journal of the European Union. We assume no responsibility for any inaccuracies arising from the conversion of the original to this format.

This text is published under EUR-Lex's own terms of reuse, not a Legalize or public-domain licence. EUR-Lex
Creative Commons Attribution 4.0 International (CC BY 4.0)
© European Union, https://eur-lex.europa.eu — Source: EUR-Lex (Publications Office of the European Union). Reused under the Creative Commons Attribution 4.0 International (CC BY 4.0) licence. Only EU legislation published in the printed Official Journal of the European Union is deemed authentic; consolidated texts are reproduced here for documentation purposes and have been reformatted to Markdown.